Ques 2 An RLC series circuit has R = 502, C = 50μF and a variable inductance. The applied voltage is 220 V at 100 rad/sec. The inductance is varied till the voltage across resistance is maximum. Under this condition, find the (i). Value of inductance (ii) Q - Factor

Ques 2 An RLC series circuit has R = 502, C = 50μF and a variable inductance. The applied voltage is 220 V at 100 rad/sec. The inductance is varied till the voltage across resistance is maximum. Under this condition, find the (i). Value of inductance (ii) Q - Factor

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 2PP: Assume that the voltage drop across the resistor, ER, is 78 V, that the voltage drop across the...

See similar textbooks

Related questions

Q: Read A 70-Vac source has the following waveform. Determine: a. Vpk b. Vpk-pk c. Vrms d. Period e.…

A: Since you have posted a question with multiple subparts, we will solve the first six parts for you.…

Q: Following are the results of a test carried out on a 230/600 V single phase, 7.5 kVA transformer.…

A: Solution: Given data; single phase transformer, KVA = 7.5 , V1=230 V , V2=600 V In short circuit…

Q: Problem 2.4b: Sketch double sided and single sided amplitude and phase spectra of the following.…

Q: y₂ (1)=2[u(t)-u(t-1)] + [1+cos (πt-n)]-[u(t-1)-u(1-2)]

A: Given: y2t=2ut-ut-1+1+cosπt-π.ut-1-ut-2

Q: 그 Clock D C e D e C B

A: P

Q: 10. The following is part of a larger circuit. The 4 branches extending outward are not open…

A: Given circuit:

Q: A copper-constantan thermocouple is connected to a copper-constantan extension wires and the…

Q: 12] 23 analog signals (each is bandlimited to 11kHz) are transmitted simultaneously channel via the…

A: Given, Number of signals, N=23 The bandlimited frequency of each signal is fm=11 kHz To find: 1)…

Q: Q5/Chose the correct answer for the output F and G of the following circuit (Assume that A=…

Q: A 3-ph, 50 Hz, 150 km line has resistance, inductive reactance and capacitive admittance of 0.1, 0.5…

Q: 6- A system with a unity positive feedback gain has error ratio ----------- where R(s) is the system…

A: Note: We are authorized to answer one question at a time, since you have not mentioned which…

Q: Find V₁ V₂ V₂ > 30V + v. Apply KCL 1.5+ V₂ System J 3.A and KUL I, I2, I3 J + 162 Omh's law J and of…

A: A circuit diagram is shown ab below. Find V1, V2, V3, and I1, I2, I3.

Q: A class B push-pull amplifier with transformer coupled load uses two transistors rated 10 W each.…

A: We have a class-B push pull amplifier with transformer coupled load uses two transistors . We need…

Q: 1- For a system with the transfer function Y(s) 2s³ - 12 U(s) 4s5 S3 + 4s 10 The state matix is…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: SKILL BUILDING ACTIVITY # 3 A standard AM broadcast station is allowed to transmit modulating…

Q: Find current l₁ in the figure. R₁ 100 Ω www +0 100 mA k A. 60 B. 68 MA C. 50 mA D. 32 mA 12 R₂ 47 92

A: The given circuit is,

Q: Find the main dimensions of a 2000 kVA, 187.5 rpm, 50 Hz, 3 phase salient pole synchronous…

Q: he minimum multiplexers using to design 128-to-1 multiplexer are 32( 4-to-1 mux) without enable…

Q: How can you convert a galvanometer into an ammeter and a voltmeter? A PMMC galvanometer of 60…

A: Given- Resistance of galvanometer- Ri=6 Ω,IFSD=60 mA, To Find- (i) Value of resistance when…

Q: 2. Calculate Vout. A = 2 x 10^5 OV 3ΚΩ GAL 5ΚΩ 1ΚΩ 10V VI 12 + Wheatstone Bridge Differential…

Q: Determine whether the following signals are energy, power, or neither energy nor power.

