Q5: Design a full-wave bridge rectifier with 1k2 load. The rectifier operates from A.C supply of 220v (rms) and 50HZ through 20-to-1 step down transformer. What is the peak value of the rectified output across the load and the fraction of a cycle does each diode conduct? What is the PIV of the used diodes. The diodes can be modeled to have 0.8v voltage drop for any current.

Q5: Design a full-wave bridge rectifier with 1k2 load. The rectifier operates from A.C supply of 220v (rms) and 50HZ through 20-to-1 step down transformer. What is the peak value of the rectified output across the load and the fraction of a cycle does each diode conduct? What is the PIV of the used diodes. The diodes can be modeled to have 0.8v voltage drop for any current.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

A half wave rectifier circuit with a 1K ohm load operates from a 120V rms 60-Hz household supply through a 10-to-1 step down transformer. It uses a silicon diode that can be modeled to have a 0.7V drop for any current. What is the peak voltage of the rectified output? For what fraction of a cycle does the diode conduct? What is the average output voltage? What is the average current in the load? Thanks for any help.
A full-wave bridge rectifier with a 236.86V p-p sinusoidal input has a load resister of 2KΩi. Draw the wave form that the load resistor R would see. ii. Assuming diodes are ideal, what is the dc voltage available at the load resistor? iii. What is the dc voltage available at the load if silicon diodes are employed? iv. Calculate the maximum current flow through the Diode D4 during conduction.
Draw the circuit diagram of a single phase full-wave uncontrolledrectifier with R-load. Describe its principle of operation. Draw thewaveforms of: input voltage, voltage across the load, current throughthe diodes and their voltage. Write the expressions for: the averageoutput voltage Vd, the maximum reverse voltage across the diode and thestandard transformer power. Describe what the difference will be if acapacitor is added in parallel with the load at the output.
a) Use the diode’s characteristic equation,ID=Is exp(VD/VT), to determine the currentsourceIso that the output voltage is 1.5 V. b) If a load is attached to the output that draws 1 mA, what is the output voltage? c) If the circuit heats up to 40◦C, what is the output voltage without a load?
A full-wave bridge rectifier with a 12V (pk) sinusoidal input has a load resistor of 20 k. (a) If silicon diodes are employed, what is the dc voltage available at the load? (b) Determine the required PIV rating of each diode. (c) Find the maximum current through each diode during conduction. (d) What is the required power rating of each diode?
A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance? If a full-wave rectifier is needed?
The npn transistor is connected in an alternate“diode” configuration. Use the transport model equations to show that the i-v characteristics of this connection are similar to thoseof a diode as defined. What is thereverse saturation current of this “diode” if IS =5 × 10−16 μA, βF = 60, and βR = 3?
Describe the operating principle and characteristics of a typical Zener diode found in the market place, including examples of their common applications. The circuit shown below is to be used to provide a stabilised output to the load. The Zener diode characteristic is also shown on the next page. Find the load voltage (VL) and source current (IS) if the battery voltage is 18 V, series resistance is 1.4 KΩ and load resistance is 11 KΩ. Additionally, determine the value of the source resistance (R) if the Zener diode is at the threshold of activating in its reverse bias. Comment on the purpose of having this value of R in the circuit.
Two identical Schottky diodes are connected in series, one in the forward and the other in reverse direction, see figure. Assume the reverse saturation current, IS, of each diode to be known. Derive he current-voltage curve I(V) of this circuit. Plot it with the ratio I / IS on the y-axis and V / Vth on the x-axis. Make sure to cover a broad range of voltages, say, from –10 Vth to 10 Vth.
The power in the rectifier circuit given by Vs = 220 sen(??)V and the four diodes with an ideal behavior R = 1kΩ. Explain the behavior of the converter during the negative semi-cycle of the tension Vs. To analyse the behavior, explain which way the electric current should circulate, what is the tension in the load and the diodes, what is the duration of the semi-cycle, and what is the value of the electric current in the load and the diodes.
Design a half-wave rectifier power supply to deliver an average voltage of 9 V with a peak-to-peak ripple of 2 V to a load. The average load current is 100 mA. Assume that ideal diodes and 60-Hz ac voltage sources of any amplitudes needed are available. Draw the circuit diagram for your design. Specify the values of all components used. Repeat Problem P9.54, assuming that the diodes have forward drops of 0.8 V.
a. For the circuit given in the figure on the right, set VRL to 10Find the maximum and minimum value range of RL and IL that will hold in volts.b. As a regulator, without damaging the diodethe maximum diode required to operateCalculate the power.