Q3. A pump is required to pump water from a large reservoir to the water tower located 20 m above the reservoir (Figure 1). If 0.03 m/s of water having a density of 1000 kg/m3 is pumped through a 30-mm pipe. a. How much power is required to be delivered to the water by the pump? Consider the flow losses in the pipe; do the necessary assumptions. b. Determine the efficiency of the pump

Q3. A pump is required to pump water from a large reservoir to the water tower located 20 m above the reservoir (Figure 1). If 0.03 m/s of water having a density of 1000 kg/m3 is pumped through a 30-mm pipe. a. How much power is required to be delivered to the water by the pump? Consider the flow losses in the pipe; do the necessary assumptions. b. Determine the efficiency of the pump

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows from Reservoir A (Elev 125 m.) to a turbine (Elev 67 m.) then discharges into tailtrace B (Elev 26 m.) as shown. The head loss from (A) to (1) is 2 times the velocity head in the pipe, and the head loss from (2) to (b) is 1.97 times the velocity head in the pipe. If the flow rate in the pipe is 39 ft3/s, diameter of all pipes is 30 in, calculate the horsepower generated by the turbine. Use 1 hp = 550 lb-ft/s. ANS : 1,000,000
Q2: Water is flow by arate = (v/( “7— /20) m¥/s , the water is still stable due to using a pump as shown in figure below. A pipe of rectangular cross sectional area of dimension (10 *20 ) cm is used to connect the two reservoir, friction factor for the pipes(£=0.02), if K value in the entrance and in the exit are 0.1 and 1 respectively. Calculate the pump power:- ElL15m Water EL10m Water = o cotanantwe *10 = 50 m——
A water pump at elevation 46 m. is used to bring up 250 gpm of water from a river (elev. 45 m.) to reservoir at elevation 100 m. If the suction pipe from the river to the pump is 8 inches in diameter with a head loss of 4 times its velocity head and the discharge pipe from the pump to the reservoir is 6 inches in diameter with a head loss of 25 times its velocity head, determine the output of the pump in horsepower. A. 10.6hp B. 11.6 hp C. 12.6 hp D. 9.6 hp A 3 mm diameter tube is connected in series to a 12 mm diameter tube. Water Flows at 0.5 m/s in the larger tube. Determine the velocity in the smaller tube. A. 6 m/s B. 10 m/s C. 8 m/s D. 12 m/s
A pump draws water from a 200mm diameter suction pipe and discharges through a 150mm pipe in which the discharge is 80 L/s. The pressure at point A is -40KPa. The 150mm pipe discharges into air at point B as shown. If the head loss from point A to point B is 5m, determine the power needed to be given by the pump in horsepower.
A pump draws water at 20 liters per second from reservoir A and lifts it to reservoir B, as shown in Figure . The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe, and the head loss from 2 to B is fifteen times the velocity head in the 100-mm diameter pipe. 1. Compute the Power delivered by the pump in kw ( A. 79.07 , B. 48.10 C. 13.08 , D. 57.23) 2. Compute the Pressure head at point 1 in m. ( A. 85.96 , B. 19.74 C. 245.09 , D. 45.90) 3. Pressure head at point 2 in m. ( A. 104.51 , B. 246.67 C. 57.84 , D. 12.69)
The head-discharge relationship for a certain pump can be represented by the equation H = 28 - 9Q2. The pump is fixed 2.5 m above the water surface in a river and it forces the water to a tank at a level 10 m above the pump. The suction and delivery pipes are 15 m and 740 m long, respectively and each pipe is 0.5 m in diameter. The pipe coefficient of friction (f)is 0.017. Estimate the discharge (in m3/s) at the best operating point for the pumping system. Q = 0.9 m3/s Q = 1.1 m3/s Q = 0.4 m3/s Q = 0.6 m3/s
A pump is used to raised water to a reservoir through 1000 m. long of 20 cm diameter with Cw of Hazen-William's Equation equal to 100. If the pipe is to be replaced with a new one having the same length but with a diameter of 25 cm and Cw= 120, determine the power save if the flow is to be maintained at 75liters per second. Draw the approximate EGL and HGL
2. Compute the rate of flow in a pipe with diameter300 mm for a length of 900 meter having a head loss of 6.119 meters, if f=0.02 (Hint: Use h=(0.0826fL(Q^2))/(D^5)
The water system in a suburban area consists of an old 200mm pipeline 760m long which conveys water from a pump to a reservoir whose water surface is 107m higher than the pump. Water is pumped at the rate of 0.07 m3/s. Determine the horsepower saved by replacing the old pipe with a new 250mm pipe. Assume the value of f as equal to 0.022 and 0.033, respectively, for the old and new pipes. Neglect losses of head except friction head show the diagram and complete solution. Need ASAP. Thank you
A cylindrical water tank has a height of 6 m and a radius of 4 m. How much work is required to empty the full tank by pumping the water of the outflow at the top of the tank (p=1000kg/m^3 and g=9.8m/s^2)
A cylindrical water tower of diameter 3.5 m supplies water to a house. The level of water in the water tower is 30 m above the point where the water enters the house through a pipe that has an inside diameter 5.1cm. The intake pipe delivers water at a maximum rate of 2.2 ×10−3 m3 ⋅s −1. The pipe is connected to a narrower pipe leading to the second floor that has an inside diameter 2.5 cm. What is the pressure and speed of the water in the narrower pipe at a point that is a height 5.5 m above the level where the pipe enters the house?
Water flows from Resorvoir A (Elev 133 m.) to a turbine (Elev 76 m.) then discharges into tailtrace B (Elev 30 m.) as shown. the head loss from (A) to (1) is 2 times the velocity head in the pipe, and the head loss from (2) to (b) is 1.49 times the velocity head in the pipe. if the flow rate in the pipe is 35 ft63/S, diameter of all pipes is 25 in., calculate the horsepower generated by the turbine. Use 1 hp = 550 lb-ft/s.