QB5 BEAM BENDING A cantilever beam of length 8 m is loaded with three point loads as shown in Figure QB5. a) Calculate the vertical reactions and bending moment at support, A. b) Derive the equation for determining the Shear Force and Bending moments along the entire length, hence determine the values of the Shear Forces and Bending moments at points A,B,C and D c)Sketch the Shear Force diagram and the Bending Moment diagrams by inspection. Compare with your results for Bending moments and Shear Force in part (b) 1 50 kN 20 kN 2m 40 kN B D Fig QB5 1m 1m

QB5 BEAM BENDING A cantilever beam of length 8 m is loaded with three point loads as shown in Figure QB5. a) Calculate the vertical reactions and bending moment at support, A. b) Derive the equation for determining the Shear Force and Bending moments along the entire length, hence determine the values of the Shear Forces and Bending moments at points A,B,C and D c)Sketch the Shear Force diagram and the Bending Moment diagrams by inspection. Compare with your results for Bending moments and Shear Force in part (b) 1 50 kN 20 kN 2m 40 kN B D Fig QB5 1m 1m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 9 m simply supported beam carries a linearly varying load from 0 at the left support to 45 kN/m at the right support. Applying shear and moment equations, where x is any distance in the beam from the left support. What is the numerical coefficient of the second to the highest degree in the moment equation? (indicate sign, no sign means positive)a) 2b) 3 c) 0d) 1e) 4
A circular beam carries a concentrated and a distributed load as shown in the figure. Determine the following unknowns if the modulus of elasticity is 90GPa and the maximum shear is 444.9kN. Let, P=170kN, a=2.5m, b=1m and c=3m ; If the deflection at the free end (leftmost part of the beam) is equal to -14.183444485219mm, Determine the radius of the cross-section of the circular beam. Determine the slope at the free end of the beam
A tied column 300 x 350 mm as shown in the figure is reinforced with 6 pieces steel barshaving fy = 414 MPa and fc’ = 21 MPa as shown in the figure. The column is to resist a factoredload of 1200 kN and factored moment of 280 kNm. Using the interactiondiagram, determine the following:a. eccentricity, eb. steel ratioc. diameter of the steel bars
Given the data as shown in the figure, determine the (a) maximum torque Tmax (N·mm) that maybe exerted by the twisting tool and the (b) angle of twist (degree). Use G = 78 GPa and τallowable = 60 MPa
Use THREE MOMENT EQUATION MET determine the member end moments of the beam of the rectangular cross section shown in Figure 11.10a. Assume that support B settles 2 cm. The modulus of elasticity and the moment of inertia of the beam are E = 210,000 N/mm2 and 4.8 × 104 mm,4 respectively. Hint final answer: MAB= 0 MBA= 165.5127 kn.m MBC= -165.5127 kn.m MCB= 52.2604 kn.m
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solutions. a. Vertical Reaction at B in kN.b. Moment Reaction at A in kN-m.c. Deflection at point C in mm.d. Deflection at midspan of AB in mm. Valuea = 3.7b = 26c = 29 Thank you very much!
For the beam loaded as shown in the figure 2, determine the moment reaction at A in kN-m using Conjugate Beam Method. Consider 150 mm x 200 (b x h) mm section and E = 80 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 2.9 m, b = 32.9 kN/m, c = 20 kN.
For the beam loaded as shown in the figure. determine the following unknowns using shear and moment equation or shear and moment diagram. Use a = 5 m, b = 7.6 kN/m, C= 16kN Maximum positive shear in kN. Input positive values only.
For the following simply supported beam: (a) Plot the shear force and bending moment diagrams considering the given loading condition. (b) What are the values of the shear force and bending moment at x = 4.5 m from A? (c) Determine the maximum shear force (Smax) and bending moment (Mmax).
Calculate the plastic moment in KN-m of an A36 steel beam with plastic section modulus of 401,816mm3. Express your answer in 2 decimal places.
Draw the shear-force and bending-momentdiagrams for a cantilever beam AB acted upon bytwo different load cases.(a) A distributed load with linear variation andmaximum intensity q0 (see figure part a).(b) A distributed load with parabolic variation andmaximum intensity q0 (see figure part b).
Consider a uniform beam of 2m long simply supported at both ends, the bending momentis given by the following relation ?′′(?) = ?(?)/?, where y(x) is the deflection, M is thebending moment and E is the flexeural rigidity. Calculate the bending moment at each gridpoint including the two end points assuming that the deflection distribution is among thefollowingx (in m) 0 0.2 0.4 0.6 0.8 1y(x) (incm)0.0 7.78 10.68 8.37 3.97 0Assume ? = 1.2 × 107??2Estimate the values of bending moment M(0.27)