) A 75 mm-diameter orifice is on the vertical side of a closed tank. The tank rests on a flat ground and the orifice is 0.5 m above the ground. Filled with four fluids with air on the topmost portion that is under a pressure of 15 KPa, and the rest of specific gravities of 0.80, 1.0, and 1.50, respectively, the jet hits the ground at a horizontal distance of 3.75 m. If the liquids have the same thickness, and the power lost in the system is 233 watts, determine the following: (a) The initial discharge in L/s if C=0.63. (b) The thickness of each liquid in m. (c) The coefficient of contraction.

) A 75 mm-diameter orifice is on the vertical side of a closed tank. The tank rests on a flat ground and the orifice is 0.5 m above the ground. Filled with four fluids with air on the topmost portion that is under a pressure of 15 KPa, and the rest of specific gravities of 0.80, 1.0, and 1.50, respectively, the jet hits the ground at a horizontal distance of 3.75 m. If the liquids have the same thickness, and the power lost in the system is 233 watts, determine the following: (a) The initial discharge in L/s if C=0.63. (b) The thickness of each liquid in m. (c) The coefficient of contraction.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.32P

See similar textbooks

Similar questions

5.4 Evaluate the Stanton number for flow over a tube from the following data: , , , , .
The air-cushion vehicle in Fig. brings in sea-levelstandard air through a fan and discharges it at high velocitythrough an annular skirt of 3-cm clearance. If the vehicleweighs 50 kN, estimate ( a ) the required airflow rate and( b ) the fan power in kW.
An air compressor increases the pressure (Pout > Pin) and the density (?out > ?in) of the air passing through it. For the case in which the outlet and inlet diameters are equal (Dout = Din), how does average air speed change across the compressor? In particular, is Vout less than, equal to, or greater than Vin? Explain.
Oil (SG = 0.89) enters at section 1 in Fig. P3.20 at a weightfl ow of 250 N/h to lubricate a thrust bearing. The steady oilfl ow exits radially through the narrow clearance betweenthrust plates. Compute ( a ) the outlet volume fl ow in mL/sand ( b ) the average outlet velocity in cm/s.
Find the draft loss in rectangular breeching 2.59m x 3.67m x 30.48m long when 196 m3/sec flue gas of 0.769 kg/m3 density are flowing.
A 4.5 m diameter diesel tank has an outlet nozzle of 75 mm in diameter. What is the mass flow rate in kg/s of through the nozzle if specific gravity of diesel is 0.85? Volume of the tank when full is 150000 L.
If the actual draft required for a furnace is 6.239 cm of water and the frictional losses in the stack are 15% of the theoretical draft, calculate the required stack height in meters, the velocity of flue gas, and the diameter of the stack for 43.9 kg/s of flue gas produced. Assume that the flue gas has an average temperature of 149 ℃ and MW of 30. Assume an air temperature of 21 ℃.
Water at 20 ° C, in the pressurized tank of Fig. P3.117, fl owsout and creates a vertical jet as shown. Assuming steadyfrictionless fl ow, determine the height H to which thejet rises.
Consider air flowing past a hemisphere resting on a flatsurface. If the internal pressure is pi, findan expression for the pressure force on the hemisphere. At what point A on the hemisphereshould a hole be cut so that the pressure force willbe zero according to inviscid theory?
Make an analysis of the shape h ( x ) of the water–air interfacenear a plane wall, as in Fig. , assuming that theslope is small, R - 1 ≈ d 2 η / dx 2 . Also assume that the pressuredifference across the interface is balanced by thespecifi c weight and the interface height, ∆p ≈ ρ g η . Theboundary conditions are a wetting contact angle θ at x = 0and a horizontal surface η = 0 as x--->∞. What is themaximum height h at the wall?
pls replyyy Air is flowing through a square conduit whose section changes from 100 mm (section 1) to 200 (section 2). At section 1, v1=6 m/s and the density at section 1 is 1 kg/m3. If the velocity of flow is 1.8 m/s at section 2, find the density of gas at section 2
A 1.0 m radius cylindrical industrial tank filled with viscous oil to a level at a height h from its base, must be drained through a tube with a radius of 0.2 m and length L, connected to its base. The speed profile of oil in the drain tube can be described by the equation below. Where v is the oil speed, vmax is a = maximum oil speed, r is the radius, and R is the tube radius. Considering this problem situation, do what is asked in the following items, justifying your answers. a) What is the volume, in liters, of oil removed from the tank after 10 seconds, if the maximum discharge speed does the oil reach 0.35 m/s? Data: π ≈ 22/7; 1 m3 = 1000 L. b) What flow regime does the system operate? Demonstrate. Data: specific mass of oil = 800 kg/m3, specific mass of water = 1000 kg/m3, oil viscosity = 0.056 Pa.s e viscosity of water = 0.001 Pa.s.