Answered: Q3/from the figure below, if the load…

Q3/from the figure below, if the load p=125N, the weight w=200N, the coefficient of friction u=0.4. Draw the free body diagram. Does it will slip or not and tip or not? Why?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.3.7P: -7 Repeat Problem 2.3-5, but n include the weight of the bar. See Table I-I in Appendix I for the...

See similar textbooks

Related questions

Q: 4 Podle C -831 * FBD J 60 * 180-02 T₂ А в 60 Σfy=0 => <fx=0 ५ Σfy=03 20 Now +80-0₂ Consider Node B.…

A: And, free-body diagrams of nodes A, B and C.

Q: The air in a room measuring 8 ft x 9 ft x 12 ft is at 80 degrees fareinheight and 14.7 psig. What is…

A: The dimension of room is .The temperature of room is .The pressure of room is

Q: A two bar truss is subject to external force in both the horizontal and vertical directions a.)…

Q: The displacement in x at node 2 is -0.536 mm. If the applied force is increased to -400N, what will…

A: The displacement of node 2 when is

Q: Glycerin (specific gravity = 1.26) is added to a tank of water in such a way not mix. The depth of…

Q: A pipe line of length 2000 m is used for power transmission. If 110 kW power is to be transmitted…

A: The length of the pipe = 2000 mpower transmitted to the pipe, P = 110 kW =110000 Wwater pressure in…

Q: SOLVE STEP BY STEP IN DIGITAL FORMAT .- A double-acting cylinder with an internal diameter of 2…

Q: Consider the same beam with a second 60-inch-long rod added at the right end. This rod also has a…

Q: How does temperature variation impact the performance of transmission cabling?

A: Temperature variation impact on cable performance:1. Signal distortion : Change in temperature…

Q: Discuss the role of international standards, such as ISO 26262 for automotive systems, in ensuring…

A: International standards play an important role in system reliability and safety measures. Hence,…

Q: ow consider the same beam when a 60-inch-long rod is added at mid-span. The rod’s cross section area…

Q: Determine the nodal force for a linearly varying pressure p, on the edge of the axisymmetric element…

A: The width of the triangular part is and height is,

Q: <Chapter 8 (Combined Loading) Problem 8.57 Consider P = 55 kN. Part A Determine the maximum normal…

A: The load acting, P = 55 kN

Q: Determine the support reactions: 3m 43.8 kN/m₂ 29.2 kN/m 222.5 KN

Q: A.31 & A.33 Determine the reactions for the beams shown in Figures PA.31 and PA.33 3 m 60 kN 2m…

Q: determine the maximum and normal stress at section mn m | n Centroidal axis 60 mm 4

A: v

Q: 15° 700 N F. X

Q: A 10 ton screw jack with a size of 2 4 - 3 acme thread. Assuming =0.125 due to average quality…

A: d (Mean diameter) = 2.75 inchesμ (Coefficient of friction) = 0.125For a single-threaded screw: l =…

Q: ting be used for precise manufact

A: Acoustic-assisted 3D printing is a fast-growing technology that focuses on acoustic forces to…

Q: Which is more efficient the Diesel Cycle or the Otto cycle

A: Otto cycle.1. The Otto cycle is the thermodynamic cycle used in spark-ignition gasoline engines.1.…

Q: Task 1: As a maintenance manager at a plant, you are required to update the existing maintenance…

A: Maintenance Interventions:Preventive Maintenance (PM):Definition: Scheduled maintenance activities…

Q: Q1/B/From figure 1, Determine the force in members EH, ED and GH of the truss, and state if the…

A: A plane truss given

Q: Calculate the shear force and bending moment in each beam at sections 1-1, 2-2 and 3-3.

Q: I had a question, in the beginning when you multiplied dv/dy * dy/dt can you break it down for me in…

A: a= g - cy2we convert this equation into velocity terms and then we apply boundary conditions for…

Q: A projectile is launched with an initial speed of vo= 200 m/s at an angle of 0 = 60 deg with respect…

A: Solution:Given

Q: start of Process 3-1) Please answer the following questions. a. For process 1-2 determine the value…

A: (D) To plot the processes on a P−V diagram, you can use the provided information and the calculated…

Q: What is Constant Flow Method? Discuss some applications whereby the Constant Flow Method is used in…

A: The constant flow method is a technique used to measure the rate of a chemical reaction. It involves…

Q: Determine the internal forces at point E.

Q: CONDITIONS: 1. Liquid at P = 20 Mpa and T= 190 C 2. Saturated liquid at T = 223.75 deg C 3. Steam…

A: It is asked to find the property values and mark them on the TS diagram

Q: A[50,15,0]m F[29,-19,21] KN Vector Projection Problem 1 Calculate the projection of the force vector…

A: According to the given dataF=(29,-19,21) kNA(50,15,0) mWe need to findThe projection of the force…

Q: Consider the velocity field given by: V=−Ky(x² + y²)−0.5 { + Kx(x² + y²)−0.5j, a. Determine the…

A: Consider the given velocity field.Compare it with standard form of velocity field . Thus, and…

Q: Determine the steady state time response x(t) of a viscously damped system subjected to harmonic…

A: The mass is .The damping coefficient is .The spring stiffness is .The base excitation is

