Q6) Air at 30°C flows with a velocity of 6 m/s over a 2.5-mx8-m flat plate whose temperature is 120 degrees * C. Determine the rate of heat transfer from the plate if the air flows parallel to the (a) 8-m-long side and (b) the 2.5-m side.Assignment: solved Question 6, assuming the first 1m is in heat flow across cylinders, spheres

Q6) Air at 30°C flows with a velocity of 6 m/s over a 2.5-mx8-m flat plate whose temperature is 120 degrees * C. Determine the rate of heat transfer from the plate if the air flows parallel to the (a) 8-m-long side and (b) the 2.5-m side.Assignment: solved Question 6, assuming the first 1m is in heat flow across cylinders, spheres

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.20P

See similar textbooks

Similar questions

6.1 Determine the heat transfer coefficient at the stagnation point and the average value of the heat transfer coefficient for a single 5-cm-OD, 60-cm-long tube in cross-flow. The temperature of the tube surface is , the velocity of the fluid flowing perpendicular to the tube axis is 6 m/s, and the temperature of the fluid is . Consider the following fluids: (a) air, (b) hydrogen, and (c) water.
The 100-mmmm-diameter pipe is connected by a nozzle to a large reservoir of air that is at a temperature of 60 ∘C∘C and absolute pressure of 550 kPakPa . The backpressure causes M1>1M1>1, and the flow is choked at the exit, section 2, when L� = 5 mm. Assume a constant friction factor of 0.0085 throughout the pipe. Gas constant for air is R� = 286.9 J/[kg⋅K]J/[kg⋅K] and its specific heat ratio is k� = 1.40. (Figure 1) Determine the mass flow through the pipe. Express your answer using three significant figures.
) A 75 mm-diameter orifice is on the verticalside of a closed tank. The tank rests on a flat groundand the orifice is 0.5 m above the ground. Filled withfour fluids with air on the topmost portion that is undera pressure of 15 KPa, and the rest of specific gravities of0.80, 1.0, and 1.50, respectively, the jet hits the groundat a horizontal distance of 3.75 m. If the liquids have thesame thickness, and the power lost in the system is 233watts, determine the following:(a) The initial discharge in L/s if C=0.63.(b) The thickness of each liquid in m.(c) The coefficient of contraction.
Water at 15°C is to be heated to 65°C by passing it over a bank of resistance heating rods 4 m long and 1 cm in diameter which are maintained at 90°C. The water is approached by the heater rod bank at the normal direction at an average speed of 0.8 m/s. The rods are arranged in line with longitudinal and transverse steps of SL = 4 cm and ST = 3 cm.Determine the number of rows of NL tubes in the direction of flow needed to achieve the indicated temperature rise. I need the solution from fundamental concepts of how the heat flow behaves in the system
For the draining liquid fi lm of Fig. , what are theappropriate boundary conditions ( a ) at the bottom y 5 0and ( b ) at the surface y 5 h ?
As3...Air at atmospheric pressure, 27 °C and %30 RH conditions and with a velocity of 3 m/s flowsparallel to a square water pool having the 10 m x 10m dimensions. Water in the pool is at 33•C. Determine the time required for the water height in the pool to decrease 10 mm.
1. Why we use Reynolds number instead of mean velocity as thecriteria to judge the flow state passing through the pipe? 2. Does the ReDL or the ReDU change when the diameter is changed?3. If we replace the pure water with the oil (Newtonian fluids), doesthe lower limit Reynolds number be the same? Why?
Consider an air solar collector that is 1 m wide and 4 m long and has a constant spacing of 3 cm between the glass cover and the collector plate. Air flows at an average temperature of 45°C at a rate of 0.12 m3/s through the 1-m-wide edge of the collector along the 4-m-long passageway. Disregarding the entrance and roughness effects and the 90° bend, determine the pressure drop in the collector.
a rectangular duct made of commercial steel is used to channel air at 1 atm and 35°C at an avergae velocity of 7m/s. The duct is 15 cm by 20 cm and 12m long. Disregarding the entrance effects, determine the fan power needed to overcome the pressure losses in this section of the duct.
The air at 20 oC flows at a speed of 10 m/s through an iron structure with a cross section of 30 cm x 50 cm and a length of 20 m. Required fan account.
8. A coal fired steam boiler uses 3000 kg of coal per hour. Air required for combustion is 15.5 kg ofcoal at barometric pressure of 98.2 KPa. The flue gas has temperature of 285 degree Celsiusand an average molecular weight of 30. Assuming an ash loss of 11% and allowable gas velocityof 7.5 meters per second. Find the diameter of the chimney 9. The gas density is 0.75 kg per cubic meters and air density is of 1.15 kg per cubic meter. If thedriving pressure is 0.25 KPA. Determine the height of the chimney. 10. A powerplant situated at an altitude having an ambient air of 96.53 KPa and 23.88 degreeCelsius. Flue gases at a rate of 5.0 kg per second enter the stack at 200 degree Celsius andleaves at 160 degree Celsius. The flue gases gravimetric analysis are 18% CO2, 7% O2 and 75%N2. Calculate the height of the stack necessary for a driving pressure of 0.20 KPaKindly answer all please. Thank you
The velocity profile for the fully developed laminar flow of a Newtonian fluid between two large parallel plates is given by as shown in fig.where 2h is the distance between the two plates, u0 is the velocity at the center plane, and y is the vertical coordinate from the center plane. For a plate width of b, obtain a relation for the flow rate through the plates.