Q: 3. Given a system with input x(t) = u(t) and impulse response h(t) shown below. Determine: a) The…

A: Use convolution integral to find convolution of the x(t) and h(t).

Q: (Q2] 23 analog signals (each is bandlimited to 11kHz) are transmitted simultaneously over a channel…

A: Given that Number of signals, N=23 The bandwidth of each signal, fm= 11 kHz. Find Sampling…

Q: 1.1 Find the current flowing through an element if the charge flowing through the element is given…

A: In all the cases for t < 0 , current will be zero. The current can be given by: i=dqdt a)…

Q: 12 A discrete relay type output module can be used to switch either AC or DC load devices. Why? OIt…

A: Relay:- An electrically controlled switch is a relay. It is made up of a set of working contact…

Q: A star-connected, 3-phase, 15 MVA, 3.3 kV alternator is protected by Merz Price circulating-current…

A: Given,For a 3-ϕ star connected alternator,S=15 MVAVL=3.3 kVR=8 ΩImin = 0.5 ACT ratio=10005

Q: 26. In a 3-phase, 4-wire unbalanced system, the current in the neutral wire is 12A. The zero…

A: Given: In a 3-phase, 4-wire unbalanced system with, Neutral current, IN=12 A

Q: The maximum values of voltage and current in a circuit are 400 V and 20 A respectively. Both the…

Q: Q8 a) b) Find and sketch o(t) = f(t)* f(t) for the pairs of functions shown as follow: B : (1) 1₁…

Q: Identify and realise the H(s) compensator with Operational amplifier. S+ 0.1\/S + 1 H(S) = (Sto…

A: Given data, Hs=s+0.1s+0.01s+1s+10

Q: 1. Find io 22 ΦΩ 6V 다 12 W 42 3A 12V

Q: 6. If the rms current through a 4.7 k resistor is 4 mA, the peak voltage drop across the resistor is…

A: Given data, RMS current flowing through resistor, irms=4 mA Value of resistance, R=4.7 kΩ

Q: design using JK-flip flops a logic circuit that detects the nonoverlapped sequence [10011]

Q: Given the AM voltage equation. Determine the carrier voltage and frequency, the modulating voltage…

A: Given: VAM=310 cos (6,540,000 t)+650 sin (6,600,000 t) - 310 cos (6,660,000 t) Volts To do:…

Q: the figure below, where f 60kHz, 45kHz, 25kHz if ide

A: Given:

Q: ГО - A system with a state matrix A = [₁1] is in. a- critical damped b- over damped c- under damped…

A: NOTE- “Since you have asked multiple questions, we will solve the first question for you. If you…

Q: QUESTION 7 With reference to PLC discrete output modules: What types of fi eld output devices are…

Q: A 500 KVA, 1100 V, star connected alternator has an effective armature resistance of 0.2 Ω per…

Q: A DC motor has an internal resistance of 70. This motor has a no load speed of 3912rpm at 20V. This…

Q: 2 A single phase transmission line having a resistance of 25 Q is connected to fixed sender voltage…

Q: A DC generator with 8 pole, duplex lap winding excited with a flux of 3mWb/ pole. The number of…

A: Given: A DC generator with number of pole, P=8. Multiplexity of lap winding, m = 2 (duplex winding).…

Q: 1.5-5 Determine the currents i, i, in the circuit of Fig. P1.5-5. Answers: ix = 10 A, i, = -7 A. 3 A…

A: The question is about KCL. Kirchhoff’s Current Law (KCL) : Definition: the total current entering in…

Q: The Commonly Used Types of Power Supply Use and Applications of power supply

A: A power supply can be described as an electrical device used to provide energy to consumers. These…

Q: a) Design minimal circuit. With 4-bit variable using K-map that gives an output 1 when have three 1…

A: Let the 4 inputs for our k-map design be A, B, C, and D. Let the output be F. It had been given that…

Q: Determine vx in the circuit of Fig. 3.10a. 60 VI 5Α Μ 8 Ω www Μ 4Ω 10 Ω (α) Μ 2 Ω + I ix

Q: A ramp input applied to an unity feedback system results in 5% steady state error. The type number…

A: Given- Steady state error=5%, To Find- The type number and velocity error constant of the system.

