Q4. Draw a neat diagram and explain the uses of following tools in welding shop a) Tongs b) Ground clamp c) Angle grinder d) Chipping hammer

Q: What is the method of design called?

A: A design method is a set of various procedures that are carried out while designing planning to…

Q: 1. Give the definition of Traditional Welding Machine.

A: Defination:- Traditional welding machine which is also called an Acr welding machine where…

Q: Briefly explain the anodizing process with a neat diagram. b). Write the application of anodizing…

A: The electrochemical process of transforming the metal’s surface into somewhat more durable, esthetic…

Q: design project to design a plastic shredder machine that will shred 100 2liter plastic bottles per…

A:

Q: FIGURE 21.11 (a) Forces acting in the cutting zone during two-dimensional cutting: note that the…

A: The main aim of lubrication in machining is to reduce the frictional forces. To determine the effect…

Q: When cutting a beam at a point within a distributed load, you should always

A: The uniform distributed load is the force applied on an area while the point load is the force…

Q: explain the general tips or guidelines for a safe workshop

A: A workshop is defined as a space or structure where work is done, or a seminar or series of…

Q: draw a simple diagram to illustrate the process of forming and joining for car manufacturing process

A: A forming process used in car manufacturing is rolling used to make sheets of car. The diagram is as…

Q: 3. Identify and explain the safety procedures and precautions that should be followed for fire…

A: A safety process is a step-by-step guide on how to carry out a job. The safety protocol is a…

Q: How are symbols of work and heat determined?

A:

Q: With a neat diagram briefly explain about riveting process. Write any two applications of riveting.

A:

Q: Introduction for shaper work process please elaborate in 200 words

A: Shaper is a material removal machine of reciprocating type motion, and used for producing flat…

Q: Mechanical assembly is carried using ___________ components. a. Nuts and bolts. b. Gas welding c.…

A: Mechanical assembly  means joining of two or more parts together. In other words Mechanical assembly…

Q: Flash is associated with ________manufacturing process. a. Joining and assembly process b. Metal…

A: Flash is basically the the excess material which is attached to a formed (that is molded, forged…

Q: Gas welding and picture and hand drawing . !

A:

Q: What is the key to preventing accidents in a weldingshop?

A: Following the safety rules, regulations and the procedures for the welding process are the key…

Q: The example for Heat treatment process is ___________. a. Etching b. Annealing c. Turning d. Gas…

A: We have to written  The example o for Heat treatment process is

Q: What two things were iron used for in African communities? O making tools and weapons O making golf…

A: African communities used iron for making tools and weapons.

Q: what is welding in manufacturing process

A: Welding is the manufacturing process in which two metals or thermoplastics are joined together by…

Q: Define welding?  2/ Explain with neat sketch, “Gas welding” process.

A: Welding is a fabrication process in which two similar or different metals are joined with the help…

Q: create 3 simple flow chart on how stainless steel, car tires, and coca cola is manufactured.

A: Flow chart for stainless steel:

Q: Draw the neat diagram of slotting machine and label all its parts.

A: To Draw: The neat diagram of slotting machine and label all its parts. Explanation: Slotting…

Q: Q3. What is a welding process? Write the classification of welding process write any two advantages…

A:

Q: 2. Working principle of Welding Machine

A: The welding machine works on the principal of conversion of electric energy into heat energy or into…

Q: For wire drawing operation, the work material should essentially be (a) ductile (b) hard (C)…

A: A wire drawing is a process in which the diameter of wire is reduced in several steps and the most…

Q: 4% if order quantity is 2000 or more. If the total cost is to be minimized, the retailer should

A: Given data; annual demand for window frames is =10000 each frames cost=Rs 200 ordering cost=Rs 300…

Q: Explain the term useful service life?

A: While purchasing any equipment for industrial/household purpose, one of the most sought-after…

Q: 2. Give the definition of Modern Welding Machine.

A: Conventionally, welding is defined as a permanent joining process of two metals by the application…

Q: 1. What type of tool is it? 2. What is its main purpose? 3. What secondary functions does the tool…

A: 1.A hammer is a tool, usually a hand tool, that consists of a weighted "head" attached to a long…

Q: Could you please help me with my hw? Thank youu

A: Given that:  x = 3 sin 3t + 4 cos 3t   To prove :    a = - ω2x

Q: a) Explain the following drilling machine parts . i). Work table ii) Drill bit b). Assume you are an…

A: A drilling machine is defined as a machine that is utilized to drill holes on specific specimens.…

Q: 6) The source of energy in Explosion welding process is Mechanical energy Chemical energy Radiation…

A: The explosion welding process is used to produce the bonding between the similar metals and it does…

Q: Explain with neat sketch of “Etching” the surface finishing process.

A: Etching : It is the process of preparing a material before introducing it to a microscope, Etching…

Q: Define the concept of mechanic of materials ?

A: Given Data⇒ Mechanics of materials

Q: C- Draw a neat sketch of a SCARA robot and clearly indicate all joints’  variables and types on the…

A: c)

Q: a) What is the difference between One and Two Points Perspective?

A: All lines in the image that are not vertical or horizontal disappear into one point in one…

Q: 1. Give the definition of Tradional Welding Machine

A: Traditional arc welding machine

Q: The costs of common tools, general supplies and equipment maintenance are considered…

A: Given: The costs of common tools, general supplies and equipment maintenance are considered…

Q: Which of these machining processes does not belong to Nontraditional ones?   a)Electron beam…

A: In non traditional machining methods, the general sources of energy would be heat, electricity,…

Q: (i) List the types of maintenance activities? (ii) Explain any one maintenance activity with its…

A: Maintenance is defined as the activity to check and function the machine or mechanical equipment to…

Q: Discuss the welding process and List the tools used in welding process. Identify its application and…

A: Welding is a fabrication process whereby two or more parts are fused together by means of heat,…

Q: Sheet metal Air Duct Objective: To perform cutting and forming processes on a sheet metal to produce…

A:

Q: what is welding in manufacturing process  b) give sum examples and types of welding c) state the…

A: a.In a manufacturing process,Welding is defined as an operation used to join two or more metal…

Q: 1. Give the definition of Tradional Welding Machine.

A: Welding process: It is a permanent joining process with the help of heat and with or without using…

Q: List four industries that depend on machining.

A: Industries  that depend on machining are ;

Joining Processes

It is the process of permanent or temporary joining of two metal pieces with the help of heat or pressure. Two metal parts are assembled by applying an energy source for the formation of a single unit. The obtained joined metals cannot be fragmented easily with the application of any force.