Q4/ A wall (3m*2m) consist of 10 cm face brick with 15 cm concrete plaster. The outdoor temperature is -7°C, while the indoor space temperature is 24°C DBT and 10°C dew point temperature, Find i)heat transfer(Q) through the wall ii) Will moisture condense on this wall? аnd 1.3 ст сетеnt

Q4/ A wall (3m*2m) consist of 10 cm face brick with 15 cm concrete plaster. The outdoor temperature is -7°C, while the indoor space temperature is 24°C DBT and 10°C dew point temperature, Find i)heat transfer(Q) through the wall ii) Will moisture condense on this wall? аnd 1.3 ст сетеnt

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.29P: A mild-steel cylindrical billet 25 cm in diameter is to be raised to a minimum temperature of 760C...

See similar textbooks

Related questions

Q: Incident radiation at the Laguna Lake is 985 W/m2 at noon on February 14th. Water temperature is…

A: Write the formula for open water evaporation rate using the energy method. E=Rnlvρw Here, ρw is the…

Q: 2g of air in a piston cylinder is compressed isothermally. The initial temperature is 399 K the…

A: mass = 2 g = 0.002 kg initial temperature 399 K Initial pressure 7.1 bar = 710 kpa Final volume =…

Q: Q3: For system shown in Figure, Determine final temperature if R= 0.297 kPa-m' and ep = 1.04 kJkg-K.…

A: Given: Given: The gas constant, R = 0.297 kJ/kg.K The specific heat capacity, Cp = 1.04 kJ/kg.K The…

Q: 2.52 kg of coal per second are consumed by a steam boiler plant and produced 18.54 kg of dry flue…

A: Given Coal consumption = 2.52 kg/s Dry gas = 18.54 kg Ambient temperature = 32o C Average…

Q: 2.52 kg of coal per second are consumed by a steam boiler plant and produced 18.54 kg of dry flue…

Q: A piston-Cx at 400 Ĉ and 300 kpa Compressing the piston in Such that th, produa(p.v) der device…

Q: The heat transfer through a wall 25’x10’ is 8750 Btu/ hr. The outdoor air and surface temperature =…

A: Given Data→ Dimensions of wall 25'×10' Heat Transfer through a wall Q=8750 Btuhr Outdoor air and…

Q: How much air is used per kg of coal boiler having a chimney of 35 m height to create draft of 20 mm…

A: The answer is in next step

Q: Q4/ Steam at T1=320°C flows in a cast iron pipe (k=80W/m. C) whose inner and outer diameters are…

A: As per Bartleby's policy in case of multiple questions I can solve only first one. Please repost…

Q: Q4 : (Section A) A vessel has a volume of 0.1 m3 is fitted with a plunger enclosing 0.5 kg of steam…

Q: 5. A 500 m dark-colored swimming pool is located in a well-sheltered site where the measured wind…

Q: Q1: Find the following: A) The heat transfer per unit area through the composite wall in Figure…

A: As given above that T1=370°C and T2=66°C , AC=0.1 m2 ;LA= 2.5 cm, LB=LD=7.5 cm , LC=5 cm ; So the…

Q: 1. A scuba tank contains 1.5 kg of air. The air in the tank is initially at 15 °C. The tank is left…

A: Write the mass of air. m=1.5 kg Write the initial temperature of air. Ti=15 °C=15+273=288 K…

Q: A rigid vessel contains fluid at 1 MPa and 260 degree with a volume of 0.14 m³ is cooled until the…

Q: In Fig the 20 ° C water and gasoline surfaces are opento the atmosphere and at the same elevation.…

A: →Given data , specific gravity of liquid S=1.60 At 20° temperature , the…

Q: Refrigerant 134a flows in a 5-m long square duct that is located in a warehouse. One side of the…

Q: 4. 4-62 462Ikg of osypen is beated from 20 to 120°C Determine the amount of heat transfer required…

A: Data given- T1 = 20°C = 293 K T2 = 120°C = 393 K m = 1 kg

Q: Before the widespread use of mechanical refrigeration, cooling was provided by ice, which was…

Q: The quadrilateral rod without half (material: pure iron), seen in the figure, is immersed in water…

Q: 2. In an electric tea kettle filled with water, the bottom surface temperature is at 130 °C and has…

A: Given:Ts=130°Cd=5 in =0.127 mStandard atmospheric conditios:Temperature of water, Tw=20°CCp=4.186…

