Q3: A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located at (C). The first output gear (B) takes (15 kw) and the remaining power delivered to the second gear at (A) . If the modules of elasticity E=200 Gpa and 0.3 poison ratio. Calculate the

Q3: A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located at (C). The first output gear (B) takes (15 kw) and the remaining power delivered to the second gear at (A) . If the modules of elasticity E=200 Gpa and 0.3 poison ratio. Calculate the

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.10P: What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm,...

See similar textbooks

Related questions

Q: A steel shaft with constant diameter of 50 mm is loaded as shown in the figure by torques applied to…

Q: The shaft in the figure below is part of a drive for an automated transfer system in a metal…

Q: Figure Q3 (b) shows a steel transmission shaft with 500 mm length and external diameter of 40 mm.…

A: from the torque equation: TJ=τr=GθLθ=TLGJ for the same material G will be same.…

Q: For your final design project, you use a keyway to hold your gear on the shaft. The radius of the…

Q: diameter, and the distance from the center of the rudder stock to centerline of rams is 800 mm.…

Q: PROBLEM 2. The turbine in the figure generates 90 kW power. 50 kW of power is drawn from the gear at…

A: Given Data: The power generated by the turbine is P=90 kW. The power generated by gear C is PC=50…

Q: Four gears are attached to a circular shaft and transmit the torques shown in the figure. The…

A: Allowable shear stress in the shaft, τallpwable=10000 psiInside diameter of hollow shaft, d=1.0 in

Q: maximum shear stress that is generated through the shaft.

Q: Figure 4 shows a 50mm diameter solid shaft made out of steel whose modulus of rigidity is 75,000…

Q: In the gear system of Figure 4, a torque of 5 N-m is applied on gear E. Shaft (1) and shaft (2) are…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Four gears are attached to a circular shaft and transmit the torques shown in the figure. The…

A: Data given Allowable shear stresses = 10000 psi b) inside diameter = 1.4 in

Q: The diameters of the solid shafts in the gear wheel set shown in the figure are dAB = 20mm, dCD =…

A: maximum shear stress = =90 MPa For angular rotation, modulus rigidity a length as assumed (not…

Q: 1) A pair of cast iron bevel gears connect two shafts at right angles. The pitch diameters of the…

A: Given:…

Q: The input shaft to a gearbox, shown in Figure 3, operates at a speed of n1 and transmits a power of…

Q: Gear 2 (pinion) runs at 1800 rpm ccw and transmits 3.5 kW to frictionless, idler gear 3. The…

A: Note- As per our company's guidelines we are allowed to answer first three subparts in case of…

Q: Q4-A shaft (55 mm) diameter is transmit power of 200 W at 1200 rpm, the maximum shear stress of (80…

A: Given data: - The diameter of the shaft is d = 55 mm. The power transmit is P = 200 W. The speed of…

Q: 2- The four gears shown in the below Fig. are attached to a 50- mm diameter steel shaft. Compute the…

Q: The rotation in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 10 mm in radius and…

A: Given: The shaft length, L = 800 mm = 0.8 m The torque applied, T = 80 N.m The radius of shaft, r =…

Q: A propeller shaft C having a diameter of 75 mm is mounted on two bearings B1 and B2 and is driven by…

A: Helical gear In helical gear the teeth of helical gears are cut in the form of a helix on the pitch…

Q: Form the figure below, the power transmission shaft shows the forces acting on it carrying two…

Q: shaft made of steel receives 7.5 kW power at 1500 r.p.m. A pulley mounted on the shaft as shown Fig.…

Q: "B -LBC- -LcD A solid steel shaft ABCDE (see Fig.) having diameter d = 35 mm turns freely in…

A: Given data: The diameter of the shaft is d=35 mm=0.035 m The torque at the gear C is T2=425 Nm The…

Q: The small gear of an internal gear train shown in the figure is powered by a 500-kW motor at 30 Hz.…

A: Given data:

Q: An engine develops 5.0 MW at 115 RPM and the ratio of maximum to mean torques is 1.3 to 1. Calculate…

Q: Problem : A train of spur gears with 20°full-depth involute teeth is shown in the Figure below. Gear…

A: Here Given Power P=5000 WattN1=720 rpmT1=20T2=50T3=30T4=60m=4mmϕ=20°Radius of…

Q: A compound shaft drives three gears, as shown. Segments (1) and (2) of the compound shaft are hollow…

A: Given Data For the segment 1 and 2., The shear modulus is:G=6500 ksi The outside diameter…

Q: Figure Q1 shows a solid steel shaft AF which is supported by frictionless bearings at B and F. It is…

Q: A gear is fixed on a shaft through a tight assembly. The diameters of the gear and shaft at the…

A: Given data: GeardG=50-0.030-0.015ShaftdS=50+0.012+0.022 Need to determine the maximum radial…

Q: A solid 1.6 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant.…

Q: 20° pressure angle. Gear 3 is an idler (b) Find the torque T4c that gear 4 exerts on shaft c.