Q: 2- Represent the figures below according to an isometric perspective defined by: - Main edge (AP) -…

A: It is asked to draw the isometric view

Q: lower the temperature of nitrogen. Assume that ses have constant specific heat values: gen 1.042…

Q: Determine the support reactions: T 4 m + 4 m 150 KN 6 m 25 kN/m -10 m-

Q: nciples, design considerations, and practical applications that engineers in the field of mechanical…

A: Sustainable energy is nothing but the utilization of an adequate amount of energy without extensive…

Q: Find the factor of safety using the distortion energy theory. The diameter of the shaft is 20 mm. F1…

A: The properties of cold steel AISI 1006 are,

Q: Describe the principles of 7D printing and its theoretical applications in materials science and…

A: 7D printing is a theoretical concept that takes 3D printing to the next level by adding four…

Q: Your company is drilling a deep oil well in Texas. Fluids pressure encountered in that well at 15000…

A: Depth of the oil well: Pressure encountered: (pounds per square inch gauge)Acceleration due to…

Q: I belongs to mechanical engineering field please give answer according it Could you elaborate on…

A: Stress and strain are fundamental concepts in materials engineering that describe how materials…

Q: 4. In figure below find the force F, required to stop the system from moving P2=0, V₁=10ft/s and the…

Q: What is the heat stored the fluid in a geothermal reservoir 15 km² and 350 m thick with a uniform…

A: The area of the reservoir:Thickness of the reservoir:Porosity

Q: Discuss the concept of 4D printing and its potential applications in fields like architecture and…

A: 4D printing is an emerging technology that builds upon the principles of 3D printing but adds an…

Q: Draw the Isometric views of these ones

A: Given:Find:Isometric view

Q: A spherical water tank with an inner radius of 11 meters has its lowest point 3 meters above the…

Q: For the bent wire form shown, determine the support reactions at point A. 100 lb 8 in 3 in 6 in

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: The system consisting of the bar OA, two identical pulleys, and a secti shown in the figure.…

A: The free-body diagram is as follows-

Q: Flow separation: Using sketch, briefly describe the phenomena of flow separation at an arterial…

A: Flow seperation occurs at an arterial bifurcation region.And we have to discuss about it.

Q: What is the magnitude of a Force vector whose rectangular components are: Fx-60 kN, Fy=130 kN and…

A: Given:Fx = 60 kNFy = 130 kNFz = 80 kNRequired:F ( magnitude of the force vector )

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Q3/from the figure below, if the load p=125N, the weight w=200N, the coefficient of friction
u=0.4. Draw the free body diagram. Does it will slip or not and tip or not? Why?
1 m
1 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data:

VIEW

Step 2: Solution

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A bungee jumper having a mass of 55 kg leaps from a bridge, braking her fall with a long elastic shock cord having axial rigidity EA = 2.3 kN (see figure). If the jumpoff point is 60 m above the water, and if it is desired to maintain a clearance of 10 m between the jumper and the water, what length L of cord should be used?
-11 A rubber cube R of a side L = 3 in. and cross- sectional area A = 9 in2 is compressed inside a steel cube S by a force F = 5 lb that applies uniformly distributed pressure to the rubber. Assume E 0.3ksi and,, = 0.45. (a) Calculate the lateral pressure between the rubber and steel (disregard friction between the rubber and the steel, and assume that the steel block is rigid when compared to the rubber). (b) Calculate the change in volume of the rubber.
A steel post (E=30×106) having thickness t = 1/8 in. and height L = 72 in. support a stop sign (see figure), where s = 12.5 in. The height of the post L is measured from the base to the centroid of the sign. The stop sign is subjected to wind pressure p = 20 lb/ft2 normal to its surface. Assume that the post is fixed at its base. What is the resultant load on the sign? (Sec Appendix E, Case 25, for properties of an octagon, n =8.) What is the maximum bending stress in the post? Repeat part (b) if the circular cut-outs arc eliminated over the height of the post.
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
The hoisting arrangement for lifting a large pipe is shown in the figure. The spreader is a steel tubular section with outer diameter 70 mm and inner diameter 57 mm. Its length is 2.6 m, and its modulus of elasticity is 200 GPa. Based upon a factor of safety of 2.25 with respect to Euler buckling of the spreader, what is the maximum weight of pipe that can be lifted? (Assume pinned conditions at the ends of the spreader.)
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
A block R of rubber is confined between plane parallel walls of a steel block S (see figure). A uniformly distributed pressure p0 is applied to the top of the rubber block by a force F (a) Derive a formula for the lateral pressure p between the rubber and the steel. (Disregard friction between the rubber and the steel, and assume that the steel block is rigid when comp are d to the rubber.) (b) Derive a formula for the dilatation e of the rubber. (C) Derive a formula for the strain-energy density u of the rubber.
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
Solve the preceding problem for a W 250 × 44.8 wide-flange shape with L = 3.5 m. q = 45 kN/m, h = 267 mm, b = 148 mm, rt = 13 mm, = 7.62 mm, d = 0.5 m, and a = 50 mm.
-7 Repeat Problem 2.3-5, but n include the weight of the bar. See Table I-I in Appendix I for the weight density of steel.