Q4/ The following offsets were'taken from a chain line to a hedge:Distance (m)01020304080120160200210220Offsets (m)211525109161716202622Compute the area between the chain line and the end offsets by:(a) Trapezoidal Rule.(b) Simpson's Rule.

Trapezoidal rule - Area = A = dh1+hn2+h2+h3+.......+hn-1 d = difference in distance. h = offset…

Q4/ The following offsets were'taken from a chain line to a hedge: Distance (m) | 0 10 20 30 40 80 120 160 200 210 220 Offsets (m) 21 15 25 10 16 17 16 20 26 22 Compute the area between the chain line and the end offsets by: (a) Trapezoidal Rule. (b) Simpson's Rule.

Q4/ The following offsets were'taken from a chain line to a hedge: Distance (m) | 0 10 20 30 40 80 120 160 200 210 220 Offsets (m) 21 15 25 10 16 17 16 20 26 22 Compute the area between the chain line and the end offsets by: (a) Trapezoidal Rule. (b) Simpson's Rule.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A closed five-sided field traverse has the following interior angles: A = 110° 27’; B = 130° 52’ ; C…

A: The given traverse is closed and five sided. Therefore we can determine the missing interior angle…

Q: A slope distance of 465.89m is measured between two points with a slope of 12o34’. What is the…

Q: 3. From the given data of a compass survey, compute the corrected bearing of line DE. LINE FORWARD…

A: Given: Line Forward Bearing Backward Bearing A-B N 30° 30' W S 32° 15' E B-C S 80° 45' W N…

Q: In the Given Tabulation LINE BEARING LENGTH S04°22'40" W 1-2 48.19m 2-3 S75°14'00" 35.69 W…

A: A closed traverse is given with length and bearing. It has been asked to find Traverse diagram…

Q: Prob.7. Perpendicular offsets at 50 m intervals to the hedge are 10.6, 15.4, 20.00, 15.00, 16.00,…

A: (i) It is required to determine the area using the average ordinate rule.…

Q: From the given data of a closed traverse. Lines Bearing N 15 18' E S 85°46' E S 18°30' W Distances…

A: Lattitude and Departure signs : N-E : Both positive S-E : Lattitude negative , Departure positive…

Q: Problem 4 The interior angle of a six sided closed traverse were measured as follows: A=68°16',…

Q: From the following traverse, Line Bearing Azimuth Distance 1-2 N48°30'W 131°30' 81.00 m 2-3 N77°00'E…

Q: 3. Given the following data of a closed traverse LINE DISTANCE (m) BEARING 1-2 31.20 N 15°24' E 2-3…

A: As per the company guidelines, we are obliged to answer only one question at a time. Therefore,…

Q: 2 You are given a closed traverse ABCD with the observed whole circle bearings as given below. Line…

A: The difference between FB and BB of line should be equal to 1800 . If it is less than or greater…

Q: A series of perpendicular offsets were taken from a transit line to a curved boundary line. The…

A: Using Simpson's 1/3rd rule

Q: The interior angle of a six sided closed traverse were measured as follows: A=96°16', B=135°28',…

Q: Using transit rule, adjust the closed traverse.Compute also the linear error of closure and the…

A: This approach was created to balance a traverse in which the angles are determined with more…

Q: A closed traverse has the following data: Distance Line Bearing Latitude Departure (m) 1081 S…

A: LINE DISTANCE BEARING LATITUDE=Lcosθ DEPARTURE=Lsinθ AB 1081 S73°47'E -301.89 +1037.03 BC…

Q: Given the closed traverse data. Lines Bearing Distance AB N20o E 20.35…

Q: bläs 6 Find the width of the river CD. If .AB=60m River 60 45° A B

A: We will Use Basic Trigonometric Functions to get the Width of River :tanθ=PerpendicularBaseSuppose…

Q: The interior angle of a six sided closed traverse were measured as follows: A=96°16’, B=135°28’,…

A: Here the bearing is given in Quadrantal Bearing System.Hence we need to find out bearings of the…

Q: Q#14: The following perpendicular offsets were taken at 10m intervals from a survey line to an…

A: Given :- The perpendicular offsets were taken at 10 m intervals…

Q: Given the following data of a closed traverse LINE DISTANCE (m) BEARING 1-2 42.2255 N 17°35' E 2-3…

Q: .Given the following data of a closed traverse LINE DISTANCE (m) BEARING 1-2 31.20 N 15°24' E 2-3…

Q: 8. Points B and C are to be laid out from the instrument set up at point A. The bearing and distance…

A: Finding out length of BC and slope.