A: Calculate the speed of the shaft in rad/sec. Here, the speed of the shaft in rev/min is .…

Q: Figure Q6 shows a circular shaft AB and a square shaft BC where it is fixed at C. a. Determine the…

A: Given : Torque = 2000 N.m The length of shaft AB = 600 mm The length of shaft BC = 600 mm The…

Q: A solid circular shaft AB of length 504 mm is fixed against rotation at both ends as shown in fig.…

A: Given data: LAB = 504 mm dAC = 41 mm dCB = 62 mm…

Q: pulleys at -ach 400 mm ring and are own below. e shear stress of Pa, calculate the d for this raw…

Q: A compound shaft drives three gears, as shown in Figure P6.14. Segments (1) and (2) of the shaft are…

A: From the given data,

Q: Gear B, shown in Figure Q4, supplies 15 kW of power, while gears A , C and D withdraw 6 kW, 4 kW and…

Q: A 1018 steel wedge will be created with Sy = 63 Kpsi and a factor of safety of 1.5. The axis where…

Q: A carbon steel shaft AB is fixed with two gears and is applied with 4 torque as shown in Figure 1.…

A: Considering torque in counterclockwise direction when looked from B to A as positive value, Given,…

Q: A transmission shaft supporting a spur gears B and the pulley D is shown in Fig. 1. The shaft is…

Q: The four gears are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of…

Q: A transmission shaft supporting a spur gears B and the pulley D is shown in Fig. 1. The shaft is…

A: Given data,P=20KWN=500 rpmP1=3P2Pr=Pttan 20°Sut=700N/mm2Syt=460N/mm2Kb=kt=1.5

Q: Problem : A train of spur gears with 20°full-depth involute teeth is shown in the Figure below. Gear…

A: given; φ=200power(P)=50Kwspeed(N)=300rpmSyt=380MPaFOS=2diameter of shaft(d)=?

Q: A conveyor belt is driven by a 8-hp motor turning at 2,500 rpm. Through a series of gears that…

A: Given:Power of motor,P=8HP=(8×745.7)W=5965.6WSpeed of motor,N=2500rpmSpeed of belt drum motor…

Q: A steel shaft is transmitting 50 Hp at 1200 rpm. The nature of load and type o service of the shaft…

Q: Four gears are attached to a circular shaft and transmit the torques shown in the figure. The…

A: Data given- Allowable shear stress = 18000 psi .

Q: A solid 1.2 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant.…

Q: The figure below shows a boat propeller mounted on a drive shaft with a 7 mm diameter (d)…

A: Given: Diameter of the pin d=7mmDiameter of the drive shaft D=69mmYield stress σy=427MPaUltimate…

Q: A steel shaft with constant diameter of 50 mm is loaded as shown in the figure by torques applied to…

Q: A compound shaft drives three gears, as shown. Segments (1) and (2) of the compound shaft are hollow…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

Q3: A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located
at (C). The first output gear (B) takes (15 kw) and the remaining power delivered to the
second gear at (A) . If the modules of elasticity E=200 Gpa and 0.3 poison ratio. Calculate the
shearing stress at each section and the total angle of rotation between C and A. Knowing that
the shaft rotates at 6 Hz.
B
55 mm o
65 mm
Fig 3
4 m
2 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
The steel axle of a large winch on an ocean liner is subjected to a torque of 1.65 kN · m (see figure). What is the minimum required diameter dminif the allowable shear stress is 48 M Pa and the allowable rate of twist is 0.75º/m? (Assume that the shear modulus of elasticity is 80 G Pa.) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d/8, Compare dminvalues to corresponding values from part (a)
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
When drilling a hole in a table leg, a furniture maker uses a hand-operated drill (see figure) with a bit of diameter d = 4.0 mm. If the resisting torque supplied by the table leg is equal to 0.3 N · m, what is the maximum shear stress in the drill bit? If the allowable shear stress in the drill bit is 32 MPa, what is the maximum resisting torque before the drill binds up? If the shear modulus of elasticity of the steel is G = 75 GPa, what is the rate of twist of the drill bit (degrees per meter)?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A motor supplies a torque of 5.5KNm to the constant diameter steel (G= 80GPa) line shaft shown in the figure. Three machines are driven by the gears B, C, and D on the shaft, and they required torques of 3.0KNm, 1.5KNm, and 1.0KNm, respectively. Determine: a. The minimum diameter required if the maximum shearing stress in the shaft is limited to 100MPa.b. The rotation of gear D with respect to the coupling at A if the coupling and gears are spaced at 2m intervals and the shaft diameter is 75mm.