4m long, with one end closed, is inserted vertically with the open end down, into a tank of water until the open end is si . Assume that atmospheric pressure is 101.5 kPa. Neglecting Vapor pressure, how far will the water level in the tube be b he tank?

4m long, with one end closed, is inserted vertically with the open end down, into a tank of water until the open end is si . Assume that atmospheric pressure is 101.5 kPa. Neglecting Vapor pressure, how far will the water level in the tube be b he tank?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

: Determine the rate of flow of water through a pipe 300 mm diameter placed in an inclined position where a Venturimeter is inserted having a throat diameter of 150 mm. The difference of pressure between the main and throat is measured by a liquid of sp. gravity 0.7 in an inverted U-tube which gives a reading of 260 mm. Elevation difference between sections 1 and 2 is 1.0m.
Water flows upwards through a venturi section. The venturi section varies indiameter from 15cm at the top and bottom to 5cm at the narrowest point. A differential pressuretransducer measured a pressure difference of 43kPa. Assuming steady flow, determine the velocity ofthe flow through the narrowest region and the discharge through the meter. Assume that water has adensity of 1g/cm 3 .b) The discharge through the venturi section
The diving bell has the shape of a frustum of a cone (circular) with a closed flat top and open bottom. It is lowered from the outside air into salt water (ɣ= 10.2 kN/m3). Compute the gage pressure at the bottom of the caisson when the water level has risen 2.50m inside? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa Decimal Places required in the final answer: 3
(a) Determine the height water at 70F will rise due to capillary action in a clean, 1/4-in.-diameter tube. (b) What will be the height if the diameter is reduced to 0.01 in.? At this temperature, water = 0.00497 lb/ft and water = 62.3 lb/ft3 . Use  = 0degrees
Water flows upwards through a venturi section. The venturi section varies indiameter from 15cm at the top and bottom to 5cm at the narrowest point. A differential pressuretransducer measured a pressure difference of 43kPa. Assuming steady flow, determine the velocity ofthe flow through the narrowest region and the discharge through the meter. Assume that water has adensity of 1g/cm 3 .c) Is the fluid pressure at the bottom of the venturi section greater than, less than, or equal to the fluidpressure at the narrowest region?
1. The horizontally lying device or fitting shown below connects three pipelines. Water (γwater = 9.81 kN/m3 ) enters the device through A with a speed VA = 8 m/s and a pressure PA = 70 kPa . Water exits through C at 9 m/s. Friction and minor head losses through the device are negligible. Note that B and C are not at atmospheric pressure. (a) Calculate the speed and flow rate of the water at B. Is the water flowing through B flowing into to the device or out of the device? (b) Calculate the pressures at B and C, PB and PC.
The statistic pressure head in an air pipe is measured with a piezometer as 16 mm. of water. A pitot probe at the same location indicates 24 mm. of water. Calculate the velocity of the 20°C air. Also, calculate the mech. no.
Water flows upwards through a venturi section. The venturi section varies indiameter from 15cm at the top and bottom to 5cm at the narrowest point. A differential pressuretransducer measured a pressure difference of 43kPa. Assuming steady flow, determine the velocity ofthe flow through the narrowest region and the discharge through the meter. Assume that water has adensity of 1g/cm 3 .a) The mean fluid velocity through the narrowest region
Refer to Fig. P5.4. Water at 10°C flows up AB (5 m long, 40 mm diameter),then along BC (3 m long, 30 mm diameter). The measured pressure at A is 275kPa. (a) Find the pressure at C if the flow rate is 2.0 L/s. Neglect pipe frictionand energy losses. 6) Repeat for the same flow rate in the opposite direction.Table A.1 for water at 10°C: y = 9.804 kN/m².Vertical
The rectangular bin with an inclined gate AB is filled with water to the depth shown. Determine the location in meters along with the inclination of the center of pressure from the water surface when the total pressure is acting on gate AB x=0.82 a=2.02 m b=30 degrees asap 15 mins
3. Attached photo for the problem Sharp edge orifice... (my answer was -2.43) 4. A 50 mm diameter siphon discharges water from a reservoir (Point 1 elev = 20m) into open air (Point 3 elev. 10m). The head loss from the reservoir (point 1) to the summit (point 2 elev = 22m) is 3 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. Determine the velocity in the siphon in m/s? Photo for this problem is attached below.
he 30o directional pressure pipe elbow in the vertical plane is 60 cm in diameter. from the elbowThe flow rate of the current passing is 1 m3/s. At the lower end (1) of the elbow, the pressure is 70 kPa and the ground level is 30 m, the upperAt the end of the section (2), the ground level is 31 m. The fluid is water (ρwater=1000 kg/m3), frictionless and incompressible.taking into account thata) Find the velocities in sections (1) and (2) and the pressure in section (2).b) The weight of the pipe at the elbow is 1400 N. In case the length between sections is 1.2 mIn order to keep the elbow stable, taking into account the mass of water in the elbow, in the vertical directionCalculate the force that must be applied.