Q: Q.2 A four-sided closed field traverse has the following angles and side lengths, are as follows:…

A: To Determine a. Balance the field angles b. Compute the bearings or the azimuths c. Compute the…

Q: 26.) Given the following data of a closed traverse LINE DISTANCE (M) BEARING 1-2 42.2255 N 17° 35' E…

A: A closed traverse bearing and length of each side is given in the tabular form as represented in the…

Q: the following offsets are taken from a survey line to a curves boundary line, and the first and the…

Q: Given the bearing of line AB, and the deflection angles of BC, CD, DE and EF. These lines are…

Q: A closed traverse ABCD has the following data: LINE LENGTH BEARING 122.00m 149.00m N 30° E N 60 E S…

A: The traverse is to compute the direction and length of the particular point. The traverse is carry…

Q: 2. Given the observed magnetic bearings (forward and backward) of a closed compass traverse Line…

Q: A series of perpendicular offsets were taken from a transit line to a curved boundary line. The…

Q: EX1: For the given closed traverse shown, Bearing S 35°30' W Lines Distance А-В 44.37 m N 57°15’ W N…

A: Step 1

Q: Q/1/..The following offsets were taken at 15 m intervals from a survey line to an irregular boundary…

A: Survey engineering is the branch of civil engineering in which details of land are measured by…

Q: M2-2 MOST PROBABLE VALUE. Measurement of three horizontal angles about a point P are: APB =…

A: As per bartleby policy i can answer only one question at time. Please upload second question again.

Q: Find the resultant Q = 60 N %3D 25° P = 40 N %3D | 20° AT

Q: 1) Using transit rule , adjust the closed traverse.Compute also the linear error of closure and the…

Q: d. Adjust the traverse using Compass Rule e. Adjust the traverse using Transit Rule BEARING DISTANCE…

Q: 1) B.B. of line PQ is N 35° W, Find it's F.B. (ii) F.B. of line AB is 182°, Find it's B.B.…

Q: Irregular Area = 1930 m2 and the offsets from line AB to the Irregular line ( h1, h2, h3 , h4 , h5 ,…

A: Area = A = 1930m2 h1 = 30m h2 = 28m h3 = 15m h4 = 27m h5 = 22m h6 = 13m h7 = 10m

Q: M5-1 SLOPE TAPING. A horizontal distance of 325.75 m is to be established along a line that slopes…

A: As per company guidelines, we can answer only one question. Kindly repost other questions as a…

Q: H.W: From the base line AB, the linear measurements (offsets) are taken to setting out a rectangular…

A: Surveying is the branch of the construction industry in which the measurement between different…

Q: ose traverse has the following data: DURSE BEARING DISTANCE (m) N 9.27° E S 88.43° E N 86.78° E 58.7…

A: To find length and bearing of course 5-1

Q: COURSE LENGTH (m) BEARING / AZIMUTH AB 110.80 32°27' BC 83.60 unknown CD 126.90 188°51' DE unknown…

Q: Using the transit rule, balance the given traverse. Compute for the corrected distance and bearing.…

A: To find AZIMUTH of lines. Latitude and departure. Corrected Latitude and corrected Departure. (Using…

Q: 25) A series of perpendicular offsets were taken from a transit line to a curved boundary line. The…

Q: Recorded Information for the Closed Traverse ABCD COURSE LENGTH* BEARING N 30° E N 60° E S 10° W N…

Q: PROBLEM 2: The following offsets were taken from a chain line to an irregular boundary line at an…

Q: Given the bearing of line AB, and the deflection angles of BC, CD, DE and EF. These lines are…

A: Refer to the Figure Given Below. i) Line AB is Extended to BI, SInce the deflection of BC is to the…

Q: 1) Using transit rule , adjust the closed traverse.Compute also the linear error of closure and the…

A: Adjustment of Traverse by Transit Rule Latitude = Lcosθ Departure = Lsinθ Correction in LAT =…

Q: Perpendicular offsets are measured at regular intervals of 5 m from a traverse line to a curved…

A: USIng trapezoidal rule

Q: 5. A closed traverse with 5 corners has field measured interior angles at each corner as follows,…

Q: 2. Given the following data of a closed traverse. LINE BEARING DISTANCE АВ N 38°29' E 33.00 BC S…

Q: Find the probable error of the sum and the most probable value of the perimeter

A: To find probable error of sum

Concept explainers

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.

