Q4) For the Schmitt trigger circuit of the following figure ,R1=50 KQ „R2 = 1002, Vref =0v, Vinp-p=1vsinewave, and Vcc=14,Vcc=-14.1) Determine threshold voltages VUTH, VLTH, frequency.2) Draw and explain the operation of an inverting Schmitt trigger3) What is hysteresis?4) Draw the input and output waveforms of an inverting Schmitt trigger circuit for a sinusoidal inputVinVcc6-VECR,

The figure given is inverting Schmitt trigger Upper threshold VUT=R2R1+R2 +Vsat.…

Answered: Q4) For the Schmitt trigger circuit of…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.2P

See similar textbooks

Similar questions

Describe this woofer it is Truvox 1225?
Using a labelled diagram, describe cold-junction compensation for athermocouple and explain why it is necessary. Describe cold-junctioncompensation using a temperature reference unit. Outline practicablemethods for compensation on industrial plant including electronic andsoftware compensation. State the advantages and disadvantages of thevarious techniques.
3) Explain the construction, principle of operation, circuit and applications of Variable reluctance transducer with neat diagrams. 4) Describe the construction of LVDT and explain its principle of operation with the aid of diagram, list the advantages, disadvantages and applications of LVDT.
1. (a) Define analog to digital converter (ADC). Draw a 4-bit ADC circuit using Op-Amps. (b) why modulations are used in AC telemetry.Draw and discuss a basic AC data telemetry system. Please ans both parts.
Figure Q3(b) shows a phase shift oscillator circuit. Given the feedback gain:i Determine an equation for frequency of oscillationii Calculate the value of capacitors, C, if the output voltage is equal to5 sin 3?? ?? and resistor, R is equal to 100 ??Ω.iii Calculate the open-loop gain, A, in order to generate an oscillating signal.iv Determine the value for ??1and ??2 in order to generate an oscillatingsignal. You may refer to the Appendix in page 5 and 6 for the commercialvalue of resistor.
For the 2 circuits shown above, βnpn = 100, βpnp = 50, VDO = 0.7 V, R2 = 150 kΩ, and RB = 12 kΩ Using the ac small-scale signal analysis, determine for each circuit: a) The voltage gain (Av = vout/vin) b) The input resistance (Rin) c) The output resistance (Rout)
What is the input impedance of Common Emitter Collector Feedback preamplifier whose Collector Resistor is 2.7kohms, Feedback Resistor 180kohms,Beta=200, Vcc=9V?
a) what should be the operating frequency to have a high frequency gain of 30 % lower that the mid band gain. Assume a DC gain of 100 dB & Dc cut – off frequency @ 15 KHz.?
Q9. Draw Zener regulator circuit to obtain regulated DC voltage 6.8 V. Considering input DC voltage in the range from 10V to 30V. Consider load resistance of 10KΩ
Sketch the output voltage of the circuit shown in FigureP13.74 to scale versus time. Sometimes, an integrator circuit is used as a (approximate) pulse counter. Suppose that the output voltage is −10 V. How many input pulses have been applied (assuming that the pulses have an amplitude of 5 V and a duration of 2 ms, as shown in the figure)?
Find the following: DC gain, inductor current ripple and output voltage ripple: For DC-DC Buck converter: 1-Draw all circuits in all position 2-Sketch the transistor current waveform 3-Derive analytical expressions for the dc components of the capacitor voltages and inductor currents. 4-Derive analytical expressions for the peak ripple magnitudes of the input filter inductor current and capacitor voltage.
Briefly comment on the significance of controlling the bandwidth of frequencies anamplifier intends to amplify.

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS