QI/The top surface of the passenger car of a train moving at a velocity of 70 km/h is 2.8 m wide and 8 m long. The top surface is absorbing solar radiation at a rate of 200 W/m2, and the temperature of the ambient air is 30°C. Assuming the roof of the car to be perfectly insulated and the radiation heat exchange with the surroundings to be small relative to convection, determine the equilibrium temperature of the top surface of the car. Ans =35.1 c

QI/The top surface of the passenger car of a train moving at a velocity of 70 km/h is 2.8 m wide and 8 m long. The top surface is absorbing solar radiation at a rate of 200 W/m2, and the temperature of the ambient air is 30°C. Assuming the roof of the car to be perfectly insulated and the radiation heat exchange with the surroundings to be small relative to convection, determine the equilibrium temperature of the top surface of the car. Ans =35.1 c

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.40P

See similar textbooks

Similar questions

An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
The top surface of the passenger car of a train moving at a velocity of 70 km/h is 2.8 m wide and 8 m long. The top surface is absorbing solar radiation at a rate of 200 W/m2, and the temperature of the ambient air is 30°C. Assuming the roof of the car to be perfectly insulated and the radiation heat exchange with the surroundings to be small relative to convection, determine the equilibrium temperature of the top surface of the car.
The top surface of the passenger car of a train moving at a velocity of 115 km/h is 2.8 m wide and 8 m long. The top surface is absorbing solar radiation at a rate of 380 W/m2 and the temperature of the ambient air is 30°C. Assuming the roof of the car to be perfectly insulated and the radiation heat exchange with the surroundings to be small relative to convection, determine the equilibrium temperature of the top surface of the car. The properties of air at 30°C are (Table A-15) k = 0.02588 W/m⋅°C, v = 1.608 × 10−5 m2/s, and Pr = 0.7282.The equilibrium temperature of the top surface of the car is:
An average man has abody surface area of 1.8m2 and a skin temperature of 33degrees celcius .The convection heat transfer coefficient for a clothed person walking in still air is expressed as {h,8.6V^0.53}FOR 0.5<v<2m/s,where V is the walking velocityin m/s.Assuming the average surface temperature of the clothed person to be 30degrees celcius, determine the rate of heat loss from an average man walking in still air at 10degrees celcius by convectionat a walking velocity of (a)0.5m/s (b)1.0m/s (c)1.5m/s (d)2.0m/s
The boiling temperature of nitrogen at atmosphericpressure at sea level (1 atm) is -196°C. Therefore, nitrogenis commonly used in low-temperature scientific studies sincethe temperature of liquid nitrogen in a tank open to the atmosphereremains constant at -196°C until the liquid nitrogen inthe tank is depleted. Any heat transfer to the tank results inthe evaporation of some liquid nitrogen, which has a heatof vaporization of 198 kJ/kg and a density of 810 kg/m3 at1 atm.Consider a 4-m-diameter spherical tank initially filledwith liquid nitrogen at 1 atm and -196°C. The tank isexposed to 20°C ambient air with a heat transfer coefficientof 25 W/m2·K. The temperature of the thin-shelled sphericaltank is observed to be almost the same as the temperatureof the nitrogen inside. Disregarding any radiation heatexchange, determine the rate of evaporation of the liquidnitrogen in the tank as a result of the heat transfer from theambient air.
Q6: A large vertical plate 6.1 m high and 1.22 m wide is maintained at s constant temperature of 57:C and exposed to atmospheric air at 4-C. Caleulate the heat lost by the plate. Answers: Q
a 6cm diameter shaft rotates at 3000rpm in a 20cm - long bearing with a uniform clearance of 0.2mm. At steady operating conditions, both the bearing and the shaft in the vicinity of the oil gap are at 50°c, and the viscosity and thermal conductivity of lubricating oil are 0.05N.s/m^2 and 0.17W/m. k. By simplifying and solving the continuity, momentum, and energy equations, determine: a) the maximum temperature of oil. b) the rate of heat transfer to the bearing and the shaft, and the mechanical power wassted by the viscous dissipation in the oil?
Hi, can you help me to answer this question using the first law of thermodynamics formula to explain this event? On a hot summer day, a student turns his fan on when he leaves his room in themorning. When he returns in the evening will the room be warmer or cooler than theneighborouing rooms ? Explain your answer using the first law of thermodynamics.Assume ALL doors and windows are kept closed.
A long 10-cm-diameter steam pipe whose external surface temperature is 110°C passes through some open area that is not protected against the winds . Determine the rate of heat loss from the pipe per unit of its length when the air is at 1 atm pressure and 10°C and the wind is blowing across the pipe at a velocity of 8 m/s.
air at a dry ball temperature of 80 degrees C and 4% RH is passed over the cooling coil so that the temperature of the air dry ball becomes 35 degrees Celsius. how much heat is released from the air in the process? (answer in kj / kg)
what are the different modes of heat transfer? Explain transfer of heat by convection process?
air is flowing inside of a pipe with radius=0.4 meters at a mass velocity of 29.4 kg/s*m2 at 322 K, with the walls of the pipe at 300 K. At the conditions of the experiment, the viscosity of air is 1.984 x 10-5 Pa*s, the density of air is 1.22 kg/m3, the heat capacity is 1 kJ/kg*K, and the thermal conductivity is 0.025 W/m*K. Determine the rate of heat loss by air per meter of duct.