Q2) The slotted arm pivots about O and maintains the relation between the motions of sliders A and B and their control rods. Each small pivoted block is pinned to its respective slider and is constrained to slide in its rotating slot. Show that the displacement x is proportional to the reciprocal of y. Then estab- lish the relation between the velocities va and vg- Also, if vA is constant for a short interval of motion, determine the acceleration of B. e 2:28

Q2) The slotted arm pivots about O and maintains the relation between the motions of sliders A and B and their control rods. Each small pivoted block is pinned to its respective slider and is constrained to slide in its rotating slot. Show that the displacement x is proportional to the reciprocal of y. Then estab- lish the relation between the velocities va and vg- Also, if vA is constant for a short interval of motion, determine the acceleration of B. e 2:28

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the slope and deflection at point B of the steel beamshown in the figure. The reactions are already given. Let E = 29(10^3) ksi and I = 800in^4
If point B settles by 2mm, determine the reaction of the beam shown. Assume EI is constant withE=200GPa and I =400x106mm4. (Use either Three Moment Equation or Slope Deflection Method)
Use area moment method in this problem and find the vertical reaction at C and A in kN and moment reaction at A in kN-m. Also the deflection at point B in mm. a=4m b=12kN/m c=40kN
Analyze the propped beam loaded as shown below: use either double integration or area moment method. Determine the reaction at the roller support. Ans.: RA = Blank 1 kN Determine the deflection at midspan of the beam. Determine the slope at 2m from the roller support.
Circular beam with modulus of elasticity E=70 GPaA distributed load of 35 kN/m and a bending moment of k⨯2.3 kNm are applied. Using the analytical (integral) method;a) Determine the support reactions and the moment of inertia of the section.b) Moment function and 2nd order differential equation c) Boundary conditions, slope and deflection equationsd) the angle of inclination at point B (2),e) Determine the deflection (3) at point C.K=1.85 D (mm) L (m) k⨯87 k⨯1.5
Solve Problems by the moment-areamethod. EI is constant unless otherwise noted. Compute the horizontal deflection at D and verti- cal deflection at B in Figure P7.21. The elastomeric pad at C acts as a roller.
Use Slope-Deflectian Method or Moment Distribution Method to solve for the unknows on the 120mm x 200 mm beam shown in the figure. E = 80 GPa. a. Fixed-end moment (FEM) at joint A on member AB. Indicate negative if counter-clackwise. b. Moment at A c. Moment at C
A solid circular bar ABCD with fixed sup-ports is acted upon by torques T0 and 2T0 at the loca-tions shown in the figure. (a) Obtain a formula for the maximum angle oftwist fmax of the bar.(b) What is fmax if the applied torque T0 at B isreversed in direction?
Calculate the value of the moment reaction at A of the beam shown below. If the direction is counterclockwise, affix negative sign betore the numerical value. Answer to the nearest whole number, units in kN-m. Use Moment Distribution Method.
SOLVE FOR THE REACTIONS AND DRAW THE SHEAR AND MOMENT DIAGRAMS OF THE FOLLOWING BEAMS USE BOTH 1.THREE-MOMENT EQUATION 2.SLOPE-DEFLECTION METHOD FOR ALL THE BEAMS: ASSUME w = 13 P = 28 EI = constant
Determine the value of the maximum deflection and rotation at bothsupport for the beam loading shown if the uniformly distributed load ωis 58 N/m. Assume EI to be constant all throughout thespan.
Given a cantilever beam of length L=3.7meters. The left support “A” is fixed while the right end “B” is free. With constant EI=20000 KN-m2. A downward uniform load of 85KN/m is applied all throughout its span. Using Area Moment Method (AMM), calculate the deviation of B when a tangent line is drawn at A, i.e. tB/A? Express your answer in "millimeters" in 2 decimal places. Hint: tB/A = deflection at free end. Include negative (-) sign if tB/A is negative.