I need the answer as soon as possible Q3: Find the diameter of a circular orifice to discharge (0.015m/sec) under a head of(2.4m). If the orifice is in a vertical plane and the jet falls (0.25m) in a horizontaldistance of (1.3m) from the vena-contracta. Find the head loss through the orificeand Ce (Take Ca= 0.6).

Answered: Image /qna-images/answer/63d994c6-fcdb-47fb-a2ee-a842b7cc6059.jpg

Answered: Q3: Find the diameter of a circular…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

B Refer to, Fig. X5.2.2. Assume a = 1 m, b = 4 m, and the flow to be frictionless in the siphon. Find the rate of discharge in mºls and the pressure head at B if the pipe has a uniform diameter of 150 mm. M Tar N
The pressure gage leading to the turbine casing of a Francis turbine reads 0.5 MPa and the center of the spiral casing is 5 m above the tailrace. What is the net head if the velocity of the water entering the turbine is 10 m/s?
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolutepressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa (indicate the sign if negative) Decimal Places required in the final answer: 3
For the siphon in Fig. 6.26, calculate the distance X re-quired to obtain a volume flow rate of 7.1 X 10-3m³/s.
The waterwheel in Fig. is being driven at 200 r/minby a 150-ft/s jet of water at 20 ° C. The jet diameter is 2.5 in.Assuming no losses, what is the horsepower developed bythe wheel? For what speed Ω r/min will the horsepowerdeveloped be a maximum? Assume that there are manybuckets on the waterwheel.
Aa certain hydro-power station has a head of 500m between the upper and lower reservior. A. Determing the approach velocity of water as it enters the turbine ; B. If the volume flowrate is 60cumec, what is the diameter of the penstock; and C. If the head loss due to friction represents 10% of the static head in (a) determine the actual velocity approach and the corrected diameter of the penstock required
A centrifugal pump having a head-capacityrelationship given by the equation ha=180 –6.10 X 10-4 Q2, with ha in feet when Q is ingpm, is to be used with the system shownin the figure, For Z2-Z1= 50 ft, what is theexpected flowrate if the total length ofconstant diameter pipe is 600 ft and thefluid is water? Assume the pipe diameter tobe 4 inch and the friction factor to be equalto 0.02. Neglect all minor losses.
At point A where the diameter at of the pipe is 18 cm the pressure reading is 22.5 cm of Mercury. At point B, 3 m lower than A, the diameter is 48 cm and the pressure reading is 50 cm of Mercury. If the total head loss between the two points is 1.50 m, solve for the discharge. Water is flowing through the pipe. subject: hydraulics
Here, 20 degree celcius water is being siphoned from a reservoir, see attached image. What would be the minimum flow rate be, without cavitation occuring in the system at points 2 and 3?
A liquid with a specific gravity of 1.26 is being pumped in a pipeline from A to . At A, thepipe diameter is 60cm and the pressure is 300kN/m2 . . At B, the pipe diameter is 30cm and thepressure is 330kN/m2.. Point B is 1.0m lower than A. Find the flow rate if the pump puts 16kWinto the flow. Neglect head loss.
Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m /s. At point A in the pipe the pressure is 210 kPa. At B, 4.57 m above A, the diameter is 600 mm, and the lost head A to B equals 1.83 m. Determine the pressure at B. indicate the free body diagram
A pump was installed with a suction head of 6 meter and a discharge head of 10 meters. The discharge rate of the pump is 60 liters per minute. What is the water horsepower of the pump?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Q3: Find the diameter of a circular orifice to discharge (0.015m/sec) under a head of (2.4m). If the orifice is in a vertical plane and the jet falls (0.25m) in a horizontal distance of (1.3m) from the vena-contracta. Find the head loss through the orifice