Q2. In The following, the instructions are dependent on each other, if A = B8 H. and Cy 1, next to each instruction write down the content of the Accumulator IN hex and the Carry after the instruction has been executed: %3D 1. RR A 2. RRC A 3. RL A 4. RLC A 5. RR A 6. RL A 7. SWAP A

Q2. In The following, the instructions are dependent on each other, if A = B8 H. and Cy 1, next to each instruction write down the content of the Accumulator IN hex and the Carry after the instruction has been executed: %3D 1. RR A 2. RRC A 3. RL A 4. RLC A 5. RR A 6. RL A 7. SWAP A

Name: Q2. In The following, the instructions are dependent on each other, i
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: Q2. In The following, the instructions are dependent on each other, if A B8 H.and Cy 1, next to each instruction write down the content of the Accumulator INhex and the Carry after the instruction has been executed:%3D1. RR A2. RRC A3. RL A4. RLC A5

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

What will be the contents of BX after the following instructions execute?mov bx,5stcmov ax,60hadc bx,ax
What is the following instruction equivalent to? addiu $t2, $t3, 7 A. $t2 + $t3 = 7 B. $t2 = $t3 & 7 C. $t2 = $t3 + 7 D. $t3 = $t2 + 7
9. please make the given code according to given below instruction in a very easy manner dont copy it from somewhere and paste. also share the screenshots of code and output.
Answer the following questions based on the figure below.(a)Give the hexadecimal representation of “beq x10,x0,L1”.(bAssume the program executes to “jal x1,4”. What is the next instruction to execute? (c)Use lui or auipc to write a sequence of instructions to jump from the memory location 0x0000000020000000 to execute “beq x10,x0,L1” in the figure. Show the memory locations of your instructions and explain your code. You cannot use more than 3 instructions and can only use RV64I instructions.
If R1 contains ×FFFF and R2 contains ×0000, then what are the condition code values after the following instruction is executed? 0001 011 001 0 00 010 A) N is [ 0 or 1]? B) Z is [ 0 or 1]? C) P is [ 0 or 1]?
FILL IN THE BLANKS ? (8) After the instructions MOV AX, 2500H and ADD AX, 2300H have been executed in sequence, find the status of SF= 【16】, AF= 【17】 and ZF= 【18】.
18. Let S and Q be two semaphores initialized to 1, where P0 and P1 processes the following statements wait(S);wait(Q); ---; signal(S);signal(Q) and wait(Q); wait(S);---;signal(Q);signal(S); respectively. The above situation depicts a _________ . a. Semaphore b. Deadlock c. Signal d. Interrupt
Examine the following program and find the time delay in seconds. Exclude the overhead due tothe instructions in the loop. MOV TMOD, #10H ; MOV R3 , #200 ;AGAIN: MOV TL1 , # 08H ; MOV TH1, # 01H ; SETB TR1 ;BACK: JNB TF1 ,BACK ; CLR TR ; CLR TF1 ; DJNZ R3 ,AGAIN ;
Translate the following LEGv8 code to C. Assume that the variables f, g, h, i, and j are assigned to registers X0, X1, X2, X3, and X4, respectively. Assume that the base address of the arrays A and B are in registers X6 and X7, respectively. ADDI X9, X6, #8 ADD X10, X6, XZR STUR X10, [X9, #0] LDUR X9, [X9, #0] ADD X0, X9, X10
Assume that the program counter (PC) is set to 0x00000000. Describe how each of the instructions below could be used to set the next value of PC to 0x0FFFFFFC: j beq, jr, jal, bne Please do not just define what each instruction does and please do not give a random example thanks
W rite a MIPS program to continuously generate the following series of integers: 1, 2, 3, 6, 9, 18, 27, 54, 81, and so on. Use standard MIPS programming conventions. Use the jump instruction to generate an infinite loop. Write a subroutine EVEN that returns a 1 if the argument is even, else it returns a 0. You must call this subroutine with jal and return from it with jr. Dont use any .data, .word, .text, or .globl commands or li. No hand written and fast answer with explanation
(a) Find the value of AX and EAX registers.dataarrayW WORD 7000h,8000h,9000harrayD DWORD 1,2,3,4.codemov ax,[arrayW+2] ; AX =mov ax,[arrayW+4] ; AX =mov eax,[arrayD+4] ; EAX =(b) write a program that adds the following three bytes:.datamyBytes BYTE 80h,66h,0A5h