Q: An electric current is passed through a wire 1 mm in diameter and 10 cm long. The wire is submerged…

Q: Consider a house that has a floor space of 15m x 12m and an average height of 2.7 m at 150m…

Q: Consider an electrically heated room with a floor space of 100 m² and an average height of 4 m at…

Q: A carbon steel pipe (thermal conductivity of 38 W/m oC) with an external diameter of 5 cm and a wall…

A: Given : Kpipe= 38 W/mC D = 5 cm t= 4 mm t = 28 C T = 120 C To find : Heat lose per meter Insulation…

Q: A cylindrical vessel (D=98,4 cm) is filled with water (ρ=1000 kg/m3, c=4.187 kJ/kg.K) to a depth of…

A: Given data: - The diameter of the cylindrical vessel is D = 98.4 cm. The specific heat of water is…

Q: Q6 a) A 10-cm dia. copper ball is to be heated from 100 *C to till average temperature of 150 °C in…

A: Part A) Now find the total heat transfer as follows.

Q: C Hot air enters a sheet metal duct located in a basement. Determine the exit temperature and the…

Q: Q1. Derive Laplace equation for heat transfer by conduction in three dimension a2T 02T a2T 4 1 ат…

Q: Water is being heated in a closed vessel on top of a range while being stirred by a paddle wheel.…

Q: Q1: Find the following: A) The heat transfer per unit area through the composite wall in Figure…

A: Given Data: Temperature T1=370°C Temperature T2=66°C L1=0.025 m L2=0.075 m L3=0.05 m Cross sectional…

Q: A steam power plant is located in the northern part of the country. Steam in the plant flows…

Q: A cool box made of a material, having Thermal Conductivity of 0.22 W/m.°C has a total area of 3.9 m²…

A: Given Data Thermal conductivity of material is :k=0.22 W/m°C Total area is :A=3.9 m2 Initial…

Q: A single-phase fluid reservoir is described by four equal blocks as. The reservoir is horizontal and…

Q: A 10 cm thick and 1 m wide long steel plate is immersed in an oil bath at T0 = 40 ° C when the…

Q: In a reservoir system with a very large accumulation volume for the ideal fluid (water), a) Since…

Q: One kg of steam expands in a closed system according to a law PV1. =C from 700kPa to 70 kPa.…

A: m=1 kg Follow law PV1.1=CP1=700 kpaP2=70 kpainitially x=.9 Now we need to calculate the enthalpy at…

Q: When you go out to your car one cold winter morning you discover a 0.58-cm-thick layer of ice on the…

A: Given data A=1.6 m2L=0.58 cmT1=-2°cρ=917 kg/m3

Q: The essential component of a toaster is an electrical element (a resistor) that converts electrical…

A: Given: P = 12 W V = 110 V

Q: Consider a rectangu lar cauity ) hovzo ntal positi air とンン cokulate Hhe rate of heat traer in the…

Q: Q5/A 400 m light-colored swimming pool is located in a normal suburban site, where the measured wind…

Q: An electric current is passed through a wire 1 mm in diameter and 10 cm long. The wire is submerged…

A: Given problem belongs to subject HEAT TRANSFER and ENERGY BALANCE EQUATION is used to solve the…

Q: stem comprises a simple fluid for which C + PV/(n – 1) ere C and n are constant quantities and n =…

A: Option (a) is correct. 4kPa

Q: The heat loss through the roof of a building is 32.4 kW during the winter, when the temperature and…

A: Given: Heat loss Q=32.4kW RH=60% Dry bulb temperature=22°C Temperature outside the building T∞2=8°C…

Q: A rigid vessel contains fluid at 1 MPa and 260 degree with a volume of 0.14 m³ is cooled until the…

Q: Q 4. A transistor with a height of 0.4 cm and a diameter of 0.6 cm is mounted on a circuit board.…

A: Given data L=0.4 cmD=0.6 cmh=30 W/m2KTs=70°cTair=55°c

Question

100%

Q4/ А wall (Зт*2m) соnsist of 10 ст face brick with 15 ст сопсrete
plaster. The outdoor temperature is -7°C, while the indoor space temperature is 24°C DBT and
10°C dew point temperature, Find i)heat transfer(Q) through the wall
ii) Will moisture condense on this wall?
and I.3 ст сетеnt

