Q3: For Fig. 3, determine the tension in cable ABD and the reaction at support C. Q4: The 2-Mg uniform pole in Fig.4 is supported by a ball-and -socket joint and two cables. Determine the tension in cables AC and BD. Q5: Determine the horizontal and vertical components of reaction at the pin A and the reaction of the smooth collar B on the rod shown in Fig.5. 125 mm 450 b 300 175 mm 225 mm 150 N 75 Fig.3 Fig.5 Fig.4

Q3: For Fig. 3, determine the tension in cable ABD and the reaction at support C. Q4: The 2-Mg uniform pole in Fig.4 is supported by a ball-and -socket joint and two cables. Determine the tension in cables AC and BD. Q5: Determine the horizontal and vertical components of reaction at the pin A and the reaction of the smooth collar B on the rod shown in Fig.5. 125 mm 450 b 300 175 mm 225 mm 150 N 75 Fig.3 Fig.5 Fig.4

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.125P: The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A...

See similar textbooks

Similar questions

The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
Rod AD is acted upon by a vertical force P at end A and by two equal and opposite horizontal forces of magnitude Q at points B and C . Derive an expression for the magnitude Q of the horizontal forces required for equilibrium.
The cylinder as shown below weighs 1000 N. It is supported by a rod with a cable at point B. Determine the following: a.) The Tension at Point B. b.) The Reaction at Point A.
A 600-lb crate is supported by several rope-and-pulley arrangements as shown. Determine for each arrangement the tension in the rope. (See the hint for Prob. 2.66.)(Reference to Problem 2.66):A 200-kg crate is to be supported by the rope-and-pulley arrangement shown. Determine the magnitude and direction of the force P that must be exerted on the free end of the rope to maintain equilibrium. (Hint: The tension in the rope is the same on each side of a simple pulley. This can be proved by the methods of Chap. 4.)
A straight, uniform bar weighing 60lb rests in a horizontal positon between two frictionless slopes. A concentrated load of 200lb acts at distance x from the right hand slope. Determine x and reaction forces assuming that the bar is in static equilibrium.
A uniform circular rod with a weight of 8 lb and radius of 10 in. is attached to a pin at C and to the cable AB . Determine (a) the tension in the cable, (b) the reaction at C.
a) Draw a free body diagram of bar CBD. b) Determine the spring force, the tension in cable AB, and the support reaction(s) at D.
The bar shown is in equilibrium determine the forces P, T and R
A right circular roller of weight W rests on a smooth horizontal plane and is held in position by string AC as shown below The roller is pulled by a horizontal force P applied to its centre. Find the reaction at B and the tension of the string in the form of P and W
Engineering Mechanics (Equilibrium): The homogeneous 40 kg basr ABC is held by a horizontal rope attached to end C. Neglecting friction, determine the tension in the rope.
Engineering Mechanics (Equilibrium): The homogeneous 600lb plate is suspended from the three cables. Determine the tension in each cable
Question 1 Member ABC of negligible weight is supported by a pin and bracket at B and by an inextensible cord attached at A and C and passing over a frictionless pulley at D. For the loading shown and neglecting the size of the pulley, calculate the tension in the cord ,the horizontal and vertical reactions at point B.