Answered: 50 kN 20 kN/m 3m 2m 4m 2m 5m, 2EI 6m,…

Engineering

Civil Engineering

50 kN 20 kN/m 3m 2m 4m 2m 5m, 2EI 6m, 3EI

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the reactions in pin A, B, C and D. 0.5 m 1.5 m 0.75 m 2.25 m 1.5 m 3 m 0.5m 0.75 m 500 N

Q: Determine the forces FE, FB & AB of the truss using method of sections. 3m -2m 2m- 5 kN 55 kN 5kN

Q: For the timber beam shown, draw the shear and moment diagrams and determine the maximum bending stre...

Q: A square footing has dimensions 2 m x 2 m and founded at a depth of 2 m. Consider the following stat...

Q: For this Problem, kindly refer to our Textbook, Structural Analysis Fourth Edition By Aslam Kassimal...

A: Given;

Q: Using slope deflection method. Determine fix-end moment at member AB, BC and moment at C.

Q: A truck with axle loads shown rolls across a 10-m span. What is the maximum bending moment and maxim...

A: For the given rolling loads across a 10m span, the maximum shear and bending moment have to be compu...

Q: Find the slope of the finished roadway.

Q: A rectangul3 the water. The gate is 4 feet in length and 5 feet wide. Answer the following questions...

A: Given data - To find-

Q: Are the following A36 steel elements slender or non-slender? • The flanges of W8X67 • The web of W1...

A: The value of fy for A36 steel is 36 ksi or 250 MPa. The modulus of elasticity (E) is 29000 ksi. The ...

Q: maximum shearing stress on the beam

A: To determine: The maximum shear stress of the beam.

Q: Question 1. Determine the support reactions and draw the shear force and bending moment diagrams for...

A: Given : Different beams with different loading conditions Draw SFD and BMD and find the support reac...

Q: Lake Taal has a volume of 458 cubic km, and its rate of inflow and outflow are both 175 cubic km/yea...

A: Given, V=458 km3q=175 km3/yeart=0 Pollutant concentration p =0.06% Pollutant concentration in the in...

Q: A rectangular flume of most economical secțion has a base width of 3 m and carries water at 2.70 m°/...

A: Given dara, Base width = 3 m Discharge (Q) = 2.7 m³/s To find out the water carrying capacity incre...

Q: Problem 3: Determine the ratio of . F,and F, are internal forces in member of 1 and 2 F, respectivel...

A: Given data -

Q: Jsing SDM for the frame shown below, determine the following structural parameters, FEM and support ...

A: Fix end moment at C for member CB MFBC = -( 9wl2/192) - PL/8 = -(5×24×62/192) - 20×6/8 ...

Q: 1. Compute the volume of cur material to be removed to reach sub-grade between stations 4+50 and 5+0...

A: Given Data -

Q: If the given beam has constant EI, determine the maximum positive and negative moment

Q: Is it easier to solve for the head loss when it's a laminar flow than turbulent flow? Discuss all po...

A: Laminar flow - it is type of flow inwhich the fluid moves in a smooth way without mixing or only lit...

Q: A Doubly Reinforced concrete beam has an effective depth of 600mm and a width of 325mm. It is reinfo...

A: Note- Ultimate moment capacity value written is a wrong value. After calculation its exact value is ...

Q: Using MDM for the continuous beam below, determine the following structural parameters and support m...

Q: In a rectangular channel 3.5 m wide laid at a slope of 0.0036, uniform flow occurs at a depth of 2 m...

Q: For a roof truss system of an industrial building, following data is given Span of truss = 6.0 m Spa...

Q: the following travel times were observed for four vehicles traversing a one km segment of highway. O...

Q: The common tangent BC of a reversed curve with a common radius is 280.5 and has azimuth of 312deg 29...

Q: (Irregular Sections) The areas in cut of two irregular sections 35 m apart are 34 m? and 56 m? respe...

A: Determining the quantity of earthwork required on a project is an essential part of route planning. ...

Q: 20 kN 24 kN/m 16 kN/m 5 m 31 A 3.0 m - 3.0 m

Q: The magnetic bearing of a line AB was found 268°. If the local attraction at this station was 3° Eas...

A: Given data, Magnetic bearing of line AB = 268° Declination= 12°west Local attraction= 3° True bearin...

Q: A compound curve is composed of 3 and 5 degree curves with I1 = 22 degree and I2=30 degree, respecti...

Q: Situation. The one way slab has a thickness of 200 mm. It is reinforced with 25 mm o bars with 150 m...

A: A one-way slab is one in which the larger span to the shorter span ratio is more than two. In other ...

Q: Problem 2: In the following structure determine the internal force in spring. Assume K EA %3D 4L E E...

Q: 3. The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failu...

Q: Hagen-Poiseuille equation; (2) Darcy-Weisbach equation;

Q: For the timber beam shown, draw the shear and moment diagrams and determine the maximum bending stre...

