Q4) A black and white television picture may be viewed as consisting of approximately 3x10° elements each one of which may occupy one of 10 distinct brightness levels with equal probability. Assume the rate of transmission to be 30 picture frames per second, and the signal to noise power ratio is 30 dB. Using the channel capacity theorem, calculate the minimum bandwidth required to support the transmission of the resultant video signal.

Q4) A black and white television picture may be viewed as consisting of approximately 3x10° elements each one of which may occupy one of 10 distinct brightness levels with equal probability. Assume the rate of transmission to be 30 picture frames per second, and the signal to noise power ratio is 30 dB. Using the channel capacity theorem, calculate the minimum bandwidth required to support the transmission of the resultant video signal.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A system uses channel bandwidth as 4 MHz and it can support a raw data rate of say 15 Mbps, assuming 2 Mbps as overhead then net date rate will be as 13 Mpbs, then its spectrum efficiency in 5 G
Given the narrow (usable) audio bandwidth of a telephone transmission facility, anominal SNR of 56 dB (400,000), and a certain level of distortiona. What is the theoretical maximum channel capacity (kbps) of traditional telephonelines?b. What can we say about the actual maximum channel capacity?
Answer the following: (a) What is the maximum data rate for a 64-level system with an analog bandwidth of 400 MHz? (b) What is the maximum data rate if that same system is subject to noise, with an average power level of 600 and an average noise level of 200? Include units in your final answer.
Calculate channel capacity, in bits per second, of a 10-MHz channel with an S/N ratio of 50 dB *
A communication system has a bandwidth of 150 MHz and an SNR (dB) of 35 dB. a. What is the theoretical maximum data rate (C) on this channel?b. How many signal levels (symbols) do we need to achieve this data rate?c. If we want to increase the maximum data rate to 10 Gbps, what SNR (dB) do we need on this medium?
Consider a telephone line initially noiseless channel having bandwidth and signal level determined by the network engineer. Calculate maximum data rate. After certain distance the channel becomes extremely noisy, so that the noise is strong which faints the signal .Calculate the capacity of the channel.
4.27 Consider a baseband M-ary system using M discrete a mplitude levels. The receiver mofiﬂl is as shown in Figure P4.27, the operation of which is governed by the following assumptions: Problems 305 (a) The signal component in the received wave is x £ m(t) = ; a, smc(T n) where 1/T is the signaling rate in bauds. (b) The amplitude levels are a, = *A/2, +34/2, ..., =(M — 1)A/2 if M is even, and 4, =0, *4,...,=(M— 1)A/2if Mis odd, * (c) The M levels ate equiprobable, and the symbols tranismitted in adjacent time slots are statistically independent. (d) The channel noise w(t) is white and Gaussian with zero mean and power spectral density No/2. () The low-pass filter is ideal with bandwidth B = 1/2T. (f) The threshold levels used in the decision device are 0, A4, ..., (M — 2)A/2 if M is even, and *4/2, *3A/2, ..., (M — 2)A/2 if M is odd. The average probability of symbol error in this system is defined by where o is the standard deviation of the noise at the input of the decision…
i) A communication system employs a continuous source. The channel noise is white and Gaussian. The bandwidth of the source output is 10 MHz and signal to noise power ratio at the receiver is 100. (a) Determine the channel capacity. (b) If the signal to noise ratio drops to 10, how much bandwidth is needed to achieve the same channel capacity as in (a). (c) If the bandwidth is decreased to 1 MHz, what S/N ratio is required to maintain the same channel capacity as in (a).
Derive the closed loop transfer function for the system in the image
Q3 (i) What do you mean by baseband transmission of a digital signal ? What are the possible types of connection of devices in a topology for communication?
Networking A digital signal is to be designed to permit 100 Mbps for a bandwidth of 10 MHz. Determine: (1) Number of levels (2) signal to noise ratio. (a) According to Nyquist Formula
a) Complete the incomplete root locus below.b) For which value range of K is the system stable?