A Flyback converter has an input of 332 V from a DC source, operating at 40 kHz with duty cycle approximately 1/3. The rated output is 12 V at 5 A. The circuit operates with continuous inductor current at threshold 1.5 A, and the turn ratio must be an integer. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state : iv. Sketch the diode current and switch current.

A Flyback converter has an input of 332 V from a DC source, operating at 40 kHz with duty cycle approximately 1/3. The rated output is 12 V at 5 A. The circuit operates with continuous inductor current at threshold 1.5 A, and the turn ratio must be an integer. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state : iv. Sketch the diode current and switch current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design of Bidirectional DC-DC Boost Converter. explain its working principle and plot its input - output graphs.
Draw the circuit diagram of a DC to DC converter – (forwardconverter, step-down or buck converter). Describe its principle ofoperation. Draw the waveforms of: voltage across the diode, currentthrough the diode, current through the transistor and current throughthe inductor. Write the expression and diagram for transfer function.
A Buck-Boost regulator an input voltage of V.= 24 V and supplies a load of 36 Ohm. The duty cycle K=0.75 and the switching frequency is 10 KHz. If it is required that the AVc = 100 mV and Al = 0.25 A, find the output voltage and the values of the required inductor and capacitor.
Assume ?? ≈ 0. Solve this problem using both the exponentialmodel and the constant-voltage model. For the constant-voltage model, use ???,?? = 0.7?
1.Design a buck converter and a resistive load operating in CCM mode with the following specifications:(∆V0)/V0= 0.5 %, Vin = 20 V, f =30 kHz, Duty cycle d=0.4, and R =5.33 Ω. Determine (a) the output voltage and current of the buck converter, the Critical(minimum) inductance for CCM mode (b) select L = 600 µH, find the maximum IL,max and the minimum IL,min inductorcurrents. find the capacitor value that corresponds to (∆V0)/V0= 0.5 % for this buck converter
design a battery charger for safe operation in a damp garage environment to use for charging your 12 VDC car battery. Design specifications include: (a) Input is a 110rms VAC. (VP=110x ) at 60 Hz from a three wire service that meets the National Electrical Code. (b) Output is a nominal 12 volts VDC at the cathode of the diode. (c) Specify a resistor, R, to limit the maximum battery charging current to 10 amperes into the 12 volt car battery assuming the battery is completely dead (0 volts) when you first connect the charger. (d) There is no ripple voltage design specification. Explain why this is unnecessary in this application. (e) The battery charger case is metal. (f) Assume a diode with VF = 0.7 V (g) The fuse in the primary circuit is to protect the power supply from a short-circuit at the battery terminals either from total battery failure or accidentally short circuiting the charging cable to ground…
Suppose a power supply is energized by an AC source of 119 V RMS. The transformer step-down ratio is 8:1, it uses a full-wave bridge rectifier circuit with silicon diodes, and the filter is nothing but a single electrolytic capacitor. Calculate the unloaded DC output voltage for this supply (assume 0.7 volts drop across each diode). Also, write an equation solving for DC output voltage (Vout), given all these parameters.
Please written by computer Answer the following questions:a. Name a suitable topology that can be used in the above DC/DC converters to achieve the required regulation with the minimum provided efficiency.b. Calculate the efficiency of the linear regulator.c. Calculate the total input power and the input current.d. Calculate the overall efficiency of the system.e. If a 100uF capacitor is used at the input to minimize the ripple. Assume the rise time of the input source is 0.2ms. Estimate the maximum inrush current to charge the capacitor to 12V.
Draw the AC equivalent circuit and find Zi, Zo, Av, Ai (ignore the effect of To). Show all the necessary derivations and label all the parameters properly.
The input voltage of a Boost converter is 10V, the duty cycle of the boost converter is 0.25. If a 10- ohm resistor load is connected to the output; what are the average current flowing in the MOSFET and the diode? what is the max voltage stress on the MOSFET and the diode?
The average value of the output voltage with PWM is Vo = 5 V. If the on state duration Ton is 5 µs and supply voltage Vin = 20 V, find the duty ratio d, switching period Ts and switching frequency fs of the system. Draw the waveforms for Vin and Vo voltages stating on and off durations.
Find the theoretical values and answer the questions. please answear about all this questions.