Q5: The 15 kg cylinder rotates with an angular velocity of 40 rad/s. If a force F = 6 N is applied to the AB bar, as indicated, determine the time required to stop rotation. The coefficient of kinetic friction between the bar and the cylinder is 0.4. Disregard the thickness of the bar. F = 6N 400 mm- 500 mm B 150 mm-

Q5: The 15 kg cylinder rotates with an angular velocity of 40 rad/s. If a force F = 6 N is applied to the AB bar, as indicated, determine the time required to stop rotation. The coefficient of kinetic friction between the bar and the cylinder is 0.4. Disregard the thickness of the bar. F = 6N 400 mm- 500 mm B 150 mm-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The drum, with radius R = 1.9 m, is given an initial counterclockwise angular velocity ω0. The drum is kept from rolling towards the left by a smooth vertical slot acting on a thin rod which passes through its centre. A vertical force (where C = 38, k = 1.7 and t denotes time in seconds) is being applied to a cord wrapped around the inner hub, with radius r = 0.7 m, of the drum. If the frictional coefficient is μk = 0.62 and the change in the angular momentum about O is ΔHO = 238 kg.m2/s (counterclockwise) during the first 2.3 seconds, determine the mass of the drum. (The mass of the cord and the thin rod may be regarded as negligible.) a)214.2 kg b)68.28 kg c)19.83 kg d)109.6 kg e)69.86 kg
The mass m = 5.0 kg resting on a frictionless horizontal table is connected to a horizontal spring with stiffness constant k = 170 N/m. The mass is pulled a distance to the right so that the spring is stretched a distance x0 = 1.3 mm initially, and then the mass is released from rest. e)? g)?
A brake mechanism is used to lower body A with a constant velocity of 3.0 m/s. The coefficient of friction between the brake and drum D is 0.40. Neglect the weight of the brake. Determine the mass of body A and the power dissipated by the brake. (hint: the normal force between the brake the and disk is not 1200 N)
A mass of 20 kg is suspended from a spring of stiffness 10000 N/m andthe vertical motion of mass is subjected to coulomb friction of magnitude50 N. if the spring is initially displaced 5 cm downwards from its staticequilibrium position. Determine the number of cycles before the bodycomes to rest.
The desk has a weight of 54 lblb and a center of gravity at GG. The coefficients of static and kinetic friction at AA and BB are μsμs = 0.5 and μkμk = 0.2, respectively. (Figure 1) Determine the initial acceleration of a desk when the man applies enough force FF to overcome the static friction at AA and BB. Find the vertical reaction on each of the two legs at AA.
The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P = 100N inclined at 20o with the horizontal. If the 100-N pull is then removed, find the distance the block will travel.
The spring-held follower AB has a mass of 0.4 kg and moves back and forth as its end rolls on the contoured surface of the cam, where r = 0.15 m and z=(0.02cos2θ)m. The cam is rotating at a constant rate of 30 rad/s. The spring is uncompressed when θ = 90. Determine the maximum force component FzFz the follower exerts on the cam. Determine the minimum force component FzFz the follower exerts on the cam.
4-The 20-g bullet is fired horizontally at 1400 m/s into the 350-g block resting on a smooth surface. If the bullet becomes embedded in the block, what is the velocity of the block immediately after impact
(The complete question is in the picture) Consider a 2.0 [kg] box that is attached to two identical springs that are in their relaxed state when the block is centered on the frictionless horizontal floor. The box is pressed to the left and then was released from rest as shown in the figure. If work done by the left spring is Wby spring = 25 [J], what is the speed of the boxas it passes the center x = 0? A. 8.2 [m/s]B. 7.1 [m/s]C. 3.5 [m/s]D. zero
The position of the small 0.68-kg blocks in the smooth radial slots in the disk which rotates about a vertical axis at O is used to activate a speed-control mechanism. If each block moves from r = 162 mm to r = 200 mm while the speed of the disk changes slowly from 272 rev/min to 382 rev/min, design the spring by calculating the spring constant k of each spring. The springs are attached to the inner ends of the slots and to the blocks.
A spring is stretched 175 mm by an 8-kg block. If the block is displaced 100 mm downward from its equilibrium position and given a downward velocity of 1.50 ms, determine the differential equation which describes the motion. Assume that positive displacement is downward. Also determine the position of the block when t = 0.22 s. (Show free-body diagram of the system.)
The figure shows a junction of mass m = 10kg sliding on a rod in a vertical plane. Positioned 1 simpai is stationary and horizontal spring and tensioned Fp = 300N. If the spring constant is k = 1kN/m and the average frictional force between the rod and the junction is F = 30N. Calculate the speed at position 2. (Ans: 3.47m/s)