Q4: By using assembly language instructions, write suitable statements to execute the following (Choose Three Only) 1. Clear the DX register with just one instruction. 2. Clear the odd numbers of AX register with just one instruction. 3. Divide 4482H by 16H and put the quotient in the BX register (Without using Division instruction). 4. Save the flags contents to BL register.

Q4: By using assembly language instructions, write suitable statements to execute the following (Choose Three Only) 1. Clear the DX register with just one instruction. 2. Clear the odd numbers of AX register with just one instruction. 3. Divide 4482H by 16H and put the quotient in the BX register (Without using Division instruction). 4. Save the flags contents to BL register.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Assume the following register contents: $t0 = 0x01234567, $t1 = 0x56781234. Set back to these values back after answering each question. For the register values shown above, what is the value of registers ($t0, $t1, $t2, $t3) after executing each instruction? sll $t2, $t0, 2 and $t3, $t2, $t1
For the same new ANDI instruction, how would the EXECUTE state be implemented? In the box on the answer sheet, write the one or more missing lines that would go where the blank line appears below. Hint: If needed, the names of various signals are AC (accumulator), IR (instruction register), mem_data (memory output data), PC (program counter), operand (fetched operand field), MW (memory write). when ex_andi => state <= fetch;
What are the values of ECX, EBP, and ESP registers after executing the following instruction? push ECX Before ECX: 0xBABE EBP: 0x0012FF24 ESP: 0x0012FF24 After ECX: EBP: ESP:
1)Write code to multiply the contents of $s0 register by 36 without using multiply instruction. (You canplace the result back in $s1). 2)Write code to divide the contents of $s0 register (which is a signed number) by 8, without using divideinstruction. (You can place the result back in $s1)
Write assembly code snippet to extract exponent from single precision float sitting in rax register? Write assembly code snippet to detect if number sitting in rdx is negative or not? Write assembly code snippet to detect if number sitting in ah is even or odd? Write assembly code snippet to mimic push instruction, assume number to push is in rdx register. Write assembly code snippet to mimic pop instruction, return the number in rcx.
Using the AddTwo program from Section 3.2 as a reference, write a program that calculates the following expression, using registers: A = (A+B) - (C+D). Assign integer values to the EAX, EBX, ECX, and EDX registers. Set memory values that require support for signed and unsigned values. Verify your work by calculating by hand the result.
1- Perform an arithmetic shift right by two bits of the following bit pattern: 1001 1011 Select one: a. 0010 0110 b. 1100 1101 c. 0011 0111 d. 1110 0110 2- Which instruction moves the least significant bits of a product into register eight? Select one: a. mvlo $8 lo b. addu $B SO lo C. mfio $8 d. move $8 lo 3- What are the names of the two registers that hold the result of a multiply operation? Select one a. S0 and $1 b. high and low RO and R1 d. hi and lo 4- If you have two integers, each represented in 32 bits, how many bits might be needed to hold the product? Select one: a: 16 b. 64 C. 128 d. 32
) State whether the following instructions are valid or invalid? Define the valid instructions. In case any instruction is invalid then state the reason of their invalidity. ADD BX, [1234H] AND 23H, AL CMP AL, SP JCXZ Telecom IMUL BL
1.) The LD.PC controls when to write an address to the PC. During a BR instruction, what Boolean logic is used to assert LD.PC and overwrite the PC? 2.) Not all instructions that change the value of a general-purpose register (GPR) update the values of the N, Z and P registers. For what explicit type of values written to a GPR are the condition codes not updated? 3.) List all the LC-3 instructions that change a GPR, but do not update the conditional codes, N, Z, and P. 4.) Where does the FSM get the values n, z, and p to compare to N, Z, and P in the Boolean expression N.n + Z.z + P.p?
. If R1 = 0xEF00DE12, R2 = 0x0456123F, R5 = 4, R6 = 28; Find the values of the destination registers for the following instruction? a) LSL R1, #8 b) ASR R1, R5 c) ROR R2, R6 d) LSR R2, #6 Substantiate your answers appropriately.
14--> ) According to the memory view given below. If RO = 0x20000004, after the LDMIA rO, (r7, r3, r9} instruction is executed, which of the following is the r3 and r0 register contents, respectively (data layout to.g endian)?
Please answer this question and provide the explanation Assume the values of %ecx is 0x00000005 and %edx is 0x00000003. What would be the value of %ecx and %edx after performing the following instruction? 0x5555555461a <+0>: leal (%ecx, %edx, 8), %edx %ecx = 0x00000005, %edx = 0x0000003A %ecx = 0x00000005, %edx = 0x00000018 %ecx = 0x00000005, %edx = 0x00000030 %ecx = 0x00000005, %edx = 0x00000003 %ecx = 0x00000005, %edx = 0x0000001D %ecx = 0x00000005, %edx = 0x00000040 %ecx = 0x00000055, %edx = 0x0000001D %ecx = 0x00000005, %edx = 0x0000002A %ecx = 0x00000005, %edx = 0x00000025 %ecx = 0x00000005, %edx = 0x00000035