Q: A. Determine whether or not the following signals are periodic. In case a signal is periodic,…

A: In the given questions we need to calculate the fundamental frequency of the given signal.

Q: Using J-K. fp, design asynchronous counter to count binary sequence from 0100 to 1100, Corresponding…

Q: If IR1 = 0.065 mA and IR2 = 0.098 mA in a two branch parallel circuit, IT = 0.163 mA. True False

A: Given, In two parallel branch circuit the currents in each branch is, IR1=0.065 mA,IR2=0.098 mA. And…

Q: Find Vx, VBF, and VÅB in the network in Figure shown below. 4 V D

Concept explainers

Capacitor

The capacitor is an element used to store electrical energy in the electrical field. A capacitor is a form of passive energy.

Question

Ques 2 An RLC series circuit has R = 502, C = 50µF and a variable inductance. The applied
voltage is 220 V at 100 rad/sec. The inductance is varied till the voltage across resistance is
maximum. Under this condition, find the
(i). Value of inductance
(ii) Q - Factor

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Assume that the voltage drop across the resistor, ER, is 78 V, that the voltage drop across the inductor, EL, is 104 V, and the circuit has a total impedance, Z, of 20 . The frequency of the AC voltage is 60 Hz. ETITZ20VAPFER78VIRRPEL104VILXLVARsLL
Assume that the current flow through the resistor, IR, is 15 A; the current flow through the inductor, IL is 36 A; and the circuit has an apparent power of 10,803 VA. The frequency of the AC voltage is 60 Hz. ET ER EL IT IR15A IL36A Z R XL VA10,803 P VARSL PF L
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
A series L–R–C circuit has a supply input of 5 volts. Given that inductance, L = 5 mH, resistance, R = 75ohm and capacitance, C = 0.2µF, determine (c) the frequency at which the p.d. across the capacitance is a maximum and (d) the value of the maximum voltage across the capacitor. answer: c) 4741 hz, d)10.85volts
A pure inductance of L = 120 mH is connected to a V = 102 V, 50 Hz supply. The current taken by the inductor is given by
A 200 Ω resistor, 0.900 H inductor, and 6.00 µF capacitor are connected in series across a voltage source that has voltage amplitude 30.0 V and an angular frequency of 250 rad/s. (a) What are v, vR, vL, and vC at t = 20.0 ms? Compare vR + vL + vC to v at this instant. (b) What are VR, VL, and VC? Compare V to VR + VL + VC. Explain why these two quantities are not equal.
17. Suppose we have a RC circuit with an alternating voltage V(t) = V_{m} * cos(5t) If the initial voltage is 4V and the resistor has a resistance of 8 ohm and the capacitor is of capacitance 2F then the charge for the circuit is?
The current through a 100-mH inductance is given by i( t )=exp( −t ) sin( 10t ) in which the angle is in radians. Determine the voltage across the inductance. Then, use the computer program of your choice to plot both the current and the voltage for 0≤t≤3 s.
Find the impedance theoretically of a wire if it carries the frequency 10 kHz have a voltage is 8v, the current is 2mA, resistance is 12 kΩ , inductance 27 mH and capacitance 0.2 µf
Find the equivalent capacitance (μF) seen at the terminals of the circuit below.
A circuit is designed with an AC source of max voltage 12 and frequency 60 Hz. The circuit has a resistance of 1050 Ohms, an inductance of 0.06 Henrys, and a capacitance of 0.009 coulombs per volt. - omega for source in rad/s? - omegaR for circuit? -XL? -XC? -phi in radians? -Z? -imax?
a series r-c circuit takes a current whose equation is i=0.85sin(754t+pi/4) when connected to a source of emf having the equation e=340sin754t. calculate the capacitance of the capacitor, circuit power factor, and power.