Q3. Find stresses in the Bronze and Aluminum. Find the force needed tojust close the gap.1000 KNAns.: opronze = 36.15 MOAluminum = 170 M AluminumA-0.0045mmF = 628.75 KNETO eBronzeA 0.0065mmE OpaL150mm 0.3mm

NOTE:- Here, Reder must do correctionvwhile taking area from above figure because it gives in mm^2…

Answered: Q3. Find stresses in the Bronze and…

Engineering

Mechanical Engineering

Q3. Find stresses in the Bronze and Aluminum. Find the force needed to just close the gap. 1000 KN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.15P: A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded...

See similar textbooks

Related questions

Q: A) Find the principal Stresses B) Find the Maximum Shear Stress 30 MAa $45 MPa 60 MPa

Q: A tank 10 m high and 2 m in diameter is 15 mm thick. The max tangential stress is ? The max…

A: To find: The maximum tangential stress and maximum longitudinal stress. Given: The height of the…

Q: Find the stresses at points A andB on the plate shown in the figure.

A: The normal stress at the points A and B can be determined as,

Q: Given a shear stress of txy 5000 psi and a shear modulus of G 1.15 x 107 %3| psi, find the shear…

A: Shear stress, τxy=5000 psiShear modulus, G=1.15*107

Q: below, find the maximum shear stress and maximum normal stress

A: to find Maximum shear stress and maximum bending stress.

Q: The state of stress at a point is given by ox=-6 MPa, oy=4 MPa, and Txy=-8 MPa. The maximum tensile…

A: To find: The maximum tensile stress at the point. Given: The stress are σx=-6 MPa, σy=4 MPa and…

Q: F V=FU M=hF Find the principal stress at point C and D

Q: Find the insitu stress

A: We will use the formula to find the resultant of two stresses on any oblique plane

Q: An cylinder is 30 cm in diameter and the steam pressure is 7 kg/cm. If the cylinder head is held by…

Q: Q2 Find the stress in steel bar

A: P = 10 KN Diameter = 14 mm = 0.014 m

Q: A lamina is subjected to normal stresses along x axis 50 N/mm 2 and y axis 75 N/mm 2. Find the…

Q: Ex: Find the stress in steel and aluminum if the bars are rigid.

Q: The state of stress at a point under plane stress condition is Ox = 150 MPa, Oy = 50 MPa, Txy = 20…

A: Mohr's circle is a two dimensional graphical representation of state of stress at a point. Mohr's…

Q: Two carbon steel balls, each 30 mm in diameter, are pressed together by a force F. In terms of the…

Q: Given a shear stress of Txy = 5000 psi and a shear modulus of G 1.15 x 107 psi, find the shear…

Q: Mechanics of Materials Two forces are applied to the 100 mm diameter plate attached to the 40 mm…

A: Given: The loads on the shaft is shown below:

Q: A tank 12 m high and 2 m in diameter is 15 mm thick. The max tangential stress is ? The max…

Q: a) Find the temperature change in the steel and aluminium rods when the lower end of the aluminium…

Q: 1. Find the flexural stress at point A 2.5 kN/m 2.25 m 3.5 m

Q: the normal stress oy (in kPa)

A: Given; σx=100 kpaζxy=50 kpa The state of stress at a point ,for a body in place stressis shown in…

Q: A lamina is subjected to normal stresses along x axis 50 N/mm 2 and y axis 75 N/mm 2 Find the normal…

Q: Q4. The stresses at a point in a component are 160 MPa and 60 MPa both tensile. Find the intensities…

Q: A cylindrical steel pressure vessel with a diameter of 1200 mm and a wall thickness of 20 mm is…

Q: Find the longitudinal stress in the tank.

A: To Find the longitudinal stress.

Q: Find the stresses in A, B and C?

Q: The compressor in the figure is made of steel plate with a wall thickness of 2 mm and is resistant…

Q: A state of stress at a point A is given by ox = 210 MPa, oy = -140 MPa, and txy = 95 MPa. Which of…

A: The correct answer is option e) 234.071 Mpa

Q: A beam is subjected to a force of 150KN and the area of cross-section of the beam is 75cm2. Find the…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: Find normal stress . Take d=1.1 mm

A: Given data : Tensile load=P Diameter of circular rod=d To find : Normal stress

Q: For the stress states listed below, find the largest principal normal Ox = 244 MPa, Oy = 76 MPa, Txy…

A: The step by step solution is given below, σx =244 MPa σy =76 MPa τxy= 249 MPa

Q: The state of stress at a point under plane stress — 40 MPа, Суу condition is Oxx 3D 100 MPа and Txy…

A: Given, Stress in x-direction = σx = 40 MPa Stress in y-direction = σy = 100 MPa Shear stress in x-y…

Q: The stresses on an element are o, = -300 psi and o „=-600 psi. Find the maximum shear stresses on…

Q: st internal pressure, find w allowable stresses for the y are reached simultaneo

Q: Calculate the normal stresses (in Pa) at point Bof the bracket caused by the 23010N force.

