Q6/ Determine the pressure difference between pipes A and B for the differential manometer shown in Fig. Q7/ A shaft of diameter 120 mm is rotating inside a journal bearing of diameter 122 mm at a speed of 360 rpm. The space between the shaft and bearing is filled with lubricating oil of viscosity 6 poise. Find the power absorbed in the oil if the length of bearing is 100 mm. Im Water Water 1.2 m 1.5m H 0.5m 1 Mercury (sp gr 13.6) Water 1.3 m

Q6/ Determine the pressure difference between pipes A and B for the differential manometer shown in Fig. Q7/ A shaft of diameter 120 mm is rotating inside a journal bearing of diameter 122 mm at a speed of 360 rpm. The space between the shaft and bearing is filled with lubricating oil of viscosity 6 poise. Find the power absorbed in the oil if the length of bearing is 100 mm. Im Water Water 1.2 m 1.5m H 0.5m 1 Mercury (sp gr 13.6) Water 1.3 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure shows a siphon that is used to draw waterfrom a large open tank. If the absolute vapor-pressureof the water is pv = 1.23 kPa. (a) determine the shortest drop length L of the50-mm-diameter tube that will cause cavitation in thetube. Show all your calculations. (b) Also draw the energy and hydraulic grade lines forthe length of the tube. Be sure to indicate the pressureheads, elevation heads, and dynamic heads. And toshow all your calculations.
Q6) The space between two parallel plates is filled with oil. Each side of the plate is 60 cm. the thickness of oil film is 12.5 mm. The upper plate, which moves at 2.5 metre per sec requires a force of 98.1 N to maintain the Speed. Determine
A gas tanker carries fuel oil having density of 900kg/m3 and viscosity of 0.05kg/ms as shown in the figure. Thecapacity of the tanker is 20m3 and filling time is 40 minute. Please calculate the required input power of the pump tofill the empty tanker at the beginning of filling process. Note that total irriversible head loss is 2m and the efficiencyof the over-all pump is 82%. Please discuss the amount of required power during the filling process
Two very large open tanks A and F (Fig. ) containthe same liquid. A horizontal pipe BCD, having a constriction at C andopen to the air at D, leads out of the bottom of tank A, and a verticalpipe E opens into the constriction at C and dips into the liquid in tank F.Assume streamline flow and no viscosity. If the cross-sectional area atC is one-half the area at D and if D is a distance h1 below the level ofthe liquid in A, to what height h2 will liquid rise in pipe E? Express youranswer in terms of h1.
A skater weighing 500 N skates at 10 m/s and is supported by an average skating area of 10 cm2. If the viscosity of water is 1 centipoise and the coefficient of friction between skates and ice is 0.02, then find the thickness of thin film of water existing between the skates and the ice. Follow the methodologies in solving the problem; Given : Required: Schematic Diagram: Solution:
In order to measure the speed of the ambient air at atmospheric pressure, a Pitot tube is used, in which water is the gage fluid.. It is known that the ambient air speed is 25 meters per second, when the air temperature is 40 degrees. Celius. Calculate what the differential manometer reading in the pitot tube would be?
A pipe, 12 inch in diameter at A, discharges 4.0 cfs of heavy fuel oil (sp gr = 0.899) into the air at B, where the diameter is 6 inch. If B is 12 ft above A and the frictional loss between the two points is equivalent to 3.0 lb per sq in, determine the pressure at A in pounds per square inch.
plzz help meeeeeeeeee The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
A hemispherical tank of 4 m radius is full of water/ It is fitted with a 60 mm diameter sharp-edged orifice at the bottom. Calculate the time required to lower the level in the cistern by 2 m. Take Cd= 0.6
U - tube is used to pressure the difference in water channel. p1= 1000 kg/m3. The orange fluid in the U - tube has a density: p2= 2000 kg/m3. The height a = 10 cm and h = 15 cm. If the pressure at point ① is 111 kPa, what is the pressure at point ② ?
Determine the surface tension in a tube with 0.3m radius and wetting angle 80 and capillary rise of 4.5mm in N/m and in lb/ft.
A venturi meter measures the flow of water in a 75mm diameter pipe. The difference between the throat and the entrance of the meter is measured by the U-tube contains mercury which is being in contact with the water. Calculate the diameter of the throat if the difference in level of mercury is 250mm when the quantity of water flowing in the pipe is 1.55m3/min. Assume coefficient of discharge is 0.97.