Q5/ The information in an analog waveform with maximum frequency fmtransmitted over M-level PCM system where the number of quantization levels is M = 16. Thequantization distortion is specified not to exceed 1% of peak-to-peak analog signal.= 3 KHz is to bei)What would be the maximum number of bits per sample that should be used in thisPCM system? (ans,n = 4 bits)What is the minimum sampling rate and what is the resulting bit transmission rate?ii)(ans.r > 24 x 103 bits/sec)

Answered: Image /qna-images/answer/4b906c1f-f0fc-4bf8-b74c-040320682c6b.jpg

Q5/ The information in an analog waveform with maximum frequency fm = 3 KHz is to be transmitted over M-level PCM system where the number of quantization levels is M = 16. The quantization distortion is specified not to exceed 1% of peak-to-peak analog signal. i) What would be the maximum number of bits per sample that should be used in this PCM system? (ans, n = 4 bits) What is the minimum sampling rate and what is the resulting bit transmission rate? ii) (ans.r > 24 x 10³ bits/sec)

Q5/ The information in an analog waveform with maximum frequency fm = 3 KHz is to be transmitted over M-level PCM system where the number of quantization levels is M = 16. The quantization distortion is specified not to exceed 1% of peak-to-peak analog signal. i) What would be the maximum number of bits per sample that should be used in this PCM system? (ans, n = 4 bits) What is the minimum sampling rate and what is the resulting bit transmission rate? ii) (ans.r > 24 x 10³ bits/sec)

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter32: Standby Power Systems

Section: Chapter Questions

Problem 7R: Briefly explain the function of a transfer switch. _____

See similar textbooks

Similar questions

1. What are the two ways of generating DSB_SC.2. What are the applications of balanced modulator?3. What are the advantages of suppressing the carrier?4. What are the advantages of balanced modulator?5. What are the advantages of Ring modulator?6. Write the expression for the output voltage of a balanced modulator?
7. The advantage of a differential phase-shift keying (DPSK) system is that_____________ is (are) not required.A. carrier synchronizerB. voltage-controlled oscillatorsC. upper and lower sidebandsD. carrier recovery circuitry
For question 1, The instructor asked what is an approach to modulate a PWM signal and what is an approach to demodulate a signal. Thank you. Explain one approach for PWM modulation and detection (demodulation). Please draw the required circuits and diagrams.
In a binary PCM system with uniform distribution signal, the average output signal-to-quantization-noise ratio is to be held to a minimum of 43 dB. Determine the number of required quantized levels when using (M - law).
How base width vary in Transistor amplifier Circuits? Explain in detail and how this modulation affects the input and output characteristics of CE configuration.
Type your question here Derive the relation between output signal to noise ratio and input signal to noise ratio for SSB-LC system, what would be the relation for S.T case?
What is PWM (Pulse Width Modulation), and how is it used in microcontroller applications? Provide examples of practical use cases for PWM.
In a PCM system, channels of 3 KHz bandwidth are used. If the uniform quantizer has 128 number of levels, then what will be the channel capacity?
For a user signal with a maximum frequency of 10 kHZ: What must be the constant of proportionality kf and the modulation index β so that the bandwidth of the signal modulated in maximum FM is 250 kHZ, if the maximum amplitude of the signal is 5 volts What is its standard deviation in Hz? And calculate the strength of the modulated signal
how to draw the small signal model
Define and explain the difference between analogue and digital signals elaborating on the advantages and disadvantages of both.
Explain why it is important to minimise VCM - Vg, even if the instrumentation amplifierhas excellent common-mode rejection performance.