Question

Q4/ The following offsets were'taken from a chain line to a hedge:
Distance (m)0
10
20
30
40
80
120
160
200
210
220
Offsets (m)
21
15
25
10
9
16
17
16
20
26
22
Compute the area between the chain line and the end offsets by:
(a) Trapezoidal Rule.
(b) Simpson's Rule.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Exa . 3 D“:l'[::: 1: the following offsets were taken from a chain line to hedge: | Offset B et I B, 120 160 220 280 . 108 136 182 96 BA& TS 63 46 the hedge and the offset by (iv) Trapezoidal (Ci)o;r;;):tcrdxpe area inc.ludcd between the chain line, id ordinate rule, (ii) Average ordinate rule, (iii) Simpson's rule, rule.
Given the closed traverse data. Lines Bearing Distance AB N20o E 20.35 BC N68oE 18.75 CD S22oE 21.30 DE S40oW 13.35 EF S62oW 9.23 FA Compute the following. Compute the bearing and distance of line FA Compute the area of the given traverse
From the given traverse result: Lines Bearing Distance AB S35o30’W 44.37m BC N57o15’W 137.84m CD N1o45’W 12.83m DE ? 64.86m EA ? 106.72m Compute the following: The bearing of line DE The bearing of line EA Compute the area of the lot in acres.
At regular interval of 5 meters along line AB, the measured offset distances from the line AB to the edge of the stream are: 6.5, 7.3, 12.1, 12.7, 14.5, 16.0, 18.6, 18.5, 16.4, 15.9, 14.7, 13.5, 12.75, 12.5, 9.7 and 2.0. What is the area between line AB and the stream? a. Area using Trapezoidal Ruleb. Area using Simpson’s 1/3 Rule
Give right answer and please solve it quickly... (1) B.B. of line PQ is N 35° W, Find it's F.B. (ii) F.B. of line AB is 182°, Find it's B.B. (iii) R.B. of line XY is S 37° W, Find it's W.C.B. (iv) W.C.B. of line MN is 272°, Find it's R.B. (v) If F.B. of line PQ is S 17° E and F.B. of line QR is N 47° E, Find angle PQR. (vi) If F.B. of line XY is 237° and F.B. of line YZ is 320°, Find angle XYZ. (vii) If F.B. of line AB is 210° and. F.B. of line AC is 120°, Find angle
determine Mn knowing that Es=0.005294
x^2+9y^2=r^2 orthogonal trajectory y=Cx^n
1. A triangular piece of land ABC (clockwise) has the following directions in azimuth fom South. AB = 225o23’, BC = 325o20’, CA = 100o10’ Compute the interior angles. 2. An open traverse ABCDE has following azimuth from South: AB = 250o30’ BC = 280o20’ CD= 210o45’ DE = 150o50’ Required: Deflection angles at points B,C, and D. Draw the figure properly.
Closed traverse ABCD has the following bearings: AB = N 45°20′ E; BC = S 47°32′ E; CD = S 14°55′W; DA =N68°00′W Compute the interior angles and provide a geometric check for your work. Find the following interior angles A, B, C, D
Two Straight lines AB and BC intersect at chainage 7827 m, the deflection anglebeing (49)ᴼ . It is desired to connect these two straight lines by a simplecurve of 4ᴼ. Calculate the following: 1) Length of Curve. 2)Apex Distance
Compute the latitudes and departures for the sides of the traverse shown in the figure. Determine the error of closure and precision of the traverse. Note: there is an error in the textbook. The length of line CA should be 778.26 ??, with a bearing of ?82°44’?(as shown in the figure below).
A1) Answer the following; a. From station 0+040 with a center height of 1.2m fill, the ground line makes a uniform slope of 6.5% to station 0 + 100, whose center height is 3.5m. Find the grade of the finished roadway. b. Station of P.T of a compound curve is at 15+480.14, l1= 30degrees, l2=36 degrees, D1= 4 degrees, and D2=5 degrees. what is the stationing of P.C.C? use arc basis.