1. To satisfy design limitations it is necessary to determine the effect of the 4.5 kN tension in the cable on the truss. For this purpose replace this force by its equivalent of two forces at A, F: parallel and Ea perpendicular to the truss. Determine F; and Fn.

1. To satisfy design limitations it is necessary to determine the effect of the 4.5 kN tension in the cable on the truss. For this purpose replace this force by its equivalent of two forces at A, F: parallel and Ea perpendicular to the truss. Determine F; and Fn.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: One end of a timber roof truss is supported on a brick wall but not securely fastened. The reaction…

A: Consider the diagram shown below for the given forces,

Q: 1: Determine the forces and state if its tension or compression in members AB, AH, BH, BG, BC and…

Q: If roller at B can sustain a maximum load of 3kN,determine the largest magnitude of each of the…

A: The free-body diagram of the truss is as follows.

Q: 1) Neglecting friction and the radius of the pulley, determine (a) the tension in cable ADB, (b) the…

A: According to the details provided in the question, we need to calculate 1. tension in the cable 2.…

Q: Q4 Determine the resultaut of the forces shown, and locate it with respect to point (A)

A: Force and momentum balance based question. The entire amount of force exerted on the object or body,…

Q: For the frame and loading shown, draw the free-body diagram(s) needed to determine the components of…

A: The free body diagram of the frame is given below,

Q: If the roller at B can sustain a maximum load of 3kN, determine the largest magnitude of each of the…

A: Given: Maximum load at B is 3 KN. Drawing the dree body diagram

Q: A. Determine the equivalent resultant force that could replace the concentrated forces. B.…

A: According to the condition of equilibrium, The net force and moment at any point about any axis on…

Q: Consider the frame as shown. Determine: a) The forces acting on member AB at A and B. b) The forces…

A: According to the details provided in the question, we need to calculate forces at points A , B and…

Q: Problem 2 A transmission tower is held by three guy wires anchored by bolts a с, and D. If the…

Q: A 10-H boom is acted upon by the 50 - lb force shown. Determine the tension in each cable.

A: Write the position vector of point B and C, Write the unit vector from B to D.

Q: 2/88 If the resultant of the forces shown passes through point A, determine the magnitude of the…

Q: 3. A 1600-lb crate is supported by three cables as shown. Determine the tension in each cal B 36 in.…

A: Hello dear, According to our guidelines I can solve only first question, kindly repost your second…

Q: For the boom and loading of Prob. 2.97, determine the magnitude of the load P.(Reference to Problem…

A: Given Tension at load at AB = 183 lb To find Tension in cable AC The load P respect to TAC

Q: 3. A house with 932 kN weight is built on a steep slope defined by points A, B, and C. To help…

A: Dear student, According to the expert guidelines I am allowed to answer only…

Q: 5. In order to raise the lamp post from the position shown, a force F = 200 lb. is applied on the…

Q: B. Six steel cables are supporting a circular heavy molding of diameter 2.5 m from overhead point.…

A: Given data: d = 2.5 m W=3 kN/m Need to determine the tension in the steel cable.

Q: The tongs shown are used to apply a total upward force of 45 kN on a pipe cap. Determine the forces…

A: From the symmetry FA =FB=22.5 Thus, Draw the F.B.D of the member ADF of the machine frame.

Q: For the frame and loading shown, determine the components of all forces acting on member ABE.

A: Free body diagram of member BC: Moment about the point C: ∑MC=0 (↻+) (2400×1.2)-(By×2.4)=0By=1200N…

Q: 2. Two cables support a 400- Ib weight as shown. Determine the tension in each cable. 400 - Ib

Q: Determine the components of all the forces on member ABC of the frame shown. F = l00 N %3D 240 mm…

Q: A piece of plywood in which several holes are being drilled successively has been secured to a…

A: Given Data: The applied couple is M = 12 N·m. Dimensions in the figure. Part (a) The expression of…

Q: ie is being used to cut threads on a rod. If 18-Ib forces are applied as shown, determine the…

A: Given:P=18 lbr=7.5 inx=0.5 in

Q: Determine the magnitude of the gripping forces produced when two 300-N forces are applied as shown.

A: Free body diagram of the problem is shown in the figure. Member AC is connected to both members AB…

Q: Determine the tension developed in cables AB, AC, and AD

Q: Determine the forces in members: d) BF, e) BC

Q: Determine the tension in each segment of the cable shown

A: Given: To determine: Tension in all cables

Q: Determine the magnitude of the force supported by the pin at C of the loaded frame.

Q: Two cables tied together as shown in figure 1. Knowing that Q = 60 lbs and that the system is in…

A: Consider the free body diagram of the point C as shown below.

