Q7 The below graph is for Otto engine cycle 3 compression ratio r = v]/v2 = 8 state 1 =100 kPa, 300K qin. adiabatic so0 |KJkg (processes 2 P yk = const Qout r = 8 specific volume By using Cv, Cp and K of Air at 900K, calculate the following a) the temperature and pressure of the air at the end of each process b) the net work output/cycle [kJ/kg], and c) the thermal efficiency [nth] of this engine cycle

Q7 The below graph is for Otto engine cycle 3 compression ratio r = v]/v2 = 8 state 1 =100 kPa, 300K qin. adiabatic so0 |KJkg (processes 2 P yk = const Qout r = 8 specific volume By using Cv, Cp and K of Air at 900K, calculate the following a) the temperature and pressure of the air at the end of each process b) the net work output/cycle [kJ/kg], and c) the thermal efficiency [nth] of this engine cycle

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

HANDWRITTEN AND FINAL ANSWER MUST BE IN ENGLISH UNITS. Show solution. An experimental gas turbine engine is under development to increase its mechanical efficiency. It has a turbine efficiency of 95% and compressor efficiency of 85%. The following parameters are provided: P1 = 550 kPa, T1 = 25 deg C, rp = 5.5, T3 = 1450 deg C, Wnet = 5500 kW. Compute for the (a) flow rate and (b) mean effective pressure. Consider Ethane as your working fluid.
A two stage compressor with first stage piston displacement of 94,390 cm3/sec is driven by a motor. Motor output is 35 HP, suction temperature is 22 °C, volumetric efficiency is 85%, mechanical efficiency is 95%, the intercooler pressure is 30 psi gage. Air temperature in and out of the intercooler are 105 °C and 44 °C. Final discharge pressure is 100 psi gage, suction estimated at 14.5 psi. Find the power saving by intercooler and heat removed in the intercooler in Kilowatts.
A two stage compressor with first stage piston displacement of 94,390 cu.m/sec is driven by a motor. Motor output is 35 HP, suction temperature 22 degC, volumetric efficiency is 85%, mechanical efficiency is 95%, the intercooler pressure is 30 psi gage. Air temperature in and out of the intercooler are 105deg C and 44 degC, respectively. Final discharge pressure is 100 psi gage, while suctionis estimated to be 14.4 psi. Determine the compression efficiency.
A fan manufacturer rates his fans at 152 mm water gage static pressure for 10 m² of air per second at 21°C, 1,200 rpm and static efficiency of 69%. At what speed, in RPM, would these fans operate to develop 130 mm water gage when the temperature is 316°C?
From a test of an air compressor driven directly by a steam engine , the following data and results were obtained: capacity, 800 cfm; suction at 14.7 psia; discharge at 110 psia; indicated work of the compressor, 155 hp; indicated work of steam engine, 172 hp. Calculate (a) the compression efficiency and (b) the overall efficiency. Ans. (a) 90.06%; (b) 81.16% with step by step please! thanks
Energy balance results (in kW) obtained for the same medium speed single cylinder diesel engine are reported in the following table. For case 1, if the coolant temperature is 105 °C at the outlet of the engine and the volumetric flow rate is 0.22*10-3 m3/s, the temperature of the coolant at the inlet is (in °C): (The coolant is considered water with a density 999 kg/m3 and a specific heat 4.2 k/kg.K). Case N (rpm) bmep (bar) W. O ambient Q ahast shaft 2.2 4.2 19.1 60.3 9.90 3.52 1 500 7.1 24.5 23.8 500 6.1 3.6 5.2 400 3.50 4.9 4.1 1.4 Select one: O a. 142.1 O b. 112.7 O c. 97.31 O d. 87.2 O e. 370.31
Looking at just the bypass flow of a large turbofan, assume that Min = 0.8, Tin = 225 K, Mdot = 90 kg/s, PRF = 1.6 and hF = 0.90. Let P0 = 25 kPa. Determine: (a) Vexit, (b) Thrust from the bypass flow assuming that it is chocked (MEX = 1).
A reciprocating piston compressor has the following:-Piston diameter of 300mm,-Stroke of 450mm,-Intake pressure of 1 bar,-Intake temperature of air at 200C,-Clearance volume of 3%,-Rotational speed N = 250rev/min,-Discharge pressure = 40 bar,-Compression and Re-expansion are polytropic process with k = 1.25a) Find the compressor’s characteristics (V,P T at all points A,B, C, D).b) Calculate the work and power of the compressor.
A Kaplan turbine has the following specifications: H =25 ft., N=400 rpm; power = 650 hp. If the efficiency of the unit is 90%, estimate (a) the flow rate, (b) approxi-mate diameter of the runner, (c) turbine setting to avoid cavitation if the location is at sea level, and (d) turbine setting to avoid cavitation if the location of the unitis at an elevation of 5000 ft. The local temperature is 60°F.Ans: (a) Q=254 cfs; (c) Hs=5.8 ft.; (d) 0.12 ft.
Suppose that the pump of Fig. is run at 1100 r/minagainst a pressure rise of 210 bar. (a) Using the measureddisplacement, estimate the theoretical delivery in gal/min.From the chart, estimate (b) the actual delivery and (c) theoverall efficiency.
Pls. answer thank you! The indicated efficiency of a steam engine is 65%. The engine entrance is 2600 KJ/kg and exit is 2100 KJ/kg. if steam consumption is 3500 kg/hr and mechanical efficiency is 90%, what is the brake power of the engine in Kw?
Discuss Brayton and Rankine cycles