Q2: Water is flowing through an inclined pipe and two sections (section 1 and section 2 ) of the pipe are considered. The diameter of the pipe at section 1 is (200 + 33 ) mm and (120 + 33 ) mm at section 2. The elevations of the sections 1 and 2 above datum are (800 + 33) cm and (400 + 33 ) cm respectively. If the pressure at section 1 is 40x104 N/m? and the discharge through the pipe is 60 litres per second, calculate the intensity of pressure at section 2. /

Q2: Water is flowing through an inclined pipe and two sections (section 1 and section 2 ) of the pipe are considered. The diameter of the pipe at section 1 is (200 + 33 ) mm and (120 + 33 ) mm at section 2. The elevations of the sections 1 and 2 above datum are (800 + 33) cm and (400 + 33 ) cm respectively. If the pressure at section 1 is 40x104 N/m? and the discharge through the pipe is 60 litres per second, calculate the intensity of pressure at section 2. /

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water is flowing at the rate of 4.7 cu.m./min. through a 150mm-dia. pipe which slopes downwardsuch that a 75mm-dia. exit orifice is 0.60m lower than the upper end. Assume no friction loss. The sharp edged orificehas a coefficient of contraction of 0.65. What is the pressure at the point A in KPa?
Describe some Conditions for passive pressure case.
The rectangular bin with an inclined gate AB is filled with water to the depth shown. Determine the location in meters along with the inclination of the center of pressure from the water surface when the total pressure is acting on gate AB x=0.82 a=2.02 m b=30 degrees asap 15 mins
Gate B below is 30 cm high, 60 cm wide into the paper, and hinged at the top. If the water depth is h = 75 cm, what pressure is required in the adjacent air compartment for the gate to remain closed as shown? Take the specific weight of the water as γwater = 9810 N/m^3
Water flows from A to E through the pipe system shown. It is known that the flow in pipe BFGC IS 30 LITERS /SEC. and that the pressure head at A is 60 m. Assuming that f =0.022 and that all the pipes are level, determine the total flow from A to E and the pressure heads at B, C, D and E.
A 12” pipe contains a short section in which the diameter is gradually reduced to 6” and then enlarged again to 12”. The 6” section is 2 ft below Section A in the 12” where the pressure is 75 psi. If a differential gage containing mercury is attached to the 12” and 6” sections, what is the deflection of the gage when the flow of water is 4.25 cfs downward? Draw the figure
Water flows from a large reservoir at the rate of 0.0137 m3/s through the system shown in the Fig. below. Calculate the pressure at B. NB: Use f = 0.017 (friction factor) and fT = 0.010 in zone of complete turbulence. Hint: Include minor losses, assume K = 1.0 for the inlet or entrance and use the applicable appendix at the back of the textbook to obtain the pipe parameters.
Water flows upwards through a venturi section. The venturi section varies indiameter from 15cm at the top and bottom to 5cm at the narrowest point. A differential pressuretransducer measured a pressure difference of 43kPa. Assuming steady flow, determine the velocity ofthe flow through the narrowest region and the discharge through the meter. Assume that water has adensity of 1g/cm 3 .c) Is the fluid pressure at the bottom of the venturi section greater than, less than, or equal to the fluidpressure at the narrowest region?
Points A and B are 4.8km apart along a 60cm new cast iron pipe carrying water. A is 10cm higher than B. If the pressure at A is 140kPa higher than B How much will the flow be? use C = 110
Water flows upwards through a venturi section. The venturi section varies indiameter from 15cm at the top and bottom to 5cm at the narrowest point. A differential pressuretransducer measured a pressure difference of 43kPa. Assuming steady flow, determine the velocity ofthe flow through the narrowest region and the discharge through the meter. Assume that water has adensity of 1g/cm 3 .b) The discharge through the venturi section
A vertical triangular gate having a height “h” and a base “b” issubmerged in water. Identify the following: 1. Depth of center of pressure with its vertex at the liquid surface.2. If the vertex is 1 meter below the surface, determine the locationof center of pressure from the surface if b = 4 m and d = 3 m,and3. determine its hydrostatic pressure on one side of the gate.
If F=80 N, determine the magnitude and coordinate diretion angles of the couple moment. The pipe assembly lies in the x-y plane.