b) Estimate the yield stress of copper containing an array of equally spaced second phase precipitates, if the atomic radius for copper is 0.128 nm, the shear modulus G = 45 GPa, and the distance between the precipitates, through which the dislocations must pass is L = 0.1um %3D %3D tbl Dislocation Precipitate tbL T

b) Estimate the yield stress of copper containing an array of equally spaced second phase precipitates, if the atomic radius for copper is 0.128 nm, the shear modulus G = 45 GPa, and the distance between the precipitates, through which the dislocations must pass is L = 0.1um %3D %3D tbl Dislocation Precipitate tbL T

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

room temperature plastic deformation of pure lead (pb), with recrystallization temperature of -4, will enhance its: a. tensile strength b. modulus of elasticity c.ductility d. none of the above please explain
Which of the following dislocation reactions are feasible? Show.
10.5 Estimate the amount of solute (atomic percent) necessary to put onesolute atom at each site along all the dislocations in iron. Assume that 1 mm3of iron contains about 106 mm of dislocation lines.
4.26(a) Iron (r = 0.124 nm, G = 70 GPa) is being deformed to a shear strain of0.3. Assuming a constant dislocation density equal to 1010 cm−2, what isthe average distance each dislocation has to move?(b) Assuming that the strain rate is 10−2 s−1, what is the average dislocationvelocity?
Calculate the critical radius of precipitates for which an Al--Mg alloycontaining 10% Mg will be strengthened by Orowan looping instead of particle shear. Use the following data:γAl2Mg = 1.4 J/m2,G Al = 26.1GPa,rAl = 0.143 nm.
Note: Answer Should be not so long. Need straight forward Answer. For minimizing (1) dislocation creep and (ii) diffusion creep, state in each case whether a metal with a small grain size or a large grain size would be the most suitable, giving reasons for your answers.
What are dislocation densities, compare for deformed sample and heat treated of sample?
Calculate the approximate total dislocation line length(or range of lengths) expected in a cubic cm of a very highlycold-worked metal.
A sample of cold-worked metal has a dislocation density of 5x1014 [m/m3]. What is the total length of the dislocation line present in the sample of 1 cm3? If the sample is made of Cu, calculate the total stored elastic energy in [J/m] within the sample for [110] slip direction.
If a series of dislocations produced by a single FrankRead source encounter an impassible barrier, a back stress is created. What is the reason for this back stress, and why is it very effective for dislocations produced by a single F-R source?
Explain the following, using dislocation theory: metal strengthening by: (a) grain size (b) solid solution strengthening (c) strain hardening (d) quenching in cold water following heating close to melting pt ( hint: Nv = Nexp(-Qv/kT)
1. Write down all the possible Burgers vectors of perfect dislocations in an FCC metal. 2. For an a/2[1 dislocation line moving on a (11-1) plane in an FCC crystal, what are the line directions (in Miller indices) if the dislocation is of (i) pure screw and (ii) pure edge character? For an a/2[1 dislocation line moving on a (11-1) plane in an FCC crystal, what are the line directions (in Miller indices) if the dislocation is of (i) pure screw and (ii) pure edge character?