Q5 | A 6.00-kg block and an 8.00-kg block are connected as shown. When released, the 6.00- kg block accelerates downward and the 8.00-kg block accelerates to the right. After each block has moved 2.00 cm, the force of gravity has done (Prove and tick below.) 8.00 kg A. more work on the 8.00-kg block than on the 6.00-kg block. B. the same amount of work on both blocks. C. less work on the 8.00-kg block than on the 6.00-kg block. D. comparably high work on the 8.00-kg block than on the 6.00-kg block. 6.00 kg

Q5 | A 6.00-kg block and an 8.00-kg block are connected as shown. When released, the 6.00- kg block accelerates downward and the 8.00-kg block accelerates to the right. After each block has moved 2.00 cm, the force of gravity has done (Prove and tick below.) 8.00 kg A. more work on the 8.00-kg block than on the 6.00-kg block. B. the same amount of work on both blocks. C. less work on the 8.00-kg block than on the 6.00-kg block. D. comparably high work on the 8.00-kg block than on the 6.00-kg block. 6.00 kg

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

16- A helicopter with a mass of 72kg is towed by a rope 15m perpendicularly from the ocean surface. The pilot's acceleration is g/10. What is the work (J) done on the pilot by the force exerted by the helicopter? (g=9.80m/s2)
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Block D, initially at rest, having a W = 30 lbf , is supported within the system shown, with x = 13.2 ft. Neglecting the mass of the pulley and the cord on the system, determine the eventual height h after a force P = 60 lbf is applied to make the block rise by ∆sD = 0.625 ft at t = 2.5 s. NOTE: Use Force-Mass-Acceleration (FMA) Method.
By using a forked rod, a smooth cylinder C having a mass of 0.5 kg is forced to move along the vertical slotted path (r = 0.4 θ) m, where θ is in radians. If the angular position of the arm is θ = (0.3 t3 ) rad, where t is in seconds. The cylinder is in contact with only one edge of the rod and slot at any instant. Find "the force of the rod on the cylinder at the instant t=2s" Find "the normal force of the slot at the instant t=2s" Find the "radius of curvature at t=2s" Find the "ψ angle at t=2s"
A body of 3kg moving in the frictionless xy plane started its motion from the center of the coordinate system with a velocity of Vilk=(2î+j)m/s. The object is oriented to the point given by rson=(10î+j)m by the effect of forces F1=(2î+7j)N and F2=(2î-5j)N. A) Find the work done by F1 and F2 forces. B) What is the velocity when the object reaches its rend position?(g=9.8m/s^2)
A block of mass m1 = 3.60 kg on a frictionless inclined plane of angle 30.0° is connected by a cord over a massless, frictionless pulley to a second block of mass m2 = 2.00 kg hanging vertically. (a) What is the magnitude of the acceleration of each block? m1 = m/s2 m2 = m/s2 (b) What is the direction of the acceleration of m2? m2 accelerates downwardsnot enough information m2 accelerates upwards (c) What is the magnitude of the tension in the cord? N
A 4.6-kg block is pushed 2.3 m up a vertical wall with constant speed by a constant force of magnitude F applied at an angle of ? = 30° with the horizontal, as shown in the figure below. If the coefficient of kinetic friction between block and wall is 0.30, determine the following. A figure, drawn from a side view, shows the right side of a rectangular block pushed up against a rough, vertical wall. A force vector F acts on the block and is represented by a diagonal rrow pointing up and to the right, toward the center of the block's left side. The arrow forms an angle ? with the horizontal. (a) the work done by F J(b) the work done by the force of gravity J(c) the work done by the normal force between block and wall J(d) By how much does the gravitational potential energy increase during the block's motion? J
In the given figure below, a 3.0 -kg block is sliding down a 60o-rough incline. The speed of the block is 1.68 m/s at the instant it is 5.25 m from an uncompressed spring located at the other lower end of the incline. The spring has a spring or stiffness constant of 120 N/m and the coefficient of kinetic friction between the block and the incline is 0.35. (a) At what speed (in m/s) will the block strike the spring? (b) What would be the maximum compression (in m) of the spring?
F = (128)(s+1)N (to right) and Va = 1.8 m/s (to right) Every block is 25 kg.
Dynamics Question If the normal acceleration of the rods is just w^2 * 1.5m, is the normal acceleration of the 50-kg bar just w^2* 2m?
4. A concrete weight of 125 kg is released from standstill and a log of mass 200 kg is moved along an inclined area of 30° to the horizontal.When the concrete weight is moved down 5 m, find that 1. What is the speed of the log? 2. What is the movement time of the concrete drum?
Khufra works at a spring factory and he was assigned to test a certain spring, whose constant is 50 N/m attached to a 50-kg block in an incline (©=30°). With the spring initially at equilibrium position, the block was pushed 0.3 meters up the incline by a 50-N external force applied parallel to the path. The coefficient of kinetic friction is 0.30. d) How much work is done by the block (in Joules) on the spring? e) How much work is done by the applied push on the block? f) How much work is done by friction?
Khufra works at a spring factory and he was assigned to test a certain spring, whose constant is 50 N/m, attached to a 30-kg block in an incline (θ=30°). With the spring initially at equilibrium position, the block was pushed 0.5 meters up the incline by a 50-N external force applied parallel to the path. If the coefficient of kinetic friction is 0.5, determine the: a) normal force (in Newtons) b) work done by the spring (in Joules)