Q A four pole self excited DC shunt generator ruining at 104,66 rad's, supplies resistive load 18 Kw 1.1 N constant resistance, the flux per pole is 0.02 Wb.What will be the new generated power if the rotor speed increased to (20%) ?. and the flux per pole increased to (80%), armature resistance is 0.037 2 and shunt ficld resistance is 220 2. Assume that the armature current increased to (10%) when the rotor speed increased.

Q A four pole self excited DC shunt generator ruining at 104,66 rad's, supplies resistive load 18 Kw 1.1 N constant resistance, the flux per pole is 0.02 Wb.What will be the new generated power if the rotor speed increased to (20%) ?. and the flux per pole increased to (80%), armature resistance is 0.037 2 and shunt ficld resistance is 220 2. Assume that the armature current increased to (10%) when the rotor speed increased.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.3P

See similar textbooks

Similar questions

Q23) A shunt generator supplies a 20KW load at 200V through cables of resistance, R = 100mΩ. If the field winding resistance ,Rf=50Ω and the armature resistance, Ra=40mΩ, i) Estimate terminal voltage across the load. ii) Calculate the emf generated in the armature.
Of a shunt excited DC generator, Excitation winding internal resistance Rf = 2.5 Ω Armature winding internal resistance Ra = 0.5 Ω A rheostat has been placed in the excitation circuit to keep the machine's end voltage constant at Va = 30 V. Machine Voltage magnetization induced in the armature while operating at n = 1400 rpm at If = 7 A excitation current It is determined as Ea = 30 V from its characteristic. According to this, a) With peak voltage Va = 30 V, excitation current If = 7 A, power supplied to the load when the speed n = 1400 rpm What is the resistance of the rheostat? b) Spindle revolutions are reduced to n = 1000 rpm. In this case Va = 30 V and Ea = 37 V constant What value should the rheostat be adjusted to keep it? Calculate the power given to the load in this new case.
A 20KW, 440V, short shunt compound dc generator has full load efficiency of 87%. If the resistance of the armature and interpoles is 0.4ohm and that of the series and shunt fields 0.25ohm and 240ohms respectively, calculate the combined bearing friction, windage and core loss of the machine A 10 kW 250 volts self-excited generator, when delivering rated load, has an armature-circuit voltage drop of 5% of the terminal voltage and a shunt field current equal to 5% of the rated load current. The resistance of the armature is 0.02 ohm. Calculate the voltage generated and power output.
A 150-kW 250-volt compound generator is connected long shunt. If the shunt field resistance is 20 ohms, what is the series field-current at full load? (Ans.: 612.5 A) write diagram, given, etc
Determine the e.m.f. generated of a short-shunt compound generator supplies 100 A at 400 V. If the field resistance, Rf =20 Ω, and the armature resistance, Ra =0.06 Ω. If you know that the volt drop in series winding is 2 V
Q/ dc shunt generator 4 pole with 500 condcutor , wave running at speed 1000 r.p.m the resistance of armature and field are 0.02 , 55 ohm and delivering load 43.12kwatt at terminal voltage 220 volt, the iron losses is 750 watt 1-Torque developed by the prime mover .........and The torque developed by the armature ........... when running at 1000 r.p.m * 2-The load current ,,,,,,,,,,,,when the speed drops to 800 r.p.m. if If is unchanged ? * 3-Output of the prime motor…….kwatt * 4-Mechanical , electrical and overall efficiency …….. * 5-Flux per pole is......... wb *
A long shunt compound generator delivers 100 A at 250 V. The armature, shunt field and series field resistances are 0.02 Ohms, 50 Ohms and 0.05 Ohms respectively. If the Break Horse Power (BHP) or the power developed by the shaft torque of the driving engine is 40, determine the stray loss.
A long-shunt compound d.c. generator with armature, series field and shunt field resistance of 0.5, 0.4 and 250 Ω respectively gave the following readings when run at constant speed : Load current (A) : 0 10 20 30 40Terminal p.d. (V) : 480 478 475 471 467 Plot the curve of internal generated e.m.f. against load current. Explain fully the steps by which this curve is obtained and tabulate the values from which it is plotted.
The open-circuit characteristic of a shunt generator when driven at normal speed is as;Field current (A)0.51.01.52.02.53.03.5O.C. volts (V)54107152185210230240The resistance of armature circuit is 0.1 Ω. Due to armature reaction the effective field current is given by the relation Ish (eff.) = Ish − 0.003 Ia. Find the shunt field circuit resistance that will give a terminal voltage of 220 V with normal speed (a) on open circuit (b) at a load current of 100 A. Also find (c) number of series turns for level compounding at 220 V with 100 A armature current; take number of shunts turns per pole as 1200 and (d) No. of series turns for over-compounding giving a terminal voltage of 220 V at no-load and 230 V with 100 A armature current.
The open-circuit characteristic of a shunt generator when driven at normal speed is as;Field current (A)0.51.01.52.02.53.03.5O.C. volts (V)54107152185210230240The resistance of armature circuit is 0.1 Ω. Due to armature reaction the effective field current is given by the relation Ish (eff.) = Ish − 0.003 Ia. Find the shunt field circuit resistance that will give a terminal voltage of 220 V with normal speed (a) on open circuit (b) at a load current of 100 A. Also find (c) number of series turns for level compounding at 220 V with 100 A armature current; take number of shunts turns per pole as 1200 and (d) No. of series turns for over-compounding giving a terminal voltage of 220 V at no-load and 230 V with 100 A armature current.please answer only part C and D
A 220V short-shunt compound generator has armature resistance, series field resistance and shunt field resistances of 0.6, 0.44 and 300 - 16 respectively. If the generator supplies a 10+16 kW load at a rated voltage, find the induced voltage in the armature. Ignore armature reaction. Find the efficiency if the mech and core loss is 500W
A shunt generator supplies a 20kW load at 200V through cables of resistance, R= 100mΩ. If the field winding resistance, Rf =50Ω and the armature resistance, Ra =40mΩ, determine (a) the terminal voltage, and (b) the e.m.f. generated in the armature