Q4: Design a buck-boost converterto provide an output voltage 12V from a source that varies 'between 10V-16V.Given the load resistor is 10 ohm. assuming the frequency is 50 KHzand the output voltage ripple is 1.5% Specity:a. The duty ratio.b. The value of inductor.c. The value of capacitor.Note: Determine the values of inductor and capacitor with D1 only.

There are three types of DC/DC converter is used in power electronics. They are Buck converter: In…

Answered: Q4: Design a buck-boost converter to…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

design a battery charger for safe operation in a damp garage environment to use for charging your 12 VDC car battery. Design specifications include: (a) Input is a 110rms VAC. (VP=110x ) at 60 Hz from a three wire service that meets the National Electrical Code. (b) Output is a nominal 12 volts VDC at the cathode of the diode. (c) Specify a resistor, R, to limit the maximum battery charging current to 10 amperes into the 12 volt car battery assuming the battery is completely dead (0 volts) when you first connect the charger. (d) There is no ripple voltage design specification. Explain why this is unnecessary in this application. (e) The battery charger case is metal. (f) Assume a diode with VF = 0.7 V (g) The fuse in the primary circuit is to protect the power supply from a short-circuit at the battery terminals either from total battery failure or accidentally short circuiting the charging cable to ground…
BASIC ELECTRONIC Given Sketch the drain and transconductance curve for VGS = +2V, +1V, 0V -1V, -2V, -3V and -4V.
The circuit diagram of step-up type DC-DC converter is given below. It is assumed that the output capacitor is large enough and the output voltage is constant. (Consider that there is no circuit losses.) Select an inductance value for the CCM operating state of the circuit. With this inductance value, taking into account the minimum input voltage and minimum output current, calculate the value of C so that the output voltage has a fluctuation of 1%.
(a) Draw the equivalent circuit used for ac analysis of the circuit shown . (Use transistor symbols for this part.) Assume all capacitors have infinitevalue. (b) Redraw the ac equivalent circuit, replacing the transistor with its small-signal model. (c) Identify the function of each capacitor in thecircuit (bypass or coupling).
An inductor is energized as shown in the circuit in the figure. The resistance in the circuit its value is R = 25 Ω, applied voltage VCC = 100 V, t1 = 5 ms and T = 50 ms. Transistor and diode Assume ideal. Turning of inductor current to zero in each switching period wanted. In this case, with the largest inductor that can be chosen, how many W is the power consumed in the resistor will it?
Draw the circuit diagram of a DC to DC converter – (forwardconverter, step-down or buck converter). Describe its principle ofoperation. Draw the waveforms of: voltage across the diode, currentthrough the diode, current through the transistor and current throughthe inductor. Write the expression and diagram for transfer function.
The average value of the output voltage with PWM is Vo = 5 V. If the on state duration Ton is 5 µs and supply voltage Vin = 20 V, find the duty ratio d, switching period Ts and switching frequency fs of the system. Draw the waveforms for Vin and Vo voltages stating on and off durations.
Design a POWER SUPPLY with 5V output voltage. Use zener diode as a voltage regulator. Then solve for theoretical computations. Thanks!
Build an AC/DC dual power supply circuit that draws a 60Vp-p sinusoidal voltage, to provide a dc output voltage of +15 V. Full analysis of voltages and currents should be included. What modifications would you recommend to draw more current while maintaining same output voltage?
This part deals with DC-DC converters. A. Draw the circuit for boost dc-dc converter and explain its principle of operation. B. Derive the input-output relation for a boost dc-dc converter in the case of discontinuous current flow mode of operation. solve both part and fast
What is the effective voltage in the primary of an ideal Trafo with a turns NP / NS = 660/60; connected to a half-wave rectifier with RC load, whose filter capacitor is 1000μF with a load of 100Ω whose average voltage of output is 13.05V? Draw the wiring diagram correctly and care with the units!
For full RC charging the constant "n" in the product: "nRC" is "5". Now, which should be the constant "n" in "nRC" such that the voltage in the capacitor is 50% of the supply voltage?

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS