Please solve for support reactions In handwritten format Only ( I also Included Answer which I got ,seems it's Correct)show all the work within hour. question• Find the support Jeautions (for A and B)NeglectBeam weight• I got: RA= 12,500N, RB = - SOON3KN4m水900 N/m6mB

Answered: Image /qna-images/answer/0b48640e-f620-424b-8782-a3031e22cd45.jpg

Answered: question • Find the support Jeautions…

question • Find the support Jeautions (for A and B) Neglect Beam weight D I got: RA= 12,50ON, RB = -500N 3KN JUNE 水 le 900 N/m 4m 6m B TITI

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.11P

See similar textbooks

Related questions

Q: USE SLOPE DEFLECTIONS METHOD Determine the reactions and draw the shear and bending moment…

A: Given: Support settlement of 1 inch at B and 1/4 inch at C Required : Reactions and moment diagram

Q: A truss is subjec Assume AE is constant and use virtual work mathed For deflection of truss.

Q: 1000 mm Section 1 f'c 8-36 Ø fv 32 415 800 mm

A: For the given section we have to find the 1 Depth of neutral axis (C) 2 Depth of compression…

Q: What is the length of the vertical piece halfway between C and D in feet? B 12'-0" A 16'-0" D 16'-0"…

Q: A steel frame is shown in the given figure. A L B L O L/2 C 777 El Constant D If joint O of the…

Q: Determine approximately, the reactions at A, B, C, and D. Use portal frame method.

Q: The centroid of the hatched portion from the base shown in the given figure is d d Half circle

Q: How do you find part C? The answer is 54 degree

A: Resultant couple =2.88N-m = 288 N-cm d=42cm To find value of angle alpha

Q: Draw the V&M diagrams and calculate the largest permissible value of P for the beam and loading…

A: Allowable normal stress in tension=-80MPa Allowable normal stress in Compression=-140MPa To find…

Q: A horizontal curve has a degree of curvature of 10. Find the radius. Select one: a. 180 ft. O b.…

A: Given: Degree of curve=100 To find: Radius of curve.

Q: A W21×101 is used as a compression member with one end fixed and the other end free. The length is…

A: Section-W21×101L=12 ftFy=50 ksi To find- Nominal compressive strength

Q: The uniform A-36 steel bar in Fig. 4-5a has a diameter of 50 mm and is subjected to the loading…

A: To determine the displacement at D

Q: 30 cm diameter concrete pile is driven in a normally consolidated clay deposit 15 m thick. Estimate…

Q: Determine the elastic curve equation for each span and the maximum deflection for each span.

Q: Terminal Velocity 3. Given: Atmospheric pressure = 101.3 KPA Air density = 1.20 kg/cubic meter Size…

A: Atmospheric pressure =101.3kpA , Air Density = 1.20kg/cubic meter Size of rain droplet = 0.6mm ,…

Q: If the resultant of the two forces and couple M passes through point O, determine M 160 mm 0 150 mm…

A: Determine the value of M.

Q: Calculate the plastic modulus Sx of the section shown below. All dimensions are in mm. Note: The…

A: Determine the plastic modulus Sx of the section.

Q: Lane groups are used during signal design to allocate green time among traffic movements at an…

A: Based on the intersection layout provided, the lane groups for the north-bound approach should be…

Q: b) Rotation of a cross-section in point B 1₁ 1 9,1 B

Q: (a) Calculate factored yield strength of the tension member. (b) Calculate factored fracture…

A: Cross-section of angle = L8-41/2 Grade of steel, fy=50 ksi and fu=70 ksi It is sked to determine the…

Q: The hydraulic head that wou quick condition in a sand str 2.3 m, specific gravity 2.67 c 0.67 is…

Q: b) Rotation angle in point C 9,1² A 1 B 1 * C 9₂ = const 21 ▬▬▬ D

Q: Given a simple circular curve, in feet, with the following known information: = 25°10'45" • Da =…

A: I=25°10'45'Da=8°15'00''STA PI = 30+89.45 To find: deflection angle to station 30+00.00

Q: PROBLEM: Project Name: Matabanako Elementary School Project Location: Taytay, Rizal Soil…

