Q4. An insulated tank of 0.4 m² initially contains saturated vapor at 350 kPa is attached to a line containing steam at 1.4 Mpa and 300°C through a valve. Steam flows into the tank until the pressure in the tank reaches 1.4 Mpa and then the valve is closed. Assuming no heat flows from the steam to the tank. Determine the final temperature of steam in the tank and the amount of steam enters.

Q4. An insulated tank of 0.4 m² initially contains saturated vapor at 350 kPa is attached to a line containing steam at 1.4 Mpa and 300°C through a valve. Steam flows into the tank until the pressure in the tank reaches 1.4 Mpa and then the valve is closed. Assuming no heat flows from the steam to the tank. Determine the final temperature of steam in the tank and the amount of steam enters.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 0.3-m3 rigid tank initially contains refrigerant- 134a at 14°C. At this state, 55 percent of the mass is in the vapor phase, and the rest is in the liquid phase. The tank is connected by a valve to a supply line where refrigerant at 1.4 MPa and 100°C flows steadily. Now the valve is opened slightly, and the refrigerant is allowed to enter the tank. When the pressure in the tank reaches 1 MPa, the entire refrigerant in the tank exists in the vapor phase only. At this point the valve is closed. Determine (a) the final temperature in the tank, (b) the mass of refrigerant that has entered the tank, and (c) the heat transfer between the system and the surroundings.
A saturated liquid–vapor mixture of water, called wet steam, in a steam line at 1600 kPa is throttled to 50 kPa and 100°C. What is the quality in the steam line? Use data from the steam tables.
1.) Steam enters an adiabatic turbine ( isentropic process ) at 300 C at 600 Kpa it exists as saturated vapor at 40 Kpa. Determine the work done. 2.) If 0.45 kg of steam at 101.3 Kpa and 63% quality is heated isentropically ,at approximately what pressure will it reached the saturated vapor state?
3.9 m3/s of saturated water vapor enters a compressor at 250 kPa and leaves it with a pressure equal to 1400 kPa. Assume the process to be isentropic. Determine the work rate necessary to the nearest kW.
Q2: One mole of air at P: and temperature Ti is compressed at constant volume till its pressure doubled. Then it is allowed to expand reversibly and isothermally to the original pressure and finally restored to the originol temperature by cooling at constant pressure. Sketch the processes on a P-V and calculate the net work done by the
Determinethecapacityoftheheatingcoilwhen1.5m3/sofmoistairis heated from 21C db, 15C wb with a value of 20C. If the coil uses hot water and enters at 85C and exits at 75C. Determine the mass flowrate of the water
The air in an insulated, rigid compressed-air tank whose volume is 0.5 m3 is initially at 2400 kPa and 20°C. Enough air is now released from the tank to reduce the pressure to 2000 kPa. Following this release, what is the temperature of the remaining air in
A 20 kg/s steam enters a turbine at an initial enthalpy of 2456kJ/kg and exits at 1987 kJ/kg. If the kinetic energy of the steam decreases by 10 kJ/s, how much is the turbine work? Draw a schematic diagram,andthen plot the state/s and process, whichever is applicable in a t-sdiagram
Steam at 300 kPa and 200C undergoes an isentropic process where it expands until it becomes 30 kPa. Solve for the change in enthalpy.
As shown in the figure, a 320-ft3 tank contains 25 lb of H2O initially at 30 lbf/in2. The tank is connected to a large steam line carrying steam at 200 lbf/in2, 450oF. Steam flows into the tank through a valve until the tank pressure reaches p2 = 100 lbf/in2 and the temperature is 400oF, at which time the valve is closed.
At 645.3 kPa and 151.2°C, steam leaves an industrial boiler. When the calorimeter pressure reaches 104.3 kPa, a part of the steam is fed through a throttling calorimeter and expelled to the atmosphere. If the steam temperature at the calorimeter is 113.8°C, a. how much moisture is exiting the boiler container? b. If the mass of the saturated liquid is 15 kg, calculate the mass of the saturated vapor. @ 645.3 kPa and 151.2°C: hf = 624.56 kJ/kg hfg = 2123.3 kJ/kg @ 104.3 kPa and 113.8°C: h2 = 2506.7 kJ/kg
Saturated steam at 0.16 MPa is compressed in an irreversible adiabatic process with an efficiency of 80.24%. For a final pressure of 0.45 MPa, determine (a) the final and initial entropies and (b)the ideal and actual temperatures of compressed steam. (Hint: Use Mollier Chart)