Q: Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attachin...

Q: Determine all reactions in the given beam. Draw the shear & moment diagram for the beam. USING MOMEN...

Q: f’c = 28 fy = 415 Mpa ex= 320mm a. Calculate depth of neutral axis b. Calculate the stress in extrem...

A: The neutral axis is an axis in the cross-section of a beam (a member resisting bending) or shaft alo...

Q: Slope Deflection Method nstructions: Solve the following problems completely using Slope Deflection ...

Q: 18m A 9m C 7.50m VP V166N Compute for P If CABLE BC is Horizon tal w9 B

Q: 2: Determine the area required for a new landfill site with a projected life of 20 years for a popul...

Q: 225 P= 8 P- 10 9- 18 1(m) 나 1.50 (m) 2 (m) 4.50 (m)

Q: Determine the nature and magnitude of the forces in members BC, CH,GH, DE and EF

Q: Problem 4: External force Pis applied at point O. Determine the angle a such that Fos (internal forc...

Q: Using SDM for the frame shown below, determine the following structural parameters. FEM and support ...

Q: a) Compute the depth of compression block and b) the ultimate moment capacity of the beam shown in...

A: Answer We are given f'c = 28 Mpa fy = 414 Mpa d = 600 mm As = 5-32 mm As = 5*π4*322 As = 4021.24 ...

Q: Determine the reaction at point A and the tension in cord AB. (Partial ans. TAB = 7000 lb) 30° B 800...

A: The system is in equilibrium, so net moment about support must be zero, Since C is pin joint, theref...

Q: (a) Draw three co entire beam, a section cut (2)

Q: 20 kN 24 kN/m 16 kN/m 5 m A 3.0 m - - 3.0 m 31

A: An indeterminate frame structure is given and it has been asked to determine moment in member AB. Pl...

Q: Determine the force in members KJ, JN,ND and C D.

A: Given data-

Q: A soil sample has bulk unit weight of 19 kN/m³ and a water content of 7%. Determine the amount of wa...

Question

Calculate the value of the moment reaction at A of the beam shown below. If the direction is counterclockwise, affix negative sign betore the numerical value. Answer to the nearest whole number, units in kN-m. Use Moment Distribution Method.

50 kN
20 kN/m
3m
2m
4m
2m
5m, 2EI
6m, 3EI
150mm
E = 180 GPa
| =
200mm
75mm diameter hole at the center

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

24.5m is the right ans.
a = 3.7 m b = 31 kN-m c = 35 kN
q = 4.6 kN/m
Q. 79
q=3.15 kn/m , a=3.15m
8.TAPE MEASUREMENTSa. A line was recorded as 1650.00 meters long. It is measured with a 0.65 kg standard tape30.00m long at 20°C under a 50N pull supported at both ends. During the measurementthe temperature was 5°C and the tape was suspended under a 75N pull. The line wasinclined on a 3% grade. What is the true inclined distance? E = 200GPa, A = 3.0 mm² andthe coefficient of linear expansion is 0.0000116 m/°C.b. A line was recorded as 2000.00 meters long. It is measured with a 0.65 kg standard tape30.00m long at 20°C under a 50N pull supported at both ends. During the measurementthe temperature was 5°C and the tape was suspended under a 75N pull. The line wasinclined on a 3% grade. What is the true inclined distance? E = 200GPa, A = 3.0 mm² andthe coefficient of linear expansion is 0.0000116 m/°C.
Three independent lines oflevels are run from BM1 to BM2. Route A is 6km long, route B is 4 km long and route C is 8km long. By route A, BM2 is 82.27 m aboveBM1, by route B, BM2 is 82.40 m above BM1and by route C, BM2 is 82.10 m above BM1.1. Compute the probable elevation of BM2if the elevation of BM1 is 30.5 m. a. 113.13 m c. 113.45 m b. 112.79 m d. 113.06 m
Help ASAP! w: 2.8 kN/m , a: 3.4 m, b: 3.5 m, theta: 30 degrees
HELP ASAP!!! P1: 280 N, P2: 590 N, x: 1.11 m, theta: 38 degrees
pls help me solve this. 1) from point A in bet. B and C, the angles of elevation of B and C are 18deg30' and 8deg15' respectively. (' - this is mins.) Point C is 2000m from A, and B is 1200m from A. Elev. of A is 219.42m above sea level. DETERMINE: a) Compute the diff. in elev. Bet. B and C, considering the effect of earths curvature and refraction. b) compute the diff. in elev. bet. A and C c) compute the elevation of B. *answer in 4 dec places *with diagram pls thank you. I'll give your answer a LIKE for helping me.
An engineer's level with stadia constant of 0.30 m was set up on the line between A and B, the following crosshair readings were observed. If the stadia interval factor of the levels is 100, determine the length of line AB. Show all your complete solution and illustration (if applicable)
Answer problem D and E only.a = 41.60 kNb = 35.50 kN/mc = 19.00 kN/m