Q4. For the op-amp circuit as shown below, given that Rs = 52.5 k2, RL = 9 k2, R1 = 2 k2. = 13 k2, R2 = 13 k2, R3 = 3.5 k2, R4 = 4 k2, R5 %3D %3D Vs Rs Vo, R1 Vp2 +, Vo R2 Vn2 Vny RL R3 R4 R5 (Q4.1) Determine the voltage gain G1=Vo1/Vs: (V) 4.714285714 Submit Answer Incorrect. Tries 1/5 Previous Tries (Q4.2) Determine the voltage gain G2=vo/vs: Submit Answer Tries 0/5

Q4. For the op-amp circuit as shown below, given that Rs = 52.5 k2, RL = 9 k2, R1 = 2 k2. = 13 k2, R2 = 13 k2, R3 = 3.5 k2, R4 = 4 k2, R5 %3D %3D Vs Rs Vo, R1 Vp2 +, Vo R2 Vn2 Vny RL R3 R4 R5 (Q4.1) Determine the voltage gain G1=Vo1/Vs: (V) 4.714285714 Submit Answer Incorrect. Tries 1/5 Previous Tries (Q4.2) Determine the voltage gain G2=vo/vs: Submit Answer Tries 0/5

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

Design an op-amp circuit to yield the relationship shown in each equation. Vo = V1 + 10V2 – 30V3 – 100 V4a.) Rmin = 6kΩb.) Rin = 6kΩ
Design V0 = 9V1 +7 V2 -2 V3 Constraints: Use 2 Op-Amps
Q3. For the op-amp circuit shown below, find the value of vO, where R1 = 20 Ω, R2 = 12 Ω, R3 = 15 Ω, R4 = 19 Ω, Rf = 17 Ω, VS1 = 12 V, and VS2 = 9 V.
as ap q4b
Figure Q. 3(b) shows an op amp circuit for linear amplifier application. (i) Determine the value of current I3.(ii) Find the value of R if the output current, Io is given as 2 mA.(iii) Explain what will happen to output voltages, V01 and V02 if the supplyvoltages, +VCC and -VCC are connected to +10V and -10V.
3.Discuss two DACs with circuit diagram and proper equations. List their pros and cons
Design an op-amp circuit that can perform this operation: V0=1/2v1+2/5v2-4/3v3
Write down the characteristics of an ideal op-amp. Design an op-amp circuit with inputs v1, v2and v3 such that v0= -3v2 + 0.5v1 + 2v2.
Using inverting, non-inverting, Buffer, or Summer op_amps circuit to design the following equation Vo = 3 V1-3 V2-4 V3
here im asked to find vx the way it was solved is that a node A was taken just before the op amp and nodal analysis aka kcl was applied and the node after it was called v0. but how did we name the first one A and the 2nd one v0? on what basis? also if im asked to get vx how do i think of taking the node A to get an equation so i can get Vx? what should i look for? im really bad at knowing what nodes to take and apply kcl or nodal analysis on to reach my desired solution so can you please help me with that? at the end of the answer it said vx=v0.2R / R+2R getting -2rA0 please can you address all my points so i can understand what and how to look for when solving this type of question?
PRACTICALPERSPECTIVE_ An engineering project managerhas received a proposal from a subordinate who claims the circuit shown could be used as a treble volume control circuit ifR4≫R1+R3+2R2. The subordinate further claims that the voltagetransfer function for the circuit isH(s)=VoVs =−{(2R3+R4)+[(1−β)R4+Ro](βR4+R3)C2s}{(2R3+R4)+[(1−β)R4+R3](βR4+Ro)C2s} where Ro=R1+R3+2R2. Fortunately the project engineer has an electrical engineering undergraduate student as an intern and thereforeasks the student to check the subordinate’s claim.The student is asked to check the behavior of the transfer function asω→0; as ω→∞; and the behavior when ω=∞ and β varies between 0 and1. Based on your testing of the transfer function do you think the circuitcould be used as a treble volume control? Explain.
When OP-AMPs are considered ideal in the circuit: a) What is V voltage? b) What is the equivalent resistance of the region inside the rectangle?