Q: A 5-m long simply supported timber beam carries two concentrated loads as shown. If L = 16 KN and M…

Q: For the post loaded as shown, determine (a) the required tension in rope AC if the resultant of the…

A: Given, Force acting at point C, P1=500 N Force acting at point C, P2=200 N

Q: If the resultant of the forces shown passes through point A, determine the magnitude of the unknown…

A: Draw the free body diagram and transfer the tension, T2, 650N forces to force and moment as shown…

Q: Determine the magnitudes of the forces C and T, which, along with the other three forces shown, act…

Q: Q1: Determine the magnitudes of the forces C and T, which, along with the other three 4 kN forces…

A: As per given Question We have to find the magnitude of force T And C

Q: . The 3200-lb weight is supported by two cables. Knowing that the resultant of the cable tensions T1…

A: By sine law T1sinθ1=T2sinθ2=Wsinθ3

Q: PROBLEM 2.89 A rectangular plate is supported by three cables as shown. Knowing that the tension in…

Q: A machine component is subjected to the forces and couples shown. The component is to be held in…

A: Given System under loading To find Location of rivet

Q: 4. Find the forces at points A and B of the landing gear shown. トーがート

Q: 4. Determine the tension in each of the three supporting cables AB, BC, and CD, and the angle 0…

Q: 1. Determine the vertical and horizontal components of the reactions at pin A and the tension…

A: Solution:

Q: 3/2 A carpenter holds a 12-lb 2-in. by 4-in. board as shown. If he exerts vertical forces on the…

Q: The uniform 18kg Bar OA is held in the position shown by a smooth pin at 0, and the cable AB which…

Q: Determine the magnitude of the reactions at A and C (resultant). 2m 1.8m 3m 12KN/m

A: The equivalent force due to uniformly varying load can be determined as the area of a triangle…

Q: The force-couple system shown acts on a trapezoidal plate. a. Determine the value of M1 if the…

Q: 1. The cable supports a girder which weighs 750 lb/ft. Determine the tension in the cable at points…

Q: 1. The pulley arrangement shown supports a concrete block that weighs 13.5 kN Determine the tension…

Q: Member BC exerts on member AC a force P directed along line BC. Knowing that P must have a 325-N…

Question

1. To satisfy design limitations it is necessary to determine the effect of the 4.5 kN tension in
the cable on the truss. For this purpose replace this force by its equivalent of two forces at A,
F: parallel and Ea perpendicular to the truss. Determine F; and Fn.
A
1250
4.5 kN
30°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Drawing FBD

VIEW

Calculating forces

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The uniform 10 kg rod AB is supported by a ball and socket joint at A and by the cord CG that is attached to the midpoint G of the rod. Knowing that the rod leans against a frictionless vertical wall at B and that the tension in the cord CG, TCG=52.1 N, determine the following a.) Which of the following best shows the equivalent force-couple set at point A of the tension at cord CG, TCG? Choices: a F= -36.8 N i + 24.5 N j - 27.6 N k M = -7.36 Nm i - 11.03 Nm j b F= -36.8 N i + 24.5 N j - 27.6 N k M = -7.36 Nm i - 29.4 Nm k c F= 36.8 N i - 24.5 N j + 27.6 N k M = 7.36 Nm i + 11.03 Nm j d F= 36.8 N i - 24.5 N j + 27.6 N k M = 7.36 Nm i + 29.4 Nm k b.) Which of the following moments is equal to zero? Choices: The moment of the tension in cord CG, TCG about point OThe moment of the tension in cord CG, TCG about point AThe moment of the tension in cord CG, TCG about point BThe moment of the tension in cord CG, TCG about axis AB
Three wires are connected at point D, which is located 18 in. below the T-shaped pipe support ABC. Determine the tension in each wire when a 180-lb cylinder is suspended from point D as shown.
The pipe ACDE is supported by ball-and-socket joints at A and E and by the wire DF . Determine the tension in the wire when a 640-N load is applied at B as shown.
Three wires are connected at point D, which is located 18 in. below the T-shaped pipe support ABC. Determine the tension in wire AD when a 150 lb cylinder is suspended from point D as shown.
Determine the forces in each member of the right half of the truss using the method of joints. Given: F1=5 kN F2=12 kN F3=4 kN F4= 11 kN L=8 m
Rod AD is acted upon by a vertical force P at end and by two equal and opposite horizontal forces of magnitude Q at points B and C . Neglecting the weight of the rod, express the angle 0 corresponding to the equilibrium position in terms of P and Q.
The rigid L-shaped member ABC is supported by a ball-and-socket joint at A and by three cables. If a 1.8-kN load is applied at F , determine the tension in each cable.
Solve Prob. 4.140, subject to the restriction that H must lie on the y axis.(Reference to Problem 4.140):Two 2 × 4-ft plywood panels, each with a weight of 12 lb, are nailed together as shown. The panels are supported by ball-and-socket joints at A and F and by the wire BH . Determine (a) the location of H in the xy plane if the tension in the wire is to be minimum, (b) the corresponding minimum tension.
Solve Prob. 2.125 assuming that y = 275 mm.(Reference to Problem 2.125):Collars A and B are connected by a 525-mm-long wire and can slide freely on frictionless rods. If a force P = (341 N) j is applied to collar A , determine (a) the tension in the wire when y = 155 mm, (b) the magnitude of the force Q required to maintain the equilibrium of the system.
A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B, C and D . If the tension in wire AB is 840 lb, determine the vertical force P exerted by the tower on the pin at A.
2)All external force of 140N is applied to the truss at joint B. Draw the Free BodyDiagram of the truss.
A sign that weighs 15.0 N hangs from the end of a beam of length 4 meters and weight 10 Newtons. Beam is hinged at the wall and supported by a cable attached to the beam 3.00 meters from the wall as shown. Determine the tension in the cable. Determine the x- and y-components of the reaction force at the hinge. (3 total answers)