Q3/ For the system shown below, the following are applicable: pl= 5 bar Q=0.004 m3/s, pipe total length3D15 m and internal diameter-30 mm (Take SG-0.9 and kinematic viscosity (v-0.0001 m2/s)). Find p2 in units of bars. Motor P1 Pipe length = 3m %3D Pump 90' elbow Globe valve Q Breather 38 mm (ID) Pipe length 2m %3D P2 90 elbow Load force Pipe length = 4 m Pipe length= 6m Valve or fitting K factor Return bend 2.2 45° elbow 0.42 90° elbow 0.75 Globe valve 10

Q3/ For the system shown below, the following are applicable: pl= 5 bar Q=0.004 m3/s, pipe total length3D15 m and internal diameter-30 mm (Take SG-0.9 and kinematic viscosity (v-0.0001 m2/s)). Find p2 in units of bars. Motor P1 Pipe length = 3m %3D Pump 90' elbow Globe valve Q Breather 38 mm (ID) Pipe length 2m %3D P2 90 elbow Load force Pipe length = 4 m Pipe length= 6m Valve or fitting K factor Return bend 2.2 45° elbow 0.42 90° elbow 0.75 Globe valve 10

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7. a. If the blood viscosity is 2.7x10-3 Pa.s, length of the blood vessel is 0.35 m, tubular resistance of a blood vessel is 38.5 GPa-s/m3 , What is the radius of the blood vessel in mm?b. If the blood pressure at the outlet of the above vessel is 30 mm Hg and the flow rate through the vessel is 100 ml/min, find the inlet pressure in mm Hg. Density of mercury = 13,550 kg/m3, acceleration due to gravity = 9.61 m/s2
Using the data given in the schematic attached, find the difference of pressure PA and PB h1= 0.65m h2= 0.1m h3= 0.75m h4= 0.45m Density of fluid A is pA= 900kg/m3 Density of fluid B is pB= 1034kg/m3 Mercury density is pHg= 13600kg/m3 Oil density is poil= 700kg/m3 (In the given figure, the pipelines are parallel to each other and not necessarily at the same height.)
Find the air horsepower of an industrial fan that delivers 40m3/s of air through a 700mm x 1000mm duct if static pressure is 150mm of water gage and air density is 1.18kg/m3 Answer: 182.2
2. A fan discharges 265 cu.m/min of air through a duct of 92 cm in diameter against a static pressure of 0.022 m of water. The fluid density is 995 kg/cu.m., the air temperature is 29°C and the barometric pressure reading is 730 mm Hg. If the power input to the fan is measured 3.5 hp, what are the total and static fan efficiencies?
The cylinder bore diameter of a double-acting reciprocating pump is 160 mm and its stroke is 340 mm. The pump runs at 53 rpm and lifts water through a height of 29 m. The delivery pipe is 22 m long and 100 mm in diameter. Find (i) the theoretical discharge in liters/s,(ii) the theoretical power required to run the pump in kW, (iii) the percentage of slip, and (iv) the coefficient of discharge., if the actual discharge is 10 liters/s. Assume the weight density of water is 9810 N/m3
Aiming a 1.69 in diameter garden hose straight up, forms a “bubbler fountain” that you could easily drink from (but you shouldn’t because of bacteria, etc.). The water flows out the hose and down the sides. If the water has a density of 63.1 lbm/ft^3 and a viscosity of 0.0119 g/cm*s, what is the thickness of the water film (df) (in cm) if the flow rate of water is 6.42 in^3/s? For simplicity, assume the film is thin enough that you can use rectangular coordinates.
Find an expression for the velocity of water leaving the sprinkler. Find an expression for the gauge pressure at point A, a distance L1, upstream of the narrow pipes. Express the answer in terms of the flowrate, Q. The inner diameter of the first segment of the pipe is d1=10mm, the inner diameter of the second set of pipes is d2=1mm, with N=25. The flowrate through the sprinkler is Q=0.2 L/s. Flow in pipes typically becomes turbulent when the Reynolds number exceeds 2000. Comment on the accuracy of the assumption that the flow could be treated as laminar everywhere. May be assumed water has a density of 1000kg/m^3 and a viscosity of 1mPa s.
Please solve it correctly,Urgent. Question: The discharge pressure of a water pump is 9, 000 kPa. The temperature is 150 deg deg C and density is 917 kg/m3. What is the equivalent pump head in meters? A. 11.005 m B. 1,000.5 m C. 1,050.5m D. 1, 100.5 m
The cylinder bore diameter of a double-acting reciprocating pump is 170 mm and its stroke is 370 mm. The pump runs at 55 rpm and lifts water through a height of 26 m. The delivery pipe is 23.5 m long and 113 mm in diameter. Find (i) the theoretical discharge in liters/s,(ii) the theoretical power required to run the pump in kW, (iii) the percentage of slip, and (iv) the coefficient of discharge., if the actual discharge is 13 liters/s. Assume the weight density of water is 9810 N/m3 (i)Theoretical discharge in liter/s (ii) the theoretical power required to run the pump in kW (iii) the percentage of slip (iv) the coefficient of discharge.
The figure shown below is a series pipeline system used to draw a fluid from a lower source open tank to a higher destination open tank . The flow and geometric layout for the system are listed below: Fluid: water Volume flow rate: Q=0.015 m3/s Elevation difference: h=8.0m of two free surfaces Suction line: DN100 Sch. 40 Steel pipe Length: Ls=2.0 m Valve1: hinged disc type foot valve Entrance type: well-rounded Discharge line: DN80 Sch. 40 Steel pipe Length: Ld=100 m Valve2: full open gate valve Elbows: 90ο long radius elbow (2) Select all energy loss types between section 1 and 2_________ A. Minor loss for the two elbows B. Friction loss in suction line C. Minor loss for Valve 1 D. Entrance loss E. Exit loss F. Friction loss…
The figure shown below is a series pipeline system used to draw a fluid from a lower source open tank to a higher destination open tank . The flow and geometric layout for the system are listed below: Fluid: water Volume flow rate: Q=0.015 m3/s Elevation difference: h=8.0m of two free surfaces Suction line: DN100 Sch. 40 Steel pipe Length: Ls=2.0 m Valve1: hinged disc type foot valve Entrance type: well-rounded Discharge line: DN80 Sch. 40 Steel pipe Length: Ld=100 m Valve2: full open gate valve Elbows: 90ο long radius elbow (1) Select the simplified general energy equations for section 1 and 2_________ A. B. C. D.
A pipe inclined at 45° to the horizontal (Fig. 2) converges over a length l of 2 m from a diameterd1 of 200 mm to a diameter d2 of 100 mm at the upper end. Oil of relative density 0.9 flowsthrough the pipe at a mean velocity ?̅1 at the lower end of 2 m/s. Find the pressure differenceacross the 2 m length ignoring any loss of energy, and the difference in level that would beshown on a mercury manometer connected across this length. The relative density of mercury is 13.6 and the leads to the manometer arefilled with the oil.