Q4: 05 ig of water at 7bar and 15 is centained in a ylim energy is supplied until the temperature of cylinder contents becomes 204°c, the pressure of the contents remains at 7bar. der 0-3m diameter by frictlon-Less piston Heat Determine: a the heat energy supplied b. the distance moved by the piston, c. the work energy, d. the change in internal energy.

Q4: 05 ig of water at 7bar and 15 is centained in a ylim energy is supplied until the temperature of cylinder contents becomes 204°c, the pressure of the contents remains at 7bar. der 0-3m diameter by frictlon-Less piston Heat Determine: a the heat energy supplied b. the distance moved by the piston, c. the work energy, d. the change in internal energy.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

wo springs with same spring constant are installed in a massless piston/cylinder with the outside air at 100 kPa. If the piston is at the bottom, both springs are relaxed and the second spring comes in contact with the piston at V = 2 m3. The cylinder contains ammonia initially at -2°C, x = 0.13, V = 1 m3, which is then heated until the pressure finally reaches 1200 kPa. At what pressure will the piston touch the second spring? Find the final temperature and the total work done by the ammonia.
An adiabatic piston-cylinder device equipped with aspring maintains the pressure inside at 300 kPa, when thevolume is 0, and in 3 000 kPa, when the volume is 5 m ^ 3. Thedevice connects to a steam supply lineat 1,500 kPa and 200 ° C, and at the beginning the volume of the cylinder is 0.Determine the final temperature (and quality, if applicable) whenthe valve is opened and water vapor is allowed to enter from thesupply to the cylinder, until the pressure inside is equal tothe one on the line. Also determine the total workperformed during this adiabatic filling process.
A steel casting weighing 2 kg has an initial temperature of 500oC; 40 kg of water initiallyat 25oC is contained in a perfectly insulated steel tank weighing 5 kg. The casting isimmersed in the water and the system is allowed to come to equilibrium. What is its finaltemperature? Ignore effects of expansion or contraction, and assume constant specific heatsof 4.18 kJ/kg.oC for water and 0.5 kJ/kg.oC for steel.
A 0.5-m3 tank contains saturated steam at 300 kPa. Heat is transferred until thepressure reaches 100 kPa. Determine a) the heat transferred, b) the finaltemperature, and c) the final steam quality.
Determine the heat added in the system and its final pressure.Nitrogen with a mass of 2.5 kg expands at a constant pressure. Theinitial pressure and temperature in the piston cylinder system is 170kPa and 27 oC, respectively. Because of the heat transfer, the systemreached a final temperature of 200 oC. Note R= 0.2968 kJ/kgK Determine:a. The heat requiredb. The workc. The change of enthalpyd. The change of internal energy
Ms Png works on a piston-cylinder system which contains 0.05 m3 of nitrogen gasinitially at 200 kPa. At this state, a linear spring that has a spring constant of 150kN/m is touching the piston, but no force is exerting on it. Heat is then transferredto the nitrogen gas, causing the piston to rise and to compress the spring until thevolume inside the cylinder increases to 0.25 m3.a) Determine the final pressure inside the cylinder.b) Sketch the system on a P – V diagram.c) Calculate the total work done of the system.d) Deduce the work done against the spring to compress it.Given cross-sectional area of the piston = 0.25 m2Force applied by linear spring, F = kxk = spring constantx = displacement of the piston/spring
1. Moist air enters a refrigeration coil at 89 F dry-bulb temperature and 65 F thermodynamic wet bulb temperature at a rate of 14oo cu ft per min. The surface temperature of the coil is 55 F . If 3.5 tons of refrigeration are available, find the dry bulb and wet bulb temperatures of the air leaving the coil. Assume sea level pressure.
. Show that the law of the adiabatic process is given byPV ˠ = constantWhere: (ˠ) is the ratio of specific heat capacities.
Box the final answer. Write legibly. Steam flows into a turbine at a rate of 3.5 kg/s and ¾ MW of heat are lost from the turbine. Ignoring elevation and kinetic energy effects, calculate the power output from the turbine in KW? Steam pressure entering the turbine is 62 Bar at 440ºC and leaves at 74 Kpa.
could you explain were you get the numbers for formula to calculate heat transfer?Draw the T-V diagram showing all stages?Whats the final stage condition, is a gas, liquid explain? Solve using energy balance equation.
ass of | gas is compressed wzthout Jriction from an ini- Patoa al state of 0.15 m’ and 0.105 MPa, the pres- e pm ess. Thereis a transfer of 37.6 kJ of heat from ch does the internal energy of the gas change?
A piston-cylinder assembly initially contains 100 kPa of pressure and 2 Liter of air at 25 ° C. Then the air is compressed to 620 kPa pressure and 160 ° C. The useful work done for compression is 1.22 kJ. Assuming that the ambient pressure and temperature are 100 kPave 25 ° C, respectively, a) Calculate the availability of air in the initial and final states, b) the minimum work required for the compression process, c) the second-law efficiency of the process change.