Q6/ A horizontal bracket ABC shown in Fig. (6) consists of two perpendicular arms AB and BC. Arm AB has a solid circular cross section with diameter equal to 60 mm. At point C a load P1-2.02 kN acts vertically. calculate the maximum tensile stress, the maximum compressive stress, and the maximum in-plane shear stress at point p. LBC = 0,4m. LAB-1m)

Q6/ A horizontal bracket ABC shown in Fig. (6) consists of two perpendicular arms AB and BC. Arm AB has a solid circular cross section with diameter equal to 60 mm. At point C a load P1-2.02 kN acts vertically. calculate the maximum tensile stress, the maximum compressive stress, and the maximum in-plane shear stress at point p. LBC = 0,4m. LAB-1m)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1.) Draw the internal stress and strain diagram of beam considering that the depth of the stress block is greater than the thickness of the flange. f’c =30 MPa, fy=400 MPa and is subjected to a positive bending Mu=140KN-m.
The Beam has a span of 9 m, fixed at both ends and carries a uniformly distributed load of w = 25 kN/m throughout its length. The beam is W 16 x 77 with the following properties: bf = 260 mm tf = 19.3 mm d = 420 mm tw = 11.6 mm Ix = 462. 02 x 106 mm4 Iy = 57.44 x 106 mm4 a. Calculate the maximum bending stress in the beam, in MPA. b. Calculate the average shearing stress in the web, in MPa.
Calculate the normal stress due to flexure at the flange level to web Interface at A. Ixx= 1,241 in^4. Bending moment (M)= 350 ft-kips. Shear (v)= 80 kips.
The copper pipe [G = 5,000 ksi] has an outside diameter of 3.500 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 85 lb-ft/ft along its entire length. Using a = 2.5 ft, b = 3.5 ft, and c = 8.0 ft, determine(a) the maximum shear stress in the pipe.(b) the rotation angle φC at the free end of the shaft.
1-10. A bar of variable cross section, held on the left, is subjected to three forces, P =4 kN, P, = -2 KN, and P, = 3 kN, as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, = 200 mm, A2, = 100mm², and A3, = 150 mm".
The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques shown. A 44-mm-diameter hole has been drilled into portion CD of the shaft. The entire shaft is made of steel for which G = 77 GPa. 1. Calculate the torque in segment CD in N.m. 2. Calculate the torsional shear stress on the surface of segment BC in MPa. 3. Calculate the angle of twist of segment AB in degrees. 4. Calculate the angle of twist of point A relative to point D in degrees.
Given the following data:Cross section: 50mm x 75mmP = 200 kNθ = 15 ° with the x-axis Find the shear stress (in MPa) on plane A-A.
12. The bell crank, which is in equilibrium under the forces P and F = 36 kN inclined at θ= 48o, is supported by a pin at D. Determine the shear stress (in MPa) in the pin if it is 21-mm-diameter. P is not equal to F. Round off to two decimal places.
Determine the moment M in kN-m that must be applied to the beam to create maximum stress of 99 MPa. Where tf = 17 mm and d = 302 mm
From the given simply supported beam below, determine the following: g. The shear stress at the mid-point of the beam.
Member AB has a uniform rectangular cross section of 10 x 24 mm. For the loading Pshown,a) Find reactions at A and B.b) Determine the normal and shearing stresses at Point K and Point H. α (˚) =30 P (kN)=14
Derive the relationship for maximum and minimum shear stress in a wide flange I-Section. Also determine the stresses if shear force is 50kN.