Q3 (a) State advantage and disadvantage of delta-connected three-phase voltage source compare to the Y-connected system. A balanced three-phase delta connected source supplies to a balance three-phase star connected load, consider the phase sequence is ABC. The load has impedance for each phase is 4 +j3 A and phase voltage of VAN=75236.86° V (b) (i) Sketch the circuit diagram of the system. |

Q3 (a) State advantage and disadvantage of delta-connected three-phase voltage source compare to the Y-connected system. A balanced three-phase delta connected source supplies to a balance three-phase star connected load, consider the phase sequence is ABC. The load has impedance for each phase is 4 +j3 A and phase voltage of VAN=75236.86° V (b) (i) Sketch the circuit diagram of the system. |

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.24MCQ: It is stated that (i) balanced three-phase circuits can be solved in per unit on a per-phase basis...

See similar textbooks

Similar questions

A balanced delta-connected lood with impedance per phase of 30<30 ohms is connected to an abc-sequence balanced three-phase source with eAC = -120√2 cos (120πt + π/6) V through conductors with negligible impedances. Determine the line currents, load phase currents and the total complex power drawn by the lood. Write your values in polar form.
6. An abc-sequence, three-phase, 4-wire, 380-V supply is connected to an unbalanced load having phase impedances of: Za = 8 + j6 ohms, Zb = 8 - j6 ohms and Zc = 5 ohms. Impedance of the neutral wire is 0.5 + j1 ohms. Line impedance is 1+ j2 ohms per phase. Find the value of the neutral current in polar form.
In a balanced 3-phase system, the effective value of the IbB current for a triangular connected load is known as 15 (-150 degrees) Amperes and the effective value of the VCA voltage is known as 60 (90 degrees) Volts. Since it is known that the phase sequence is positive; Phase current IAB= 8.660 (60 degrees) A Phase current IAC= [Select ] Load impedance Z= [Select ] the total average power sent to the 3 phase load is Pt Aggregate= [Select ] (Note: Perform your operations using at least 3 digits after the comma.)
low voltage systems In the circuit given below, single-phase powers connected to the single-phase network are given. If the effective value of the applied voltage is 220 V, the amplitude of the current drawn from the network(I) how many A?(Note: - sign indicates phasor state) A)142,85 B)119,34 C)129,16 D)137,86
1. A 69-kV, three-phase short transmission line is 16 km long. The line has a per phase series impedance of 0.125+j0.4375 Ω per km. Determine the sending end voltage, voltage regulation, the sending end power, and the transmission efficiency when the line delivers (a) 70 MVA, 0.8 lagging power factor at 64 kV. (b) 120 MW, unity power factor at 64 kV. Use lineperf program to verify your results. 2. A three-phase, 765-kV, 60-Hz transposed line is composed of four ACSR, l,431,000-cmil, 45/7 Bobolink conductors per phase with flat horizontal spacing of 14 m. The conductors have a diameter of 3.625 cm and a GMR of 1.439 cm. The bundle spacing is 45 cm. The line is 400 km long, and for the purpose of this problem, a lossless line is assumed. (a) Determine the transmission line surge impedance Zc, phase constant ß, Wavelength, the surge impedance loading SIL, and the ABCD constant. b) The line delivers 2000 MVA at 0.8 lagging power factor at 735 kV. Determine the sending end quantities and…
The line voltage Vab at the terminals of a connected balanced three-phase load at Δ is ??? = 4160∠0° V. The line current IaA is ??? = 69.28∠ − 10° A. a) Calculate the load impedance per phase if the phase sequence is positive (ABC). b) Repeat question (a) for a negative phase sequence (CBA).
single circuit three-phase line, 60 Hz, 18 km has a total resistance and inductive reactance of 4.242 ohm and7.451 ohm per phase respectively. The line delivers 2500 kW to a balanced load at 11 kV. (1) determine the sending-end voltage when the power factor is (i) 80% lagging, (i) unity, and (ii) 90 % leading, (2) draw the phasor diagrams of the line at the above (3) determine the voltage regulation of the line at the above power factors.
A balanced delta-connected load has phase impedances of 4+j3 Ohms. It is connected to balanced transmission lines, with Vab = 1.5kV @ 15 degrees. a) What is the current through each of the load phases? b) What is the current through each of the transmission lines? c) Which ACSR cable should be used for these transmission lines to give a 20% current rating margin for this load?
In a balanced three-phase Y-Y connection system, the phase sequence of the source voltages is given as abc. Calculate the impedance of the three-phase load given that Van = 120<40° (phasor)Vrms and a-phase line current and line impedance are 7.10<-10.28°(phasor) Arms and 0.8 + j1 Ω, respectively.
A 400V three-phase, four wire system has the following loads connected: Phase 3: load impedance Z3 = 15 – j20 Ω Draw the circuit diagram and determine: The line and phase voltages for phase 3 (including phase angles) The line and phase currents for for phase 3 (including phase angles) The neutral current (including phase angle)
A Y-Y three-phase system has a source of 380 V and a load of impedance of 6+j5 Ohm/phase through a transmission line of 2+j 1 Ohm/phase.Plot this Y-Y three-phase system then calculate complex power supplied by the source.
One advantage of balanced three-phase systems over separate singlephase systems is reduced capital and operating costs of transmission and distribution. (a) True (b) False