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A mild-steel cylindrical billet 25 cm in diameter is to be raised to a minimum temperature of 760C by passing it through a 6-m long strip-type furnace. If the furnace gases are at 1538C and the overall heat transfer coefficient on the outside of the billet is 68W/m2K, determine the maximum speed at which a continuous billet entering at 204C can travel through the furnace.
A steam power plant is located in the northern part of the country. Steam in the plant flows steadily through a 0.203-m diameter pipeline from the steam generating unit (SGU) to the steam turbine. At the SGU end, the steam conditions are determined to be P= 4 mPa, t - 400 celsius, h =3,264.9kJ/kg, and specififc volume = 0.121 m3/kg. At the steam turbine end, the conditions are found to be P=3.5 mPa, t = 392 celsius, h = 3,133.9 kJ/kg, specific volume 0.261m3/kg. Heat loss from the pipeline is 6.92kJ/kg. Determine the steam mass flow rate in kg/s.
A pure copper cube 3 cm on each side is placed in a 15°C stream of water.If the initial temperature of the cube is initially at 215°C, how long does it take the cube to drop to 25°C? The convective heat transfer coefficient is 80W/m2∙K. Justify any assumptions.
A thick concrete wall having a uniform temperature of 50oC is suddenly subjected to a stream of water so that the surface temperature is suddenly lowered to 15oC. How long will it take to cool the concrete to 30oC at a depth of 5 cm from the surface? Data: concrete properties, k = 1.37 W/m×oC, r = 2100 kg/m3, a = 7.5×10-7 m2/s.
In a reservoir system with a very large accumulation volume for the ideal fluid (water),a) Since the diameter of the ABCDEF outlet pipe is D = 20 cm, the flow rate through the pipe,b) Calculate the velocity, velocity height, relative pressure and pressure heights in the ABCDEF outlet pipe.c) Draw the relative energy and piezometer lines of the system.d) If the relative evaporation pressure of water is pv = -98.5 kPa, what can be z maximum?e) Determine how much the diameter of the outlet pipe can be reduced at most without causing cavitation, with the relative evaporation pressure of water pv = -98.5 Pa and h = 6 m.f) Calculate the critical velocity value for cavitation.
An electric windshield defroster is used to remove 0.25-in of ice from a windshield. The properties of the ice are Tsat = 328F, uif = hif = 144 Btu/lbm, and v = 0.01602 ft3/lbm. Determine the electrical energy required per square foot of windshield surface area to melt this ice and remove it as liquid water at 328F. What is the minimum temperature at which the defroster may be operated? Assume that no heat is transferred from the defroster or ice to the surroundings.
Consider a tank with surface area A.(m2) It containsa fluid of M(kg) at an initial temperature of T0. (C) The specific heat of the fluid is Cp. (J/kg) The fluid inside the tank is heated with condensing vapour outside at temperature of Ts. find the equation that gives the change of the temperature of the fluid in the tank with time.T=f(t) neglect donduction heat transfer h=heat transfer film coef. homogenous T through the tank
A copper rod whose diameter is 2 cm and length 50 cm have one end in boiling water, the other end in a jacket cooled by flowing water which enters at 10oC. The thermal conductivity of the copper is 0.102 kCal/m-soC. If 0.20 kg of water flows through the jacket is 6 min, by how much does the temperature of the water increase?
Answer with a clean and neat solution In a piston cylinder system, the gas an initial pressure of 100 kPa and expands from 1.5 m3 to 7.5 m3 with an increase in internal energy amounting to [50 + (162/20)] kJ. Calculate the heat gain or loss in the system given the pressure volume relation as P2V is constant, where P is in kPa and V is in m3.
An electric current is passed through a wire 1 mm in diameter and 10 cm long. The wire is submerged in liquid water at atmospheric pressure, and the current is increased until the water boils. For this situation h = 5000 W/m2·C, and the water temperature will be 100◦C. How much electric power must be supplied to the wire to maintain the wire surface at 114◦C?
As part of an industrial pipe system a 6-meter-long by .5 meter inner diameter copper pipeweighing 200kg holds a lubricating oil in place while is heats from 20 deg C to 55 deg C. At thatpoint, the valve opens and allows to oil to flow through. What is the total heat transferrequired? And, what percentage of the heat transferred does the oil and copper each accountfor? (oil density = .9 kg/L , oil specific heat = 1800 J/kgC)
Q2.1 Explain the Fouling phenomenon. What is the effect of fouling on heat transfer rate?