QUESTION # 01 The armature winding of a DC motor has 360 conductors, of which only 80% le directly under the pole, where the flux density B = 1.1 T. The armature diameter is 30 cm and its length is 20 cm. The conductor current is 16 A. Determine: a) The total force created by the conductor. b) The shaft torque developed.

QUESTION # 01 The armature winding of a DC motor has 360 conductors, of which only 80% le directly under the pole, where the flux density B = 1.1 T. The armature diameter is 30 cm and its length is 20 cm. The conductor current is 16 A. Determine: a) The total force created by the conductor. b) The shaft torque developed.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3.3. The current in a conductor on the armature of a DC motor is 300A. The flux under the poles is 850 micro-Weber. The area per pole is 700 mm². The length of the conductor on the armature is 640mm. Calculate the force exerted on the conductor.
A dc motor has an armature containing 192 conductors, 70 percent of which lie directly under the pole faces at any given instant. If the flux density under the poles is 52,000 lines per square inch and the armature diameter and length are 12 in and 4.5 in., respectively, calculate the current in each armature conductor for a torque of 120 lb-ft.
A four-pole shunt motor has an armature with a total of 282 conductors. If each pole face has an area of 25 sq. in. and the flux density is 50,000 lines per square inch, calculate the horsepower that will be developed by the motor for a speed of 1,450 rpm?
4.(dc motor) A 6-pole, simplex wound armature having 720 conductors, rotates in the field of 20.35mwb. if the induced armature voltage is 420v, what is the motor speed?
The current in a conductor on the armature of a dc motor is 300A. The flux under the poles is 850x10-6 Wb. The area per pole is 700 mm2. The length of the conductor on the armature is 640mm. Calculate the force exerted on the conductor.
1.- The production of a force in a conductor carrying current that is inside a magnetic field, is the basis of? 2.- What happens in the flux of a ferromagnetic core of a transformer if the cross section is reduced? : 3.- This force is present internally in the DC motor when the rotor rotates within the magnetic field. 4.- What happens if the field circuit opens in a shunt connected direct current generator?
A 4-pole lap -wound dc generator is designed to have an average airgap flux density of 0 .8 T. The armature winding resistance is 0 .3 Ω, and the brush contact drop is 1 V. There is a slight fault in the magnetic circuit which causes the emfs in two of the paths to be 5 %more than the nominal value, and the emfs in the other two paths 5 %less . a) If the generator supplies a full load of 4 .5 kw at 150 V, find the nominaland actual values of path emfs, coil currents, and armature copper loss. b) Find the nominal and actual values of coil currents and armature copperloss when the generator has no external load.
Calculate the efficiency of a 200-V, 100-kW shunt generator if the resistance of the armature and shunt respectively are 0.005 ohm and 20 ohms. The friction, windage and iron losses together amount to 3,000 W.
The armature of a 6-pole D.C. machine has a diameter of 350mm and is wave wound with 800 conductors occupying slots of effective length 200mm. The fraction of conductor contributing to torque at any instant is 70%. The average magnetic flux density B = 0.1T and flux per pole is 4mWb. The armature of the motor takes 70A at a speed of 600 rad/s. Calculate: b)Estimate the back, e. m. f., induced by the machine, and The supply voltage if the effective armature circuit resistance is 1.6 Ω
A 220 V , 60 Hz , supply is connected to 200 – turn armature winding of reluctance 1.7x105 At / Wb . Find : 1-the magnetizing reactance. 2-the rms values of the ( magneto – motive force , exciting and armature currents , magnetic flux.) 3-the inductance. 4-Draw the phasor diagram of the circuit.
A four-pole shunt motor has an armature with a total of 282 conductors. If each pole face has an area of 25 in² and the flux density is 50,000 lines per sq. inch. Calculate the power developed by the motor in horsepower for an armature current of 85 A and a speed of 1420 rpm. (Assume a wave-connected armature winding).
The armature of a dc motor has 648 conductors, 65 % of which are directly under the pole where the flux density is 48,000 lines per in2. If the core diameter is 7 inches and its length is 4 inches and the current in each conductor is 20 A. What is the torque exerted in the armature in N-m?