Q: ..For the figure shown blow, if the temperature decrease by 40°C. find the stress in the Aluminuim…

Q: střéss is proporti of shear stress is p r stress is proport

A: A Newtonian fluid is one in which the viscous stresses generated by its flow are linearly…

Q: Find the principal normal stresses and their directions that will occur in case of stress in the…

Q: C, D a. V=FU M=hF Find the principal stress at point C and D

A: Given: The bending moment at section a-a, M = hF The section modulus of the section a-a, Zs= Z

Q: a) Calculate the principal stresses, given that the state of plane stress for an element is: Oy =…

Q: Q3: A state of plane stress case where the normal stress is of ox , Oy and shown in fig . At a…

Q: Find the principal stress at point C and D

A: The force F causes the bending moment at point C, and at point D only shear force will be there…

Q: 5. A cylindrical pressure vessel has an inner diameter of 240mm and a wall thickness of 1.5mm. If…

Q: 2. A point in a strained material is subjected to a tensile stress of 50 MPa. Find the normal and…

Q: Question: Find schematically the normal and shear stresses in the plane when the element in the…

Q: principle planes are planes ich are separated by 30 where When the shear stress is not zero When the…

A: The principle planes are two planes which are separated by 90° where the principle stresses occur.…

Q: 4. The general stress element is loaded such that ox = 30 MPa, oy = -20 MPa, Txy = 5 MPa. Using…

Q: the maximum shear stress (in MPa) at the point is

A: Given; In a plane stress condition, Stress at a point are; σx=20 MPa σy=80 MPa σxy=40…

Q: Two perpendicular tensile stresses of 300 MPa and 150 MPa act at a point in a material. Draw the…

Q: Q2 A steel bar of cross-sectional area 200 mm2 is loaded as shown in Fig. Find the change in length…

Question

Q3. Find stresses in the Bronze and Aluminum. Find the force needed to
just close the gap.
1000 KN
Ans.: opronze = 36.15 M
OAluminum = 170 M Aluminum
A-0.0045mm
F = 628.75 KN
ETO e
Bronze
A 0.0065mm
E Opa
L150mm 0.3mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

From the graph find stress? and yong modulus,E?
A thin cylindrical pressure vessel of 1.2 m diameter generates steam at a pressure of 1.75 N/mm2. Find the minimum wall thickness, if (a) the longitudinal stress does not exceed 28 MPa; and (b) the circumferential stress does not exceed 42 MPa
How to find circumferencial stress in the cylindrical vessel. Give the equations.
answer this ; The von Mises equivalent stresses at point H can be calculated as MPa
An cylinder is 30 cm in diameter and the steam pressure is 7 kg/cm. If the cylinder head is held by 12 studs, find the size, assume safe tensile stress as 280 N/mm
For the two-dimensional stress fi eld shown in Fig. it isfound thatσxx = 3000 lbf/ft2 σyy = 2000 lbf/ft2σxy = 500 lbf/ft2Find the shear and normal stresses (in lbf/ft 2 ) acting onplane AA cutting through the element at a 30° angle asshown.
Find the stresses in each direction, also find the change in volume of the block of dimension 120 mm x 60 mm x 43 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 10 kN (tensile), 25 kN (tensile), 13 kN (compressive) respectively, Take E as 180 GPa, Poisson's ratio as 0.3. The stress along length direction (Unit in kN/m2)= _____________ The stress along width direction (Unit in kN/m2)= _____________ The compressive stress along depth direction (Unit in kN/m2)= _____________ The change in volume of the block is (unit in mm3) = ______________
A wood stave pipe, 120 cm in inside diameter, is to resist a maximum water pressure of 1,200 kPa. If the staves are bound by steel flatbands (10 cm by 2.50 cm), find the spacing of the bands if its allowable stress is 105 MPa
Find the m ax- shear stress for the bean below?
P = 80 kN σt = 150 MPa t = 8.0782 mm Can you help me solve for d2?
A wood-stave pipe is bound by steel rods which take the untire bursting stress. Find the proper spacing for 8-mm diameter steel rod for a 1.80-m diameter wood stave pipe if the working stress is 60 mpa for a head of water of 20m.
A wood stave pipe, 120 cm in inside diameter, is to resist a maximum water pressure of 1,200 kPa. If the staves are bound by steel flat bands (10 cm by 2.50 cm), find the spacing of the bands if its allowable stress is 105 MPa.\ Please explain the steps and formulas used.