Q3 In large steam power plants, the feedwater is frequently heated in closed feedwater heaters, which are basically heat exchangers, by steam extracted from the turbine at some stage. Steam enters the feedwater heater at 1.6 MPa and 250 °C and leaves as saturated Steam from turbine 2 MPa 225 oC Feedwater з Мра 25 oC liquid at the same pressure. Feedwater enters the heater at 4 MPa and 30 oC and leaves 10 °C below the exit temperature of the steam. Neglecting any heat losses from the outer surfaces of the heater, determine (a) the ratio of the mass flow rates of the extracted steam and the feedwater heater and (b) the reversible work for this process per unit mass of the feedwater. Assume the surroundings to be at 25 °C. sat. liquid

Q3 In large steam power plants, the feedwater is frequently heated in closed feedwater heaters, which are basically heat exchangers, by steam extracted from the turbine at some stage. Steam enters the feedwater heater at 1.6 MPa and 250 °C and leaves as saturated Steam from turbine 2 MPa 225 oC Feedwater з Мра 25 oC liquid at the same pressure. Feedwater enters the heater at 4 MPa and 30 oC and leaves 10 °C below the exit temperature of the steam. Neglecting any heat losses from the outer surfaces of the heater, determine (a) the ratio of the mass flow rates of the extracted steam and the feedwater heater and (b) the reversible work for this process per unit mass of the feedwater. Assume the surroundings to be at 25 °C. sat. liquid

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steam turbine operates adiabatically at a power level of 3,500 kW. Steam enters the turbine at 2,400 kPa and 500°C and exhausts from the turbine as saturated vapor at 20 kPa. What is the steam rate through the turbine, and what is the turbine efficiency?
A steam turbine receives steam at a rate of 90 MTPH at 2 MPa and 5000C and exhausts it at 0.10 MPa. Considering indicated turbine, generator and mechanical efficiencies of 95%, 93% and 90%, respectively, determine the combined thermal efficiency of the turbine. in %
Consider a steady-state steam turbine. Steam enters the turbine at a pressure of 12.5 MPa and atemperature of 700℃, and leaves the turbine at a pressure of 0.5MPa. If the isentropic efficiency ofthis turbine is 86%, determine its second law efficiency.
A steady-flow thermodynamic system receives 100 lb/min of fluid at 30 psia and 200 Fahrenheit and discharges it from a point 80 ft above the entrance section at 150 psia and 600 Fahrenheit. The fluid enters with velocity of 1200 fpm and leaves with a velocity of 200 fpm. During this process, there are supplied 25,000 Btu/hr of heat from an external source and the increase in enthalpy is 2 Btu/lb. Determine the work done in horsepower.
4. A steady flow thermodynamic system receives 100lb/min of fluid at 30psia and 200 °F and discharges it from a point 80 ft above the entrance section at 150 psia and 600°F. The fluid enters with the velocity of 7200 fpm and leaves with the velocity of 2400 fpm. During this process, there are supplied 25,000 BTU/hr of heat from an external source, and the increase in enthalpy is 2.0 BTU/lb. Determine the Work done in horsepower.
A steam turbine operates adiabatically at a power level of 3500 kW. Steam enters the turbine at 2400 kPa and 500°C and exhausts from the turbine as wet steam with a quality of 97% at 20 kPa. Determine the turbine's efficiency and estimated lost work.
A steady flow thermodynamic system receives 100 lb/min of a fluid at 30 psia and 200°F and discharges it from a point 80 ft above the entrance section at 150 psia and 600°F. The fluid enters with a velocity of 7200 fpm and leaves with a velocity of 2400 fpm. During this process, there are supplied 25,000 Btu/hr of heat from an external source, and the increase in enthalpy is 2.0 Btu/lb. Determine the work done.A. 5.48 HpB. 6.20 HpC. 7.15 HpD. 8.08 Hp
Refrigerant-134a is to be cooled by water in a condenser. The refrigerant enters thecondenser with a mass flow rate of 6 kg/min at 1 MPa and 80°C and leaves at 30°C. The coolingwater enters at 500 kPa and 20°C and leaves at 40°C. Neglecting any pressure drops, determinethe mass flow rate of the cooling water required. (Hint: take the entire heat exchanger as thesystem and write energy equation for this system. Answer: 15.84 kg/min)
Steam enters the condenser of a steam power plant at 20 kPa and aquality of 90 percent with a mass flow rate of 20,000 kg/h. It is to be cooled by water from anearby river by circulating the water through the tubes within the condenser. To preventthermal pollution, the river water is not allowed to experience a temperature rise above10°C. If the steam is to leave the condenser as saturated liquid at 20 kPa, determine(a) the mass flow rate of the cooling water required, and(b) rate of heat loss from the steam
Steam enters the condenser of a steam power plant at 20 kPa and aquality of 90 percent with a mass flow rate of 20,000 kg/h. It is to be cooled by water from anearby river by circulating the water through the tubes within the condenser. To preventthermal pollution, the river water is not allowed to experience a temperature rise above10°C. If the steam is to leave the condenser as saturated liquid at 20 kPa, Determine(a) the mass flow rate of the cooling water required, and(b) rate of heat loss from the steam. Please attempt (a) then (b)
Refrigerant-134a is to be cooled by water in a condenser. The refrigerant enters the condenser with a mass flow rate of 6 kg/min at 1 MPa and 70oC and leaves at 35oC. The cooling water enters at 300 kPa and 15C and leaves at 25oC. Neglecting any pressure drops, determine ; i. The mass flow rate of the cooling water required.ii. The heat transfer rate from the refrigerant to water.
4. Steam enters the condenser of a steam power plant at 20000 kPa and a quality of 95 percent with a mass flow rate of 20 Mg/h. It is to be cooled by water from a nearby river in circulating the water through the tubes within the condenser. To prevent thermal pollution, the river water is not allowed to experience a temperature rise above 10oC. If the steam is to leave the condenser as saturated liquid at 20000 Pa, determine the mass flow rate of the cooling water required