Q4/ Answer the following: a) Give the color of 100Q resistor? b) Give the specification of the following? No. Name DC REGULATED POWER SUPPLY MA 1 00 2 5 3. 4)

Q: Apply tow sides of divergence theorem for the vector field E = 2p² (cos 50 a, – sin 5ø a, + az) for ...

A:

Q: The low-pass filter designed  has an input of 2cosωt V. 1. Suppose the power supplies are ±Vcc. What...

A: For active low pass filter  

Q: A 220V shunt motor develops a torque of 108 N.m at an armature current of 20 A. The torque developed...

A:

Q: What will be the free space path loss if the distance between the transmitter and the receiver is 15...

A:

Q: - Find v, using superposition: www- ww- 4 kΩ 2 kQ + 1 kN 10 V)3 kN$ Vo 6 A ww-

A:

Q: Type your quastion here

A: Acoording to the given data : p=6 Pload=12000 W V=240 V Eg1=250 V ϕ2=1.2ϕ1 Number of parallel paths ...

Q: High voltage high torque d-c motor oW voltago lo w toraue noto

A:

Q: The Wheatstone bridge shown in Figure 2.66 has vs=10 V,R1=10 kΩ,R2=10 kΩ, and Rx=5932 Ω. The detecto...

A:

Q: Which of the following represents the rotating losses of machine Friction and windage losses Eddy cu...

A: Due to the rotation of machine flux leakage occurs this cause to various losses 1. Friction and wind...

Q: Type your question here Q1// Answer the following question. 1- A 8-pole a separately excited generat...

A:

Q: A dc motor operates with a load that demands constant developed torque. With VT=200 V, the motor ope...

A: Given: To determine the speed of VT which is increased to 250 V. Vt= 200Ia= 10Ra= 5  

Q: For the amplifier as shown, VDD = 12 V, VSS = 12 V, ISS = 20 μA, and RD = 820 kΩ. Assume IDSS = 1 mA...

A: Calculating Drain current ID=ISS2ID=20 μA2ID=10 μA Calculating output voltage V0=-VDD+RDIDV0=-12 V+8...

Q: find the veltaage and (05) In the Circuit shaon in fig. the curreut in Bach ristence 92

A:

Q: Fing Vab in the given network

A:

Q: Identify the configuration in Figure 7.24 that is not a correct representation of I and H.(Answer ne...

A: According to right hand rule  if curl of fingers represent current direction then thumb will represe...

Q: walue of ſ D. dS is equal to

A:

Q: A single core cable has a conductor radius of (1cm), and insulation thickness of (0.4cm), if the spe...

A:

Q: This from probability and random variables course.

A:

Q: Plot a graph of the voltage transfer characteristicfor an ideal inverter with V+ = 2.5 V, V− = 0 V, ...

A: Using given details, to plot a graph for the voltage transfer characteristics for an ideal inverter ...

Q: Explain microwave oven is generating power or absorbing power.

A: A microwave is an electromagnetic wave races through the air at the speed of light. They are effecti...

Q: Find the power, reactive power, and apparent power delivered by the source in Figure P5.83. Find the...

A: Given: A circuit in which

Q: (D^2+4D+4)y=0; when x=0, y=1, y'=-1

A: (D²+4D+4)y=0;x=0,y=1,y’=-1; Solution: (D+2)² D=-2,-2; Characterstics Equation  is Real and Equal y=(...

Q: A single core cable has a conductor radius of (1cm), and insulation thickness of (0.4cm), if the spe...

A:

Q: A boost chopper is powered by a 12-V dc power supply. What is the output voltage range of this chopp...

A:

Q: Find      vo    and power dissipated in all the resistors using nodal analysis in the circuit

A: Therefore, Vo=3 volts

Q: An inverting amplifier is to be designed to have a closed-loop gain of 60 dB. The only op amp that is...

A: Given  Closed loop gain in dB AV=60 dB Open loop gain in dB A=106 dB FGE≤1 percent AVideal=-R2R1AV=A...

Q: Explain why the maximum value of the duty cycle must be limited in certain boost choppers. //(L-7)

A: We know that the boost chopper output (EO) is proportional to the DC voltage provided that the boost...

Q: The following figures give the O.C.C. of d.c. Shunt generator driven at a constant speed of 700r.p.m...

A:

Q: For P pole machine relation between electrical degrees and mechanical degrees is Oelec = 0mech %3D )...

A: For the P pole machine, the relation between electrical and mechanical degree is given as:

Q: solve 4 q pls

A:

Q: A balanced positive-sequence three-phase source hasvan(t)=100 cos(377t+90°) V a. Find the frequency ...

A:

Q: A rod of length L=0.65m is placed along the x-axis from x=0 to x=L. The rod carries a uniform linear...

A: The distribution is shown below:  A.  The expression for the infinitesimal charge along the rod in ...

Q: The voltage transfer function of either low-pass prototype filtershown  isH(s)=1s+1. Show that if ei...

A: (a) Draw the given circuit in the s-domain.

Q: Find the maximum power that can be delivered to a resistive load by the circuit shown in Figure P2.8...

A:

Q: Electrical Engineering Question

A:

Q: A buck chopper is powered by a 200-V dc power supply. What is the output voltage range of this chopp...

A: Input voltage of buck converter is given Vi=200 V Range of duty cycle is given 30% to 95 % Output vo...

HVDC

HVDC stands for high voltage direct current in the electric power transmission system. The high voltage direct current system uses direct current (DC) for the transmission of electrical power through transmission lines in contrast with the alternating current that is the AC system. The HVDC is used to transmit bulk power point-to-point through long distances transmission lines. Power is rapidly transferred because the efficiency of transmission lines is greatly increased over long distances due to HVDC lines.