A beam is subjected to a force of 150KN and the area of cross-section of the beam is 75cm2. Find the stress in the beam.

Q: The cross-sectional area shown is subjected to V = 600 kN and M =1000 kN-m. What is the transverse…

A:

Q: A) Find the principal Stresses B) Find the Maximum Shear Stress 30 MAa $45 MPa 60 MPa

A:

Q: Find stress Force=2 N Area of cross section=1 m2

A: Given data : The value of force applied F=2 N The value of cross sectional area A=1 m2   Required :…

Q: A circular pipe of internal diameter 30 mm and thickness 4 mm is subjected to a force 30 kN and the…

A:

Q: Find the stresses at points A andB on the plate shown in the figure.

A: The normal stress at the points A and B can be determined as,

Q: Given a shear stress of txy 5000 psi and a shear modulus of G 1.15 x 107 %3| psi, find the shear…

A: Shear stress, τxy=5000 psiShear modulus, G=1.15*107

Q: below, find the maximum shear stress and maximum normal stress

A: to find Maximum shear stress and maximum bending stress.

Q: Q2) Layers of Brass, Steel and Aluminum are bonded together and formed section shown below.…

A:

Q: Find maximum shear stress

A: Given data : Normal stress in X direction= σX Normal stress in Y direction= σY Shear stress along XY…

Q: Given a shear stress of Txy = 5000 psi and a shear modulus of G 1.15 x 107 psi, find the shear…

A:

Q: as given below 80 mm a) Normal and shear stresses occurring at point A Find and show it on the plane…

A: Given: The diameter of the shaft, d = 20 mm = 0.02 m

Q: 2- If (maximum shear stress) Tmax=800 KPa, calculate L. 24KN A is ido mm 24KN

A: Given data: Maximum sear stress τmax=800 kPa Need to determine the value of L.

Q: A conveyor beam has the cross-section shown in Fig. 4.24 and it is subjected to a bending moment in…

A:

Q: 4. Find the average normal stresses on members AB, BE, and EG, If the area of all members is 1200mm…

A: In a truss, the force in each member can be determined using method of joints of sections. Force…

Q: Find the internal Shear Force at point C when P = 242 N

A: The vertical reaction at point A can be determined by taking the moment about point B.

Q: A horizontal force of P=40 kN is applied to joint C. The pin at A has a diameter of 25 mm. If pin A…

A: The free-body diagram of the given system can be drawn as below, Here, Ax is the horizontal force…

Q: If o, = 20 ksi, o, = 10 ksi, and ty = 30 ksi, what is the absolute maximum shear stress for the…

A:

Q: A water tank, 6 m in diameter, is made from steel plates that are 13mm thick. Find the maximum…

A:

Q: 1. Find the flexural stress at point A 2.5 kN/m 2.25 m 3.5 m

A:

Q: Find the maximum shear stress if maximum principal stress is 30 MPa Minimum principal stress 20 Mpa

A:

Q: 30 kN.m/m B Q1) Use G = 83 GPa, Find the maximum shear stress H m- D-0.1m

A: To find: The maximum shear stress. Given: The torque is T=30 kN·mm. The diameter of shaft is D=0.1…

Q: Example Fig. 4.19. If permissible stress is 150N/mm2, find its moment of resistance. Compare it with…

A: Area of I section = 7040 mm2 moment of inertia of I section; I = (bd3/12) - (b1d13/12)…

Q: For the following Mohr's circle: can we find the normal stress in X, the normal stress in Y and the…

A:

Q: Draw Mohr circle for the given stress state Find o1, 02 and R (Tmax) Txy = 40 MPa o, = 50 MPa = 30…

A: Given data:- Stress in x-direction, σx=50MPaStress in y-direction, σy=-30MPanegative for compressive…

Q: In a plane stress condition, the components of stress at point are ox = 20 MPa, ơy = 80 MPa and txy…

A: Given, Stress in x-direction = σx = 20 MPa Stress in y-direction = σy = 80 MPa Sheat stress in…

Q: For the beam below find the normal stress at sections in point (B) and (C) D B 75 kN 35 kN 45 kN…

A:

Q: Find the force which produce stress 22 N/mm2 on cross sectional area 2 mm2

A:

Q: Calculate the shear stresses at point A in the adjacent T-beam.F(maks)= 200 kN

A: Draw the labeled diagram of the given section.

Q: 5) Bars CE and DE in the truss have a cross-sectional area A = 25 cm?. Find the normal stress in…

A: Truss is a group of two forces. Only at the joints are forces applied. The forces in truss members…

Q: The stresses on an element are o, = -300 psi and o „=-600 psi. Find the maximum shear stresses on…

A:

Q: Find the stresses at points A and B on the plate shown in the figure.

A: The normal stress on the point A can be determined as,

Q: * For the cantilever beam shown. find the value of compound stresses at :point E due to Normal…

A: Given:P=2 KNPt=4 KNT=6 KN.mL=10 md=100 mm

Q: Find the stresses in A, B and C? And Vem 6m 0.006 MN cm B -Ha 4m 1 6cm

A: ◆ Stress in A : 1 MPa ◆ Stress in B : 1.67 MPa ◆ Stress in C : 1 MPa

Q: When sheer force acting on beam at F=60kN, find the sheer stress that occurs on the n-n section and…

A: Given:

Q: Find the minimum principal stress if maximum shear stress is 10 MPa and maximum principal stress is…

A:

Q: etermine the maximum mean shear stress in a 30mm diameter spline. (see picture)

A: Given:

Q: Find the stress if 1002 lb force applied on 12 in2

A: Given data : Force=P Cross sectional area=A   To find : Stress

Q: A tractor weighing 80 kN was lifted by 3 cables as shown in the figure. Calculate the stress on the…

A: Given: W=Mg = 80 kN The given system will have four forces to be in equilibrium. The equilibrium…

Q: Find the maximum shear stress at a plane if the major and minor principal stresses at a point are 3…

A:

Q: 3. Given a shear stress of Txy = 5000 psi and a shear modulus of G = 1.15 x 107 psi, find the shear…

A: As per our guidelines, we are supposed to answer only first one question in case of multiple…

Q: Find the hoop stress acting on a cylinder with the following information:

A: To find Hoop stress Acting on cylinder

Q: Find the stress acting on the surface of a thin sphere of diameter 15 cm, thickness 0.25 cm and the…

A: From the given question, Diameter of the sphere = d = 15 cm Thickness of the sphere = t = 0.25 cm…

Q: For the cantilever beam shown. find the value of compound stresses at :point A due to Normal…

A: Given:P=2 KNPt=4 KNT=6 KN.mL=10 mD=100 mm

Q: 16000 Psi. (a) Find the inside diameter "d" if the outside diameter is equal to 12 inches. (b) Find…

A: The modulus of rigidity of the hollow steel shaft is, G=12×106 Psi The torque transmitted by the…

Q: 4. The general stress element is loaded such that ox = 30 MPa, oy = -20 MPa, Txy = 5 MPa. Using…

A:

Q: Two perpendicular tensile stresses of 300 MPa and 150 MPa act at a point in a material. Draw the…

A:

Q: The hollow circular pipe is subjected to two forces P=1800 and F=2500. Inner and outer radius of the…

A: Force P will apply normal stress and bending stress at fiber A of the hollow pipe where as force F…

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.