Q3: Find the series inductance required to put a 200 kVA, 220 V/40 has 10 % leakage reactance and 2% resistance on 200 kVA base into resonance condition. An object has to be tested at 500 kV using the above transformer at 50 Hz. If the charging current of the cable at 500 kV is 0.5 A, neglect dielectric loss of the object. And Assume 8 kQ resistance for the inductor to be used Also find the input voltage, input power to the kV test transformer transformer and losses of test transformer?

Q3: Find the series inductance required to put a 200 kVA, 220 V/40 has 10 % leakage reactance and 2% resistance on 200 kVA base into resonance condition. An object has to be tested at 500 kV using the above transformer at 50 Hz. If the charging current of the cable at 500 kV is 0.5 A, neglect dielectric loss of the object. And Assume 8 kQ resistance for the inductor to be used Also find the input voltage, input power to the kV test transformer transformer and losses of test transformer?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

c) If we consider the resistor, capacitor and inductor as the load connected to the twovoltage sources, at which frequency can the load be considered resistive (two decimalaccuracy required)? d) If we consider the resistor, capacitor and inductor as the load connected to the twovoltage sources, at which range of frequencies can the load be considered inductive(two decimal accuracy required)?
5/The Voltage Regulation of a Transmission Line (in the simulator) depends on which parameter/s? A. Both the Transmission Line Resistance and Inductance B. The Transmission Line Shunt Capacitance only C. The Transmission Line Inductance only D. The Transmission Line Resistance only
1. Discuss the influence of the bypass, coupling, internal, and stray capacitances on the frequency response.
Suppose that a network can be divided into two subnets connected by only two conductors, as shown below. Two points on these conductors are labeled a and b. The power factor seen to the right of a and b is defined as cos (ϕ) if ϕ is the angle formed by the phasor V and I. (Given the parity of the cosine, it does not matter if it is the angle by which V is advanced with relative to I or for the one that is delayed.) (Image 1) Now consider the following circuit, in which six points have been marked. (Image 2) a) Determine the power factor seen to the right of a3 and b3analyze your result. Does it make physical sense? What is happening to the currents in the inductor and in the capacitor? b) Determine the power factor seen to the right first of a2 and b2 and then of a1 and b1. Re-analyze your results. c) Calculate the capacitance that must be connected between a1 and b1 so that the power factor seen to the right of these points is 0.95 in lag. Assume the source frequency is 60 Hz.
a)We have a two-wire overhead transmission line, powered by a constant voltage source of 700 V. The values for the inductance of the conductors are 2.348x10-3 H/km and the capacitance values are 6.325x10-9 F/km. Assuming an ideal (no loss) line and its length at 130 km, determine the natural impedance of the line. b) What is the transient phenomenon in a transmission line? As an example of its causes.
The ratio of the inner conductor perimeter to the outer conductor perimeter of a coaxial cable is 0.4993 and how many structure capacitance pF/m is the insulated coaxial line?
a) Determine ?? ??⃗ and ?? ??⃗ using CDR. b) Sketch the phasor diagram for the currents.
Use the external excitation method for part a.
A lossy capacitor Cx, rated for operation of 5 kV, 50 Hz is represented by an equivalent circuit with an ideal capacitor Cp in parallel with a resistor Rp. Cp is 0.102 microF and Rp=1.25 Mohm. The power loss, and loss tangent of this lossy capacitor at rated voltage respectively ?
A transmission line with a characteristic impedance of 100 Ohm is used tomatch a 50 ohm section to a 200ohm section. If the matching is to be doneat 429 MHz and I GHz. The length of the transmission line can beapproximately.
Discuss the effect of adding a pole on the root locus shape, through the relative stability.
Could you please go more in depth about how to create the ac equivalant model? thank you