Q2c) Listed in the table below is the tensile stress-strain data for different grades of steels. Utilizing the data given answer the three queries given below.MaterialYield StrengthTensileStrain atFractureElasticStrengthFractureStrength (MPa)Modulus(MPa)(МPa)(GPa)A41014400.63265410B2002200.401052508159500.255006108006500.14720210EFractures before yielding6505501) Which will experience the greatest percent reduction in area? Why?2) Which is the strongest? Why?3) Which is the stiffest? Why?

A) the material which will show highest elongation, will show the greatest percentage reduction in…

Q2c) Listed in the table below is the tensile stress-strain data for different grades of steels. Utilizing the data given answer the three queries given below. Material Yield Strength Tensile Strain at Fracture Elastic Strength Strength (MPa) Fracture Modulus (MPa) (MPa) (GPa) A 410 1440 0.63 265 410 B 200 220 0.40 105 250 815 950 0.25 500 610 D 800 650 0.14 720 210 Fractures before yielding 650 550 1) Which will experience the greatest percent reduction in area? Why? 2) Which is the strongest? Why? 3) Which is the stiffest? Why?

Q2c) Listed in the table below is the tensile stress-strain data for different grades of steels. Utilizing the data given answer the three queries given below. Material Yield Strength Tensile Strain at Fracture Elastic Strength Strength (MPa) Fracture Modulus (MPa) (MPa) (GPa) A 410 1440 0.63 265 410 B 200 220 0.40 105 250 815 950 0.25 500 610 D 800 650 0.14 720 210 Fractures before yielding 650 550 1) Which will experience the greatest percent reduction in area? Why? 2) Which is the strongest? Why? 3) Which is the stiffest? Why?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An application requires ultimate tensile strength and yield strength ofa steel at 110 ksi and 91 ksi, respectively. Answer the following 4 questions:4.1. Can SAE 1040 steel be selected for this application?4.2. If “no” is the answer in Part I, the following Part II, III, and IV can beignored. If “yes” is the answer in Part I, which condition of SAE 1040 shouldbe selected?4.3. Why is that steel with the condition in part II selected?4.4. Is the selected steel brittle or ductile? and Why?
As the tempering temperature of a heat treated steel increases the associated values of Brinnell hardness also increase, while the values of tensile strength and yield strength decrease. True or false
Fatigue data of steel is showed in the following stress-cycle curve.Write down the values of steel endurance limit and steel fatigue strength at 10^5 cycles in the spaces provided below.Steel Endurance Limit: _____ ksiteel Fatigue Strength at 10^5 cycles: _____ ksi
Q24. What is toughness of a material? Is it the same as hardness? Is it also measured in pascals? 3 Q25. What is brittle transition temperature? 2 Q26. What is the risk of using steels at temperatures above 350O?
An application requires ultimate tensile strength and yield strength ofa steel at 110 ksi and 91 ksi, respectively. Answer the following 4 questions: Can SAE 1040 steel be selected for this application? If “no” is the answer in Part I, the following Part II, III, and IV can beignored. If “yes” is the answer in Part I, which condition of SAE 1040 shouldbe selected? Why is that steel with the condition in part II selected? Is the selected steel brittle or ductile? and Why?
Please include the free body diagram a)What is the elongation in bronze? 0.191456 in0.18125 in0.2872 in0.071796 in b)What is the elongation in Steel? 0.191456 in0.18125 in0.071796 in0.2872 in c)Vertical displacement of load P? 0.18125 in0.2872 in0.191456 in0.071796 in
Which steel presents the maximum modulus of toughness UT? UT = ( (Sy − Sut) /2 ) ε f AISI 4142 and AISI 1020 AISI 1020 AISI 1095 and AISI 1020 AISI 4142 and AISI 1095
Draw a Stress/Strain graph of a mild tensile steel and identify the limit of proportionality and the yield point
Please match different stresses to the stress value corresponding to the different points on the Stree-strain diagram of a low carbon steel. Proportional Limit Ultimate Strength Tensile Yield Strength A. A B. B C. D
Using various tables, determine the specific strength (yield strength-to-density ratio) in unit of kN⋅m/kg for AISI 1015 hot-rolled steel, 7075-T6 aluminum alloy, Ti-0.2 Pd titanium alloy, and ASTM No. 60 gray cast iron.
Q1a) A sample of an aluminum alloy has a tensile strength of 275 MPa, What will be the maximum force that can be withstood by a rod of that alloy with a cross-sectional area of 2.09 cm2?
Sketch the relationship between the stress and the number of cyclic loading applied on an element