All parts 10:04 AM Fri Jul 29Ta) Calculate the 4-point DFT of x[n]Q4frequency N = 4-point FFT algorithm.ECE 317 Digital Signal Processing I{x[0] == 1, 1, 1, 1} using the decimation-in-b) What is the computational cost of N=512-point FFT algorithm?Summer 202139%+:(w\->3+

Since you have posted the multiple questions so we are supposed to answer the 1st one.

Answered: Q4 a) Calculate the 4-point DFT of x…

Q4 a) Calculate the 4-point DFT of x [n] = {x[0] = 1, 1, 1, 1} using the decimation-in- frequency N = 4-point FFT algorithm.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

textbook: Magnetic resonance imaging, physical principles and sequence design. Problem 3.4 eq 3.33 : μx′(t) = μx′(0)μy′(t) = μy′(0) cos φ1(t) + μz′(0) sin φ1(t)μz′(t) = −μy′(0) sin φ1(t) + μz′(0) cos φ1(t) eq 2.24: d~μ/dt= γ~μ × ~B
An analog telephone line has an SNR of 45 dB and passes audio frequencies over the range of 300 to 3,200 Hz. A modem is to be designed to transmit and receive data simultaneously (i.e., full duplex) over this line without errors. If the frequency range 300 to 1,200 Hz is used for the transmitted signal while the frequency range 1,500 to 3,200 Hz is used for the signal being simultaneously received, computethemaximum capacity of the channel duringtransmission and reception?
Answer the following: (a) What is the maximum data rate for a 64-level system with an analog bandwidth of 400 MHz? (b) What is the maximum data rate if that same system is subject to noise, with an average power level of 600 and an average noise level of 200? Include units in your final answer.
A) The effective aperture of a 144.0cm-diameter parabolic reflector antenna is 6m of the physical aperture area. Compute the gain in dB at 10GHz. b) Vodafone decides to use a digital TDMA scheme that can tolerate a Signal-to-Interference Ratio of 17dB in the worst case. Find the optimal value of the path lost exponent for an omnidirectional antenna; assuming i=3 and j=2. Assume that there are six co-channel cells in the first tier, and all of them are at same distance from the mobile. Use suitable approximations. c) Draw the table of frequency assignments and system layouts for a seven-cell repeat pattern and three-sectored antenna per cell site, using E-GSM 900MHz in which the total number of channels needs to be divided, assuming that the full spectrum is available from the operator of the system is used. In the sixth (6th) cluster, list all the possible channels that will be assigned to the cells in sector B?
Fig. 1.35 shows the block diagram of a certain DSP system, given the fs is the sampling frequency used and X(t) = cos (2000πt) + 2cos (4000πt) + 3cos (10000 πt) In fig. 1.35, if fc = fs = 8kHz, sketch the spectrum signal y(t) for 0 ≤ f ≤ 8kHz. Briefly point out the possible problems or limitations for processing x(t), if any.
Consider a stable LTI system with input x(n) and output y(n). The zero-pole pattern of y(n)consists of a double zero at the origin of the z-plane and the poles 3 ± 3j. The zero-pole pattern ofx(n) consists of a double zero at the origin of the z-plane. Find the system function and the systemimpulse response.
Suppose two hosts, A and B, are separated by 20,000 kilometers and are connected by a direct link of R=2R=2 Mbps. Suppose the propagation speed over the link is 2.5⋅1082.5⋅108 meters/sec. Calculate the bandwidth-delay product, R⋅dpropR⋅dprop. Consider sending a file of 800,000 bits from Host A to Host B. Suppose the file is sent continuously as one large message. What is the maximum number of bits that will be in the link at any given time? Provide an interpretation of the bandwidth-delay product. What is the width (in meters) of a bit in the link? Is it longer than a football field? Derive a general expression for the width of a bit in terms of the propagation speed s, the transmission rate R, and the length of the link m.
A. A communication receiver works properly if the minimum signal-to-noise ratio is 15 dB. What should be the minimum signal power in Watts if the received noise power is 0.01 W? (Limit answer to 3 decimal places.) ================== B. Which of the following statements is/are true: Select one or more: a. Channel coding reduces the number of bits required to transmit a signal. b. The proper choice of a source coding algorithm depends upon the properties of what is to be encoded. c. Source coding is also known as compression. d. Lossy compression reduces the effects of bit errors.
PARTICULAR CONCEPT 1. Random Processes. 1.1. Temporal characteristics1.1.1. Concept of the random process.1.1.2. Stationarity and independence.1.1.3. Correlation functions. 1.2. Spectral characteristics.1.2.1. Power density spectrum.1.2.2. Definitions of noise. 1.3. Linear systems with random inputs. 1.3.1.1.3.1. Responses of linear systems to random signals. 1.3.2.1.3.2. Spectral characteristics of the system response. 1.3.3.1.3.3. Process sampling.
Assume that two hosts are directly connected via a submarine optical fiber cable, which goes from Los Angeles, CA to Shanghai, China. The cable length is 14,000 km. The bandwidth of the cable is R = 100 Gbps. Assume that the signal propagation speed in the cable is 2.0*10^8 m/s. Answer the following questions. (Make sure to have the correct number and unit for your answers whenever applicable.) a. What is the one-way propagation delay, dprop, between the two nodes? b. What is the Round Trip Time (RTT) between the two hosts? c. Calculate the bandwidth-delay product, i.e., R * dprop. d. What’s the meaning of R * dprop?
Which row represent the most stable system and why? nyquist and root locus plot attached.
Networking A digital signal is to be designed to permit 100 Mbps for a bandwidth of 10 MHz. Determine: (1) Number of levels (2) signal to noise ratio. (a) According to Nyquist Formula