Q3 13(b) XOR output=0, flip-flop Q=0, from I/O input-1, MUX 1 select=1, MUX 2 select=0, MUX 3 select=1, MUX 4 select=0, and MUX 5 select=1. ines PIA 0000 15 expander product terms from other macrocells Product- term selection matrix Shared expander Parallel expanders from other macrocells во Global Global clear clock MUX 2 Voc MUX 1 MUX 3 MUX 4 PRE DIT C EN CLR O MUX S From 1/0 -To 1/0

Q3 13(b) XOR output=0, flip-flop Q=0, from I/O input-1, MUX 1 select=1, MUX 2 select=0, MUX 3 select=1, MUX 4 select=0, and MUX 5 select=1. ines PIA 0000 15 expander product terms from other macrocells Product- term selection matrix Shared expander Parallel expanders from other macrocells во Global Global clear clock MUX 2 Voc MUX 1 MUX 3 MUX 4 PRE DIT C EN CLR O MUX S From 1/0 -To 1/0

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef
Draw logic diagram for half adder and full adder circuit using Logisim Software
By using the design procedure for digital computers, design the following:i. Encoderii. Decoderiii. 4-bit comparator
Write an assembly 8051 code to count a hexadecimal digit every second and display it on the 7-segment.
Problem #4: Consider the Programmable Array Logic PAL module below '1' A B C D F₁ F2 F3 1. Determine the corresponding product term per row PRODUCT TERMS 000000
Design the interfacing circuit shown below and write a program to display single digit (between 0 and 9) prime numbers followed by even numbers, the next odd numbers and repeats in 7-segment displays and its equivalent 8-bit binary value in LEDS. a) When displaying Prime numbers, the first 7-segment display must show "P" and the second 7-segment display must show prime numbers one by one b) When displaying Even numbers, the first 7-segment display must show "E" and the second 7-segment display must show even numbers one by one c) When displaying Odd numbers, the first 7-segment display must show "O" and the second 7-segment display must show even numbers one by one
Design a counter that counts 1-2-3-5-7 Please explain the following:state diagram state table simplification Logic circuit digital design
How many states required to design an FSM machine to process the following sequence, 000111000 6. 6. 3
Design a logic circuit for decoder that accepts 3-bit input and displays alphabet “048” at the seven- segment as illustrated at Figure 1 (a). The input-output mapping shown in Table 1 (a). Refer Figure 1(b) and Figure 1(c) for seven-segment display format showing arrangements of segments using common anode connection. Show each steps clearly to produce the expressions and required design. [Rekabentuk litar logik untuk penyahkod yang menerima input 3-bit dan paparkan abjad "048" di tujuh-segmen seperti digambarkan pada Rajah 1(a). Pemetaan masukan-keluaran ditunjukkan dalam Jadual 1(a). Rujuk Rajah 1(b) and Rajah 1(c) untuk format paparan tujuh-segmen yang menunjukkan susunan segmen menngunakan sambungan 'common anode'. Tunjukkan setiap langkah dengan jelas untuk menghasilkan ungkapan dan reka bentuk yang dikehendaki.] Xs X6 X7 DECODER Figure 1(a) [Rajah 1(a)] a b с d e f g a 80123456789 Figure 1(c) [Rajah 1(c)] g Figure 1 (b) [Rajah 1(b)] b с DP
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
Design a combinational circuit with the four inputs A,B.C, and D, and three outputs X, Y, and Z. When the binary input is odd number, the binary output is one lesser than the input. When the binary input is even number the binary output is one greate than the input. Implement the function using multiplexers with minimal input and select line.
1. Consider the CRC generator shown below. Determine the output of the CRC circuit (i.e. Q4 Q3 Q2 Q1 Q0, expressed as a decimal number) for the input sequence "1010" (input one bit at a time, left to right). Assume the CRC circuit is initialized to state 11111. D Q0 Q2 Q4 Q1 Q3 Clock - Data In