Question-03: CLO3 A conical tube of length 2m is fixed vertically with smaller end upward. Velocity of flow at smaller end is 5m/s while at larger end is 2 m/s. The pressure head at the smaller end is 2.5 m of flowing liquid. Loss of head in the 0.35 ( tube is given by-SIe-2, where vị is velocity at smaller end while v2 is velocity at larger end. Solve for the 2g pressure head at the other end if the flow takes place a) downward, b) upward direction (10)

Question-03: CLO3 A conical tube of length 2m is fixed vertically with smaller end upward. Velocity of flow at smaller end is 5m/s while at larger end is 2 m/s. The pressure head at the smaller end is 2.5 m of flowing liquid. Loss of head in the 0.35 ( tube is given by-SIe-2, where vị is velocity at smaller end while v2 is velocity at larger end. Solve for the 2g pressure head at the other end if the flow takes place a) downward, b) upward direction (10)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Obtain the gage pressure at the center A of the pipe shown. Neglect surface tension effects. For Liquid 1 specific gravity= 1.5, for liquid 2 specific gravity= 3.2, h1=15cm, h2= 30cm,h3=75cm
The flowrate of the flow is 0.20 + a/10 m3 /s in a pipe placed on a horizontal plane. The pipe diameters are D1= 0.30 m and D2= 0.20. Please find the force acting to the pipe by the flow. The gauge pressure at (1) is p1 =200 + b*10 kN/m2 . (g=9,81 m/s2, g=10kN/m3 ) a= 4 b=3
Obtain the gage pressure at the center A of the pipe shown. Neglect the surface tension effects. Liquid 1, sg=1.5. Liquid 2, sg=3.2, h1=15cm; h2=30 cm; h3=75 cm.
P-1. The diverging tube shown in the figure discharges oil when h=2 m. The area A is twice the area Ao. Neglecting all friction losses, find thea. Velocity at the throatb. Pressure head at the throat
Water at 20°C flows through a 300-mm-diameter pipe that discharg sphere as shown in Figure 4.61, When a partially open val the top of the pipe, the flow rate in the pipe is 0.2 m*s and the (gauge) pressure just upstream of the valve is 600 kPa. Estimate the force partially open valve, es into the atmo- ve extends 200 mm from exerted by the water on the —Valve 0.2 mYs —» Atmosphere Figure
Water at 60°F is siphoned between two tanks as shown in Figure P8.27. The connecting tube is 2.0 in. diameter smooth plastic hose 20 f t long. Find the volume flow rate and the pressure at point P, which is 8 f t from the entrance to the tube. Ignore minor losses. (To begin, assume a friction factor, then iterate.)
An open circular cylinder with 2m of water is acted upon by an unbalanced upward force of 20 kN. The volume of water inside the cylinder is 6.28 m^3. a. Compute the acceleration of the tank. b. Compute the pressure at the bottom of the tank. Use density of water as 1000kg/m3 and specific weight as 9.81kN/m3
A centrifugal pump which runs at 104.3 rad ·s−1 (16.6 rev/s) is mounted so that its centre is 2.4 m above the water level in the suction sump. It delivers water to a point 19 m above its centre. For a flow rate of Q (m3 ·s−1) the friction loss in the suction pipe is 68Q2 m and that in the delivery pipe is 650Q2 m. The impeller of the pump is 350 mm diameter and the width of the blade passages at outlet is 18 mm. The blades themselves occupy 5% of the circumference and are backward-facing at 35◦ to the tangent. At inlet the flow is radial and the radial component of velocity remains unchanged through the impeller. Assuming that 50% of the velocity head of the water leaving the impeller is converted to pressure head in the volute, and that friction and other losses in the pump, the velocity heads in the suction and delivery pipes, and whirl slip are all negligible, calculate the rate of flow in liter/s and the manometric efficiency of the pump.
Compute the velocity head of the jet if the larger diameter is 10cm and the smaller diameter is 30mm. The pressure head at point 1 is 30m of the flowing water and the head lost Between points 1 and 2 is 5% of the velocity head in the jet.
The container is partially filled with oil, water, and air. Take ??=62.4 ??/??3, ??=58.4 ??/??3, determine the pressure at point A.
1. An orifice in the side of a vertical tank discharges oil (sp. gr. = 0.82) under a head of 4.0 m. and 25 KPa pressure acting on the surface of the oil. If the diameter of the orifice is 5 cm, the coefficient of contraction is 0.62, and the head lost on the orifice is 45 cm, determine the discharge, coefficient of velocity, and the coefficient of discharge.
Water flows from a to e through the pipe system shown in the figure. It is known that the flow in pipe bfgc is 50 liters per sec. (a) Assuming that C1 = 120 for all the pipes, determine the total flow from a to e. (b) Assuming that all the pipes are level and that the pressure head at a is 80 m, determine the pressure head at point d.