A: PROBLEM:Project Name: Matabanako Elementary SchoolProject Location: Taytay, RizalSoil…

Q: 3) A 5-m-high retaining wall is shown in Figure-2. Determine A) Rankine active force per unit…

A: Height of retaining wall = 5 m To find:- A) Rankine active force per unit length and location of…

Q: Return Period 1. Year Maximum depth of precipitation of certain area is presented below. Based on…

A: Year Max. rainfall depth, mm 1995 155 1996 151 1997 189 1998 157 1999 136 2000 280…

Q: The objective of this experiment is to determine the channel bed slope by measuring the variation of…

Q: For the PI Inaccessible problem: Sta. X = 75+50.00, XY =800.00 ft, angle x = 35°00'00", angle y…

A: Given; Sta. X = 75+50.00 XY = 800.00 ft. angle X = 35 DEGREE angle Y = 30 DEGREE Radius for the…

Q: Problem 3. An un-equal leg angle L8x4x½ made of ASTM A242 steel (Fy = 50 ksi, Fu = 70 ksi) is used…

A: Unequal leg angle, L 8 x 4 x 1/2" of ASTM 242 steel, Fy=50 ksi , Fu= 70ksi To Find: (a) Factored…

Q: a. Determine the moment of inertia at the horizontal neutral axis. b. Determine the shear flow at…

A: To calculate the location of horizontal Neutral axis we have y = Ac*yc+Af*yfAc+Af Ac = area of…

Q: Rv is 800 ft. SSD is 360 ft. Central angle of the curve is 50 degrees. Find side clearance distance…

A: Radius to the vehicle's travelled path Rv = 800 ft Stopping sight distance SSD = 360 ft Central…

Q: For a design a concrete which will be exposed to seawater and sulfates in a structure that comprises…

A: Mix design is the selection and designing of proportion of ingredients needed for producing a…

Q: Problem 1. Due to cost and right-of-way constraints, Rv is determined to be 890 ft. Superelevation…

A: The superelevation, e = 0.12 The radius of the curve, R = 890 ft 1 ft = 0.3048 m 1 m/sec = 2.237 mph…

Q: Figura P2.43 75 mm 100 mm 1 8 in 10 in 2.44 La barra rígida AD está soportada por dos alambres de…

A: D = 116 in E = 29 x 106 psi P = 220 lb

Q: 4.9-7 Two 9/16 X 10 plates are welded to a W10 X 49 profile to form a composite section as shown in…

A: W 10 x 49 ( A = 14.4 in2 , Ix = 272 in4 , Iy = 93.4 in4 , d = 10 in) Fy = 50 ksi KL = 25 ft (about…

Q: 10. Determine the reactions at supports. A is pin support ans B is roller 18 ft 2.5 k/ft A -12 ft-…

A: A loaded frame is given and it has been asked to determine support reactions, please refer below…

Q: Part B is Correct . Need help with part C and D

A: The given beam is shown below The unit load is applied at left end of beam. The reactions, shear…

Q: 4.4 Plot the steady-state response of a SDOF structure subjected to the periodic loading shown for…

Q: It is known that the capacity is 3800 veh/h and the jam density is 225 veh/mi. What is the…

Q: Total degree of indeterminacy (both internal and external) of the plane frame shown in the Given…

Q: If the internal radius of a hollow shaft is n times the external radius, then ratio of torques…

Q: Q1 A survey conducted to determine the choice of transportation mode (public bus or private car)…

A: Utility function equation Um = Bm - 0.45C - 0.25T

Q: After placement, the temperature of the concrete was measured and recorded by thermal sensors during…

A: Datum Temperature of concrete mix = -50 C Find: Formwork removal time

Q: A number of different adhesive joint geometries are shown below. Which ONE of the following lists is…

Q: The influence line is for V40- = shear just left of 40'. A load of 0.5 kip/ft is placed from O' to…

A: The influence line is for V40 - shear just left of 40'. A load of 0.5 kip/ft is placed from 0' to…

Q: Two bars AO and BO arc of uniform area 'A' each and are hinged at O as shown in A load W is applied…

