Q6. A hydro-cylinder with an inner diameter of D=200 mm has the oil pressure is p= 1 N/mm?.The cylindrical barrel and the flange are connected by eight uniformly distributed bolts. Therelative stiffness of the bolted connection is ka/(ks +kim) = 0.4. The applied preload is Qp =3F (Fis the operating force) and the allowable stress of bolt material is [0] = 150 N/mm?.(1) The total tensile load carried by each bolt;(2) The resultant load on the clamped members;(3) The minor diameter required for the bolts.

Answered: Image /qna-images/answer/973e60c6-57d4-4b9f-a6a4-c94980be7c88.jpg

Q6. A hydro-cylinder with an inner diameter of D=200 mm has the oil pressure is p= 1 N/mm?. The cylindrical barrel and the flange are connected by eight uniformly distributed bolts. The relative stiffness of the bolted connection is k/(ks +km) = 0.4. The applied preload is Q, =3F (F is the operating force) and the allowable stress of bolt material is [0] = 150 N/mm. (1) The total tensile load carried by each bolt; (2) The resultant load on the clamped members; (3) The minor diameter required for the bolts.

Q6. A hydro-cylinder with an inner diameter of D=200 mm has the oil pressure is p= 1 N/mm?. The cylindrical barrel and the flange are connected by eight uniformly distributed bolts. The relative stiffness of the bolted connection is k/(ks +km) = 0.4. The applied preload is Q, =3F (F is the operating force) and the allowable stress of bolt material is [0] = 150 N/mm. (1) The total tensile load carried by each bolt; (2) The resultant load on the clamped members; (3) The minor diameter required for the bolts.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A radial plain bearing has a diameter of 60 mm and a width of 60 mm. Journal rotation speed 600rpm; radial load acting on the bearing is 3.5 kN, the inlet temperature of the SAE 20 oil used is 30 C andSince r / c = 1000;a-) The increase in the temperature of the oil and its average temperature,b-) Minimum oil film thickness, angular position and eccentricity ratio,c-) Loss of power in the bed,d-) Side leaks and total oil flow,e-) Max. oil film pressure.
A hydrodynamic journal bearing is subject to 2000 N load at a rotational speed of 2000 rpm Both bearing bore diameter and length are 40 mm. If radial clearance is 20 um and bearing is lubricated with an oil having viscosity 0.03 Pa-s, find the Sommerfield number of the bearing.
With free body diagram please thank you. Clear and complete solution please. 3. A shaft 70 mm in diameter is being pushed at a speed of 400 mm/s through a bearing sleeve 70.2 mm in diameter and 250 mm long. The clearance, assumed uniform, is filled with oil at 20°C with v = 0.005m²/ s and sp. gr .=0.9 Find the force exerted by the oil in the shaft.
15- What will be the diameter (in mm) of a water droplet, the pressure inside which is 0.00221 N/cm2 greater than the outside pressure? (Take surface tension as 0.075 N/m)
Constant density and non-viscuous fuid. turbulent static ideal isothermal
The tank in the form of a right-circular cone of radius 5 ft and height 23 ft standing on its end, vertex down, is leaking through a circular hole of radius 3 inches. Assume the friction coefficient to be c=0.6 and g=32ft/s2. Then, the correct equation governing the height h of the leaking water is dh/dt= _______________ If the tank is initially full , it will take it ___________ secs to empty correctly.
An oil well has the following specifications; • Tubing diameter = 2.875” • Tubing roughness = 0.0254 mm • Flow rate = 600 bbl/d • Average reservoir pressure is 4230 psig and Pb is 46335 • Well Depth = 133000 ft 1- Calculate Pwf at 1000, 3000 and 4500 psi. 2- Calculate Pwf at tubing ID 3”, 4” and 5”. Plot Pwf vs Q and determine optimum production rate for both cases Fluid properties GOR 1930 scf/stb Gas Sg is 0.74 Oil API 42 WOR is 0.1 Reservoir temperature 175 F
A fluid having a density of 1400 kg/m³ stands in a tube of 6 mmθ at a height of 27 mm. what is the true static height? use surface tension equals to 0.1052N/m and contact angle is 15degrees.
Working for an engineering consultancy firm, your knowledge of fluid dynamics is required to design a new safety feature for a high-pressure air line in a factory. The air line takes the form of a cylindrical pipe of diameter 150 mm, which is designed to operate between 0.45 MPa and 0.76 MPa. At the end of the pipe a burs9ng disk is placed so that, if the pressure exceeds the maximum opera9ng pressure, the air is vented to atmosphere rather than over-pressuring the chemical reac9on vessel (Figures 4a and 4b). In this ques9on, you should treat the flow as quasione-dimensional and inviscid. The air in the surrounding atmosphere is at 101 kPa and 298 K. a) You have a choice of five disks which can withstand the following forces across them before burs9ng: 10.5 kN, 11.0 kN, 11.5 kN, 12.0 kN, 12.5 kN. Which of these burs9ng disks would you recommend, and why? b) Due to an over-pressurisa9on of the air line, the disk bursts at 9me t = 0. At what pressure in the air line will this occur? c)…
A solid cone of angle 2θ, mass (m), base radius (r0), and density (ρc), is rotating with angular velocity (w0) on its conical seat. The clearance (h) is filled with oil of viscosity (μ). Neglecting air resistance, determine: a) an expression for the moment (M) as a function of r0, w0,μ,θ, and h. b) an expression for the angular velocity (w) for t≥0 as a function of w0,μ,θ,h, r0,m and t if an external torque is not applied. If the radius of gyration of the cone is 16 cm, determine: c ) the value of the angular momentum and velocity if w0=60RPM,h=0.05mm,θ=30°,μ=0.98cPoise , m=20kg, t=2.0s
Please provide solutions. 1. A pipe 2.50 cm in diameter is 1.0 m long and filled with 0.60 m of water. If the pipe is capped at both ends and rotated in a horizontal plane about a vertical axis through one end of the pipe, what is the pressure at the other end of the pipe when it is rotating at 200 RPM? Problem A: An open vertical cylindrical tank 0.60 m in diameter and 1.20 m high is half full of water. If it is rotated about its vertical axis so that the water just reach the top, find the speed of rotation. What will then be the maximum pressure in the tank? If the water were 1.0 m deep, what speed will cause the water to just reach the top? What is the depth of the water at the center? 2. If the tank of Prob. A is half full of oil (sp. gr. 0.75) what speed of rotation is necessary to expose one-half of the bottom diameter? How much oil is lost in attaining this speed? Answer: 18.70 rad/s ; 42.5 litres
A compressed air tank is designed to contain 50 standard cubic feet of air when filled to a gaugepressure of 200 atm at an ambient temperature of 70 F. Assume this is an air tank for scubadiving, and that the approximate shape of the tank is a cylinder with circular cross section. The interior volume of the tank is v=0.253 ft^3(a) If the interior length of the cylinder is 1 ft, what would be the inner diameter?(b) It is desired that the air tank be neutrally buoyant when empty. The density of aluminum is2700 kg/m3. If the tank is made of aluminum, what should be the wall thickness in order forit to be neutrally buoyant?