Q: a. Check the adequacy of the beam for flexure (2= 1.67) and shear (Cy= 1.0 and £2,= 1.5). b. Check…

Q: A bar of circular cross-section varies uniformly from a cross-section 2D to D. If extension of the…

Q: A concrete pile is 20 m long has a cross section of 0.46 m × 0.46 m. The pile is embedded in a sand…

Q: Version A. A freeway section has 4 lanes on each direction. Lane width = 11 ft. Right-side shoulder…

Question

Please solve for support reactions In handwritten format Only ( I also Included Answer which I got ,seems it's Correct) show all the work within hour.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: given

VIEW

Step 2: calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A bearing pad is a device which is used to support a bridge or other heavystructure in a way that permits the load to shift slightly in a horizontal directionrelative to the ground or foundation. If a horizontal force af 528 kN is applied tothe top surface of the bearing pad, and that a = 700 mm, b = 550 mm, h = 75m and the modulus of elasticity G = 1.25 MPa. Determine the following: a. The average shear stress on the bearing pad.b. The horizontal displacemant of tne bearing pad. Note: Draw the Free Body Diagram, include the proper units and round-off the answers to 3 decimal places.
PROBLEM 1: The homogeneous structure shown weighs 21.45 kN per square meter of cross-section. The structure is subject to horizontal uniformly distributed load P1 and triangularly distributed load P2 perpendicular to side AB. Given: H1 = 9 m; H2 = 6 m; H3 = 12 m X1 = 6 m; X2 = 5 m P1 = 220 kN/m; P2 = 280 kN/m 4 Magnitude of resultant, R 4314.04 5 Angle of resultant direction from x-axis, θx 86.01 6 Distance of resultant from C measured along line CD, X 9.116
The cantilever beam shown is subjected to a couple and 2 forces shown. Replace these couple and forces with an equivalent couple M and single force F at point A. Show solution to the answer FH = 1.64 kN, R Fv = 1.16 kN, D M = 2.22 kN-m, CCW
I. Single-choice questions.: 5. Bridge piers belong to which part of a bridge? ( ) A. Bridge superstructure B. Bridge substructure C. Bridge deck system D. Bridge foundation 6. When calculating the load transverse distribution coefficient (m) near the bearing supports of a simply-supported beam bridge, which kind of calculation method is recommended? ( ) A. Lever principle method B. Hinge joint slab method C. Eccentric compression method D. G-M method
Determine the value of the uniformly distributed loadd "w". What is the numeric value of C1 ( 1st constant)? Dtermine the deflection at midspan.
A beam has a uniform dead load and live load has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at the midspan. (MPa) Properties: Beam width = 263 mmBeam height = 466 mmWLL = 12.52 kN/mWDL = 18.03 kN/mSpan of the beam = 11 mPrestressing force = 323 kNeccentricity = 105 mm
An R.C. Column footing 2.26 m in square shape is to rest 1.5 mbelow level ground level is on cohesive soil. The unit weight is17.6kN/m3. What is the safe load if cohesion is 30kN/m3Factor of safety 2.4? Angle of internal friction 33° by IS code.
P value is 7.1 kN
Step 2 1st condition Bending moment at hinge D =0 Rc*2 = (3*2)*(2/2) Rc = 3 KN Rc = 3 KN (upward) could you explain where these numbers coming? Why that divided by two? and is formula like this: 3kN/m*2m*2m/2m? 2nd condition Bending moment at hinge F =0 RB*2= (3*4)*(3+4/2)-3*7 RB = 19.5 KN RB = 19.5 KN ( upward) Same this formula If you can explain this like drawing this on paper and write where all meters and number come, that would be help me. If you could also tell the direction, where you would calculation them
Solve under 30 min pls i awill give a like
A beam 100 mm x 150 mm carrying a uniformly distributedload of 300 N/m rests on three supports spaced 3 m apart as shownbelow. The length x is so calculated in order that the reactions atall supports shall be the same.
A rectangular beam has a dimension of 210 mm x 260 mm. The simply supported beam is 5-m long and carries a concentrated load of 25 KN at the midspan. What is the maximum flexural stress of the beam? Blank